Camshaft Replacement
Camshaft Replacement (1.8L LUW and LFH)
Special Tools
* EN-422 - Installer
* EN-6628-A - Locking Tool
For equivalent regional tools, refer to Special Tools Special Tools.
Removal Procedure
1. Remove the camshaft adjuster. Refer to Camshaft Position Actuator Adjuster Replacement Camshaft Position Actuator Adjuster Replacement.
2. Remove the rear timing belt cover. Refer to Timing Belt Rear Cover Replacement (1.6L LDE, LXV, 1.8L 2H0, LUW and LFH) Timing Belt Rear Cover Replacement.
3. Remove intake camshaft position sensor. Refer to Camshaft Position Sensor Replacement (LDE, LXV, LUW, 2H0 and LFH) Service and Repair.
4. Remove exhaust camshaft position sensor. Refer to Camshaft Position Sensor Replacement (LDE, LXV, LUW, 2H0 and LFH) Service and Repair.
5. Remove EN-6628-A - locking tool.
Counterhold at hexagon of camshaft.
Note: Note removal sequence 1-4.
6. Remove the 4 camshaft bearing cap bolts.
Note: Release the bearing support by striking it gently with a plastic hammer.
7. Remove the first camshaft bearing cap (1).
8. Loosen the 8 exhaust camshaft bearing cap bolts working from outside to inside in a spiral in steps of 1/2 up to 1 turn.
9. Remove the 8 exhaust camshaft bearing cap bolts.
Note: Mark camshaft bearing caps before removal.
10. Remove the 4 exhaust camshaft bearing caps Numbers 6-9 from the cylinder head.
11. Remove the exhaust camshaft (1).
12. Loosen the 8 intake camshaft bearing cap bolts working from outside to inside in a spiral in steps of 1/2 up to 1 turn.
13. Remove the 8 intake camshaft bearing cap bolts.
Note: Mark camshaft bearing caps before removal.
14. Remove the 4 intake camshaft bearing caps Numbers 2-5 from the cylinder head.
15. Remove the intake camshaft (1).
16. Detach the seal rings from the camshafts.
Installation Procedure
Note: Lubricate with clean engine oil.
1. Install the intake camshaft (1).
Note: Note the identification marking on the camshaft bearing cover.
2. Install the 4 intake camshaft bearing cover Numbers 2-5.
Caution: Refer to Fastener Caution Fastener Caution.
3. Install the 8 intake camshaft bearing cover bolts and tighten in a spiral from the inside to the outside to 8 Nm (71 lb in).
Note: Lubricate with clean engine oil.
4. Install the exhaust camshaft (1).
Note: Note the identification marking on the camshaft bearing cover.
5. Install the 4 exhaust camshaft bearing cover Numbers 6-9.
6. Install the 8 exhaust camshaft bearing cover bolts and tighten in a spiral from the inside to the outside to 8 Nm (71 lb in).
Note: Sealing surfaces must be free from oil and grease.
7. Clean sealing surfaces of the first camshaft bearing support and the cylinder head with a suitable tool.
Clean oil duct from any sealant residue.
Note:
* Sealing surfaces must be free from oil and grease.
* It is essential to ensure that no sealant is applied outside the marked sealing areas.
* The grooves adjacent to the sealing surfaces must remain free from sealant.
8. Apply surface sealant to sealing surfaces (1) of the first camshaft bearing cap thinly and evenly.
9. Position the first camshaft bearing cap on the cylinder block and tighten the bolts approximately to 2 Nm (18 lb in).
Note: No sealant may reach the camshafts.
10. Install the first camshaft bearing cap (1).
Note: Note installation sequence 1-4.
11. Install the first camshaft bearing cap bolts and tighten to 8 Nm (71 lb in).
12. Install 2 NEW sealing rings to the camshafts.
13. Tighten the seal ring with EN-422 - installer (3) on the camshaft until this is in contact with the cylinder head.
14. To install, use camshaft sprocket bolt (1) in conjunction with shims (2) with a total thickness of approximately 10 mm (0.394 in).
15. Remove the EN-422 - installer (3).
16. Turn the intake camshaft against the direction of engine rotation.
17. Install EN-6628-A - locking tool.
18. Turn the exhaust camshaft in the direction of rotation of the engine.
19. Install EN-6628-A - locking tool.
20. Install exhaust camshaft position sensor. Refer to Camshaft Position Sensor Replacement (LDE, LXV, LUW, 2H0 and LFH) Service and Repair.
21. Install intake camshaft position sensor. Refer to Camshaft Position Sensor Replacement (LDE, LXV, LUW, 2H0 and LFH) Service and Repair.
22. Install the rear timing belt cover. Refer to Timing Belt Rear Cover Replacement (1.6L LDE, LXV, 1.8L 2H0, LUW and LFH) Timing Belt Rear Cover Replacement.
23. Install the camshaft adjuster. Refer to Camshaft Position Actuator Adjuster Replacement Camshaft Position Actuator Adjuster Replacement.