Installation
Front Seat Cushion Cover Removal and Installation
Installation
SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.
NOTE: Steps 1-7 show installing the passenger's side, steps 8-17 show installing the driver's side.
1. Front Seat Cushion Cover - Passenger's Side
NOTE: Replace all of the upholstery rings (A) fastening the seat cushion cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D).
Leather Seat
Fabric Seat
1. Install the seat cushion cover (A) with the upholstery rings (B).
2. Install the hook strips (A) to the seat cushion pad (B).
2. Front Seat Cushion - Passenger's Side
1. Install the seat cushion cover/pad (A) on the seat frame (B).
2. Install the hook strips (A) to under the seat cushion.
3. Install the hook strips (A), then install the clip (B).
4. With seat heater: Install the holders (A).
5. With seat heater: Install the harness clip (B).
6. With seat heater: Connect the connecters (C).
7. Install the elastic strap (A) to the seat cushion frame springs (B).
3. Front Seat Center Cover - Passenger's Side
1. Install the center cover (A) to the recline inner cover (B). Make sure the tabs (C) snap into place securely.
4. Front Seat Recline Cover - Passenger's Side
1. Install the hook (A) and clip (B) of the recline cover (C).
2. Install the hooks (D) to the recline inner cover (E).
3. Install the hooks (F) of the recline cover to the recline inner cover.
4. Install the recline knob (G) and screw (H).
5. Front Seat Assembly - Passenger's Side
Without Woofer
With Woofer
1. Connect the connectors (A).
2. Install the harness clip (B).
Front Side
Rear Side
3. Install the seat mounting bolts (A).
NOTE:
* Tighten the bolts by hand first, then tighten them to the specified torque.
* Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat all the way back and tighten bolts 1 and 2, then slide it forward and tighten bolts 3 and 4.
4. Install rear inner seat track end cover (A) and rear outer seat track end cover (B). Make sure the hooks (C) snap into place securely.
6. Head Restraint - Passenger's Side
1. Insert the head restraint (A) into the seat-back as shown.
7. Front Seat Belt Lower Anchor Bolt - Passenger's Side
1. Install the lower anchor bolt (A).
2. Install the anchor cover (A). Make sure the hooks (B) and the tab (C) snap into place securely.
8. Front Seat Cushion Cover - Driver's Side
NOTE: Replace all of the upholstery rings (A) fastening the seat cushion cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D).
Leather Seat
Fabric Seat
1. Install the seat cushion cover (A) with the upholstery rings (B).
2. Install the hook strips (A) to the seat cushion pad (B).
9. Front Seat Cushion - Driver's Side
1. Install the seat cushion cover/pad (A) on the seat frame (B).
Power Seat
Manual Seat
2. Install the hook strips (A) under the seat cushion.
Power Seat
Manual Seat
3. Install the hook strips (A) to both sides of the seat cushion frame.
4. Install the clip (B) to the seat cushion frame.
With Seat Heater
5. With seat heater: Connect the connectors (A).
6. With seat heater: Install the harness clip (B).
7. With seat heater: Install the holders (C) to the seat cushion frame springs (D).
8. Install the elastic strap (A) to the seat cushion frame springs (B).
10. Front Seat Center Cover - Driver's Side
Power Seat
1. Install the upper center inner cover (A).
2. Install the center cover (B). Make sure the tabs (C) snap into place securely.
3. Install the screw (D).
Manual Seat
1. Install the center cover (A) to the recline inner cover (B). make sure the tabs (C) snap into place securely.
11. Front Seat Recline Cover - Driver's Side
Power Seat
1. Install the upper center inner cover (A) to the recline cover (B).
2. Connect the connector, then install the wire harness (C) to the hooks (D).
3. Install the clip (E) and tabs (F), then install the recline cover.
4. Install the tabs (G), then install the screw (H).
Manual Seat
1. Install the hook (A) and clip (B) of the recline cover (C).
2. Install the hooks (D) to the recline inner cover (E).
3. Install the hook (F) of the recline cover to the recline inner cover.
4. Install the recline knob (G) and screw (H).
12. Front Seat Height Adjuster Handle - Manual Seat
1. Install the height adjuster handle (A) and the screws (B).
2. Install the cap (C). Make sure the hooks (D) snap into place securely.
13. Front Cover - Power Seat
1. Install the tabs (A), set the pin (B), and install the hook (C), then install the front cover (D). Make sure the hooks snap into place securely.
14. Front Seat - Driver's Side
1. Connect the connectors (A).
2. Install the harness clip (B).
Front Side
Rear Side
3. Install the seat mounting bolts (A).
NOTE:
* Tighten the bolts by hand first, then tighten them to the specified torque.
* Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat all the way back and tighten bolts 1 and 2, then slide it forward and tighten bolts 3 and 4.
4. Install rear inner seat track end cover (A) and rear outer seat track end cover (B). Make sure the hooks (C) snap into place securely.
15. Head Restraint - Driver's Side
1. Insert the head restraint (A) to the seat-back as shown.
16. Battery Terminal (SRS) - Reconnection
NOTE: If the battery performance is abnormal, test the battery.
1. Clean the battery terminals.
2. Connect the positive cable (A) to the battery.
NOTE: Always connect the positive side first.
3. Connect the negative cable (B) to the battery.
4. Apply multipurpose grease to the terminals to prevent corrosion.
17. Front Seat Belt Lower Anchor Bolt
1. Install the lower anchor bolt.
NOTE: Before installing the anchor bolt, make sure there are no twists or kinks in the seat belt.
2. Install the anchor cover (A). Make sure the hooks (B) and the tab (C) snap into place securely.