Operation CHARM: Car repair manuals for everyone.
Home >> Honda >> 2012 >> CR-V 4WD L4-2.4L >> Repair and Diagnosis >> Transmission and Drivetrain >> Transfer Case >> Service and Repair >> Overhaul >> Transfer Shaft Assembly O-Ring Replacement

Transfer Shaft Assembly O-Ring Replacement






Transfer Shaft Assembly O-Ring Replacement

Removal

1. Vehicle Lift

1. Raise the vehicle on a lift, and make sure it is securely supported.

2. Front Splash Shield





1. Remove the bolts (A), then remove the clips (B) that secure the front inner fender and the front splash shield (C) to the body.

2. From under the front bumper (D), remove the clips (E).

3. From under the body, remove the clips (F), then pull out the front splash shield.

3. Front Floor Undercover





1. Remove the bolts (A) and the clips (B, C) securing the front floor undercover (D), then remove the front floor undercover.

4. ATF - Replacement





1. Remove the drain plug (A), and drain the ATF.

2. Reinstall the drain plug using a new sealing washer (B).

5. Under-Floor TWC Assembly





1. Remove the under-floor TWC.

6. Propeller Shaft Transmission Side - Disconnection





1. Make reference mark (A) across the No. 1 propeller shaft (B) and the transfer companion flange (C).

2. Separate the No. 1 propeller shaft from the transfer companion flange.

NOTE: Suspend the propeller shaft with an appropriate size nylon strap.

7. Transfer Assembly





1. Remove the transfer assembly (A) and the dowel pin (B).

2. Remove the O-ring (C) from the transfer assembly.

8. Transfer Shaft O-Ring





1. Remove the transfer shaft assembly (A) and the dowel pin (B).





2. Remove the O-ring (A).

Installation

1. Transfer Shaft O-Ring





1. Install a new O-ring (A).





2. Install the transfer shaft assembly (A) and the dowel pin (B).

2. Transfer Assembly





1. Install a new O-ring (A) on the transfer assembly (B).

2. Install the transfer assembly and the dowel pin (C).

3. Propeller Shaft Transmission Side - Reconnection





1. Set the No. 1 propeller shaft (A) to the transfer companion flange (B) by aligning the reference mark (C) you made during the removal procedure. Then install new flange bolts (D) to the specified torque.

4. Under Floor TWC Assembly





1. Install the under-floor TWC.

5. Front Floor Undercover





1. Install the front floor undercover (A), then install the bolts (B) and the clips (C, D). Make sure the clips snap into place securely.

6. Front Splash Shield





1. Install the front splash shield (A), then install the bolts (B) and the clips (C, D). Make sure the clips snap into place securely.

7. ATF - Replacement





1. Remove the ATF dipstick (yellow loop) (A), and wipe it with a clean cloth.





2. Refill the transmission with the recommended fluid into the dipstick guide tube opening (A) to bring the fluid level between the upper mark and the lower mark of the dipstick. Always use ATF DW-1 (genuine Honda automatic transmission fluid). Using a non-Honda ATF can affect shift quality.












3. Insert the dipstick (A) into the guide tube aligning the notch (B) with the guide tab (C).





4. Remove the dipstick.

5. Make sure the fluid level is between the upper mark (A) and the lower mark (B) on the dipstick.

6. Insert the dipstick into the guide tube aligning the notch with the guide tab.

8. Warm Up The Engine

1. Start the engine. Hold the engine speed at 3,000 rpm without load in P or N until the radiator fan comes on.

2. Park the vehicle on level ground.

3. Turn the ignition switch to LOCK (0).

9. ATF Level Check





NOTE:
* Keep all foreign particles out of the transmission.
* Check the fluid level within 60-90 seconds after turning the engine off.
* Higher fluid level may be indicated if the radiator fan comes on twice or more.

1. Remove the ATF dipstick (yellow loop) (A), and wipe it with a clean cloth.

2. Insert the dipstick into the guide tube aligning the notch (B) with the guide tab (C).





3. Remove the dipstick, and check the ATF level. It should be between the upper mark (A) and the lower mark (B).

4. If the ATF level is below the lower mark, check for fluid leaks at the transmission, the hoses, and the line joints. If a problem is found, fix it before filling the transmission with ATF.

NOTE: If the vehicle is driven when the ATF level is below the lower mark, one or more of these symptoms may occur:
* Transmission damage.
* Vehicle does not move in any gear.
* Vehicle accelerates poorly, and engine revs up abnormally high when starting off in forward and reverse positions.
* Engine vibrates at idle.

5. If the ATF level is above the upper mark, drain the ATF to proper level.

NOTE: If the vehicle is driven when the ATF level is above the upper mark, the vehicle may creep forward while in N, or have shifting problems.





6. If necessary, fill the transmission with ATF through the dipstick guide tube opening (A) to bring the fluid level between the upper mark and the lower mark of the dipstick. Do not fill the fluid above the upper mark. Always use ATF DW-1 (genuine Honda automatic transmission fluid). Using a non-Honda ATF can affect shift quality.

7. Insert the dipstick into the guide tube aligning the notch with the guide tab.

10. HDS DLC - Connection





1. Connect the HDS to the data link connector (DLC) (A) located under the driver's side of the dashboard.

2. Turn the ignition switch to ON (II).

3. Make sure the HDS communicates with the vehicle. If it does not communicate, go to the DLC circuit troubleshooting.

11. Maintenance Minder Reset

1. Reset the Maintenance Minder. Description and Operation
pro multis · About Operation CHARM