Pinpoint Test AK: Power-Fold Seat Motor (Backrest) and Sensor Functional Test - LH Third Row Power Seat
Seats
Pinpoint Tests
Pinpoint Test AK: Power-Fold Seat Motor (Backrest) and Sensor Functional Test - LH Third Row Power Seat
Refer to Wiring Diagram Set 120, Power Seats for schematic and connector information. Diagrams By Number
Normal Operation
The Power-Fold Seat Module (PFSM) supplies voltage and ground to the power-fold seat motor to move the seat to and from the FOLD and NORMAL positions when selected by the seat control switch. When FOLD is selected the backrest folds forward and releases the spring loaded headrest. If an obstruction is detected in the FOLD/NORMAL axis of movement the seat stops, reverses movement a few inches and then stops again until the obstruction is removed. When the obstruction has been removed the seat control switch must be depressed again to reset the request. The seat goes to the power-fold seat motor home position (seat folded and latched to floor) and then continues with any seat position requested. If the PFSM detects a power-fold seat motor circuit fault (open or short), motor operation is disabled. If a short to ground is present the motor works in only one direction.
A Hall effect sensor is located inside each of the power-fold seat motor assemblies to detect motor movement and seat position to the PFSM. If the sensor does not detect motor movement during a request from the seat control switch, the PFSM disables the power-fold seat motor output.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Power-fold seat motor (backrest) and sensor
- PFSM
PINPOINT TEST AK: POWER-FOLD SEAT MOTOR (BACKREST) AND SENSOR FUNCTIONAL TEST - LH THIRD ROW POWER SEAT
NOTICE: The following pinpoint test uses a test light to simulate normal circuit loads. Use only the test light recommended in the Special Tools table. To avoid connector terminal damage, use the Flex Probe Kit for the test light probe connection to the vehicle. Do not use the test light probe directly on any connector.
NOTE: Verify good battery condition before diagnosing the Power-Fold Seat Module (PFSM) system. Poor battery condition may interfere with PFSM operation. If battery voltage drops below 10 volts, seat movement does not start. If battery voltage drops below 8 volts, a started seat movement stops.
NOTE: The accessory delay system (courtesy lamps) times-out after 10 minutes and disables the third row power seat operation. Meter voltage measurements may be inaccurate when this occurs, which could lead to misdiagnosis. To enable the accessory delay system during diagnosis and testing, close and open any vehicle door.
-------------------------------------------------
AK1 CONFIRM THE FUNCTIONAL TEST HAS BEEN COMPLETED
- Verify the Functional Test - Third Row Power Seat has been completed before testing the power-fold seat motor (backrest) and sensor.
- Has the Functional Test - Third Row Power Seat been completed?
Yes
GO to AK2.
No
CARRY OUT the Functional Test - Third Row Power Seat. GO to Pinpoint Test AF and return to this test only if directed to do so. Pinpoint Test AE: The Power Lumbar is Inoperative - Driver
-------------------------------------------------
AK2 CHECK THE PFSM FOR OUTPUT VOLTAGE TO THE POWER-FOLD SEAT MOTOR
- Access the PFSM. To access the PFSM, refer to the appropriate steps in Power-Fold Seat Module (PFSM) Power-Fold Seat Module (PFSM).
- NOTICE: Before moving the seat, make sure all parts are out from under it or damage can occur.
- Reposition the PFSM and wiring away from the seat so that the seat can be moved during testing without damaging the PFSM or wire harness.
- Detach the PFSM and wire harness completely from the LH load floor flapper panel.
- Lower the PFSM and wire harness to the floor in front of the seat.
- Before the seat is moved, make sure the wiring is clear from the pivot areas of the seat and can not be pinched or torn by seat movement.
- Verify the vehicle is in PARK and the liftgate is open.
- Verify the courtesy lights are on. If needed, close and open any door on the vehicle.
- Connect a test lamp between PFSM C4250C-8, circuit CPS42 (BU/WH) and PFSM C4250C-9, circuit CPS43 (GN/WH), by back-probing the connector.
- Press the NORMAL button then the FOLD button, monitor the test lamp and allow the seat to complete any movement.
- Does the test lamp illuminate (may be momentary) when either button is pressed?
Yes
GO to AK5.
No
GO to AK3.
-------------------------------------------------
AK3 CHECK THE POWER-FOLD SEAT MOTOR AND CIRCUITS FOR A SHORT TO GROUND
- Disconnect: PFSM C4250C.
- Measure the resistance between:
- PFSM C4250C-8, circuit CPS42 (BU/WH), harness side and ground.
- PFSM C4250C-9, circuit CPS43 (GN/WH), harness side and ground.
- Are the resistances greater than 10,000 ohms?
Yes
GO to AK11.
No
GO to AK4.
-------------------------------------------------
AK4 CHECK THE POWER-FOLD SEAT MOTOR AND CIRCUITS FOR A SHORT TO GROUND
- Remove the backrest latch outer cover to gain access to the LH power-fold seat motor electrical connector. Refer to Seat - Exploded View, Third Row Seat - Exploded View, Third Row.
- Disconnect: LH Power-Fold Seat Motor C4245.
- Measure the resistance between:
- PFSM C4250C-8, circuit CPS42 (BU/WH), harness side and ground.
- PFSM C4250C-9, circuit CPS43 (GN/WH), harness side and ground.
- Are the resistances greater than 10,000 ohms?
Yes
INSTALL a new power-fold seat motor. REFER to Power-Fold Seat Motor - Third Row Power-Fold Seat Motor - Third Row. TEST the system for normal operation.
No
REPAIR the affected circuit(s). TEST the system for normal operation.
-------------------------------------------------
AK5 CHECK THE POWER-FOLD SEAT MOTOR AND CIRCUITS FOR AN OPEN
- Disconnect: PFSM C4250C.
- Measure the resistance between PFSM C4250C-8, circuit CPS42 (BU/WH), harness side and PFSM C4250C-9, circuit CPS43 (GN/WH), harness side. Typical motor resistance is 1.5 ohms.
- Is the resistance less than 5 ohms?
Yes
GO to AK7.
No
GO to AK6.
-------------------------------------------------
AK6 CHECK THE POWER-FOLD SEAT MOTOR CIRCUITS FOR AN OPEN
- Remove the backrest latch outer cover to gain access to the LH power-fold seat motor electrical connector. Refer to Seat - Exploded View, Third Row Seat - Exploded View, Third Row.
- Disconnect: LH Power-Fold Seat Motor C4245.
- Measure the resistance between:
- PFSM C4250C-8, circuit CPS42 (BU/WH), harness side and LH power-fold seat motor C4245-3, circuit CPS44 (GY/BN), harness side.
- PFSM C4250C-9, circuit CPS43 (GN/WH), harness side and LH power-fold seat motor C4245-1, circuit CPS45 (VT/OG), harness side.
- Are the resistances less than 5 ohms?
Yes
INSTALL a new power-fold seat motor. REFER to Power-Fold Seat Motor - Third Row Power-Fold Seat Motor - Third Row. TEST the system for normal operation.
No
REPAIR the affected circuit(s). TEST the system for normal operation.
-------------------------------------------------
AK7 CHECK THE PFSM FOR OUTPUT VOLTAGE TO THE FOLD SENSOR
- Connect: PFSM C4250C.
- Verify the vehicle is in PARK and the liftgate is open.
- Verify the courtesy lights are on. If needed, close and open any door on the vehicle.
- Measure the voltage between PFSM C4250C-3, circuit LPS12 (BN/WH) and PFSM C4250C-6, circuit RPS12 (YE/VT), by back-probing the connector.
- Is the voltage greater than 5 volts?
Yes
GO to AK10.
No
GO to AK8.
-------------------------------------------------
AK8 CHECK THE FOLD SENSOR AND CIRCUIT FOR A SHORT TO GROUND
- Disconnect: PFSM C4250C.
- Measure the resistance between PFSM C4250C-3, circuit LPS12 (BN/WH), harness side and ground.
- Is the resistance greater than 10,000 ohms?
Yes
GO to AK11.
No
GO to AK9.
-------------------------------------------------
AK9 CHECK THE FOLD SENSOR CIRCUIT FOR A SHORT TO GROUND
- Remove the backrest latch outer cover to gain access to the power-fold seat motor electrical connector. Refer to Seat - Exploded View, Third Row Seat - Exploded View, Third Row.
- Disconnect: LH Power-Fold Seat Motor C4245.
- Measure the resistance between PFSM C4250C-3, circuit LPS12 (BN/WH), harness side and ground.
- Is the resistance greater than 10,000 ohms?
Yes
INSTALL a new power-fold seat motor assembly. REFER to Power-Fold Seat Motor - Third Row Power-Fold Seat Motor - Third Row. TEST the system for normal operation.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
AK10 CHECK THE FOLD SENSOR CIRCUITS FOR AN OPEN
- Remove the backrest latch outer cover to gain access to the power-fold seat motor electrical connector. Refer to Seat - Exploded View, Third Row Seat - Exploded View, Third Row.
- Disconnect: LH Power-Fold Seat Motor C4245.
- Disconnect: PFSM C4250C.
- Measure the resistance between:
- PFSM C4250C-3, circuit LPS12 (BN/WH), harness side and LH power-fold seat motor C4245-2, circuit LPS78 (VT), harness side.
- PFSM C4250C-6, circuit RPS12 (YE/VT), harness side and LH power-fold seat motor C4245-4, circuit RPS77 (BN/GN), harness side.
- Are the resistances less than 5 ohms?
Yes
INSTALL a new power-fold seat motor assembly. REFER to Power-Fold Seat Motor - Third Row Power-Fold Seat Motor - Third Row. TEST the system for normal operation.
No
REPAIR the affected circuit(s). TEST the system for normal operation.
-------------------------------------------------
AK11 CHECK PFSM CONNECTORS AND PINS FOR DAMAGE AND RETEST THE SYSTEM
- Inspect the PFSM connectors for corrosion and pushed out or damaged pins and repair as necessary.
- Reconnect all the PFSM connectors.
- Operate the seats and determine if the concern is still present.
- Is the concern still present?
Yes
INSTALL a new PFSM. Refer to Power-Fold Seat Module (PFSM) Power-Fold Seat Module (PFSM). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
-------------------------------------------------