Removal and Installation
Curtain Shield Airbag Assembly:
REMOVAL
NOTE:
- If the wiring connector of the SRS is disconnected and the ignition switch is at ON position, DTCs will be recorded.
- Never use the airbag parts from another vehicle. When replacing parts, replace them with new parts.
1. REMOVE FRONT SEAT
a. Remove the 4 seat track covers and 4 bolts.
b. Disconnect the connectors.
NOTE: When handling the airbag connector, take care not to damage the airbag wire harness.
c. Remove the front seat.
NOTE: Be careful not to damage the body.
2. REMOVE HEADREST
3. REMOVE SEATBACK BOARD
Remove the seatback board as shown in the illustration.
HINT: Remove the seatback board in order "A" and "B" as shown in the illustration.
4. REMOVE SEAT CUSHION OUTER SHIELD
a. Remove the 4 screws.
b. Disconnect the connectors.
c. Remove the seat cushion outer shield.
5. REMOVE FRONT SEAT INNER BELT
a. Remove the clump, then disconnect the connector.
b. Remove the bolt and inner belt.
6. REMOVE SEAT CUSHION INNER SHIELD
Remove the 3 screws and seat cushion inner shield.
7. REMOVE LOWER SEAT CUSHION SHIELD
Remove the screw and lower seat cushion shield as shown in the illustration.
8. REMOVE FRONT SEAT CUSHION SHIELD
Remove the screw and front seat cushion shield.
9. REMOVE SEAT CUSHION ASSEMBLY
a. Remove the 4 bolts.
b. Remove the clamps from the seat cushion assembly.
10. REMOVE SEATBACK ASSEMBLY
a. Remove the hog rings.
b. Disengage the hook as shown in the illustration.
c. Disconnect the connectors.
d. Remove the 4 bolts and seatback assembly.
NOTE: When handling the airbag connector take care not to damage the airbag wire harness.
e. Remove the screw and RH reclining adjuster inside shield, then disconnect the side airbag connector.
NOTE: When handling the airbag connector take care not to damage the airbag wire harness.
11. REMOVE ARMREST
12. REMOVE SEATBACK FRAME
a. Remove the hog rings, the clamps and the 2 bolts.
b. Remove the 2 headrest supports.
c. Remove the seatback frame from the seatback cover with pad
13. REMOVE LUMBER SUPPORT
Remove the 2 bolts and lumber support
INSTALLATION
NOTE: Never use airbag parts from another vehicle. When replacing parts, replace them with new parts.
1. INSTALL LUMBER SUPPORT
Install the lumber support with the 2 bolts.
2. INSTALL SEATBACK FRAME
a. Install the seatback cover to the seatback frame.
b. Install new hog rings, clamps and the 2 bolts.
Torque: 4.7 N.m (48 kgf.cm, 42 in.lbf)
c. Install the 2 headrest supports.
3. INSTALL SEATBACK ASSEMBLY
a. Place the airbag connector along the inner seat adjuster, and then install the RH reclining adjuster inside shield with a screw so that the connector is placed in between.
b. Install the seatback assembly with the 4 bolts.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
NOTE:
- Make sure that the seatback assembly is installed to the specified torque.
- If the seatback assembly has been dropped, or there are cracks, dents or other defects in the case or connector, replace the seatback assembly with a new one.
- When installing the seat back assembly, take care it is not to be pinched between other parts.
c. Install new hog rings.
d. Hang the hook.
e. Connect the connectors.
4. INSTALL ARMREST
Torque: 37 N.m (380 kgf.cm, 27 ft.lbf)
5. INSTALL HEADREST
6. INSTALL SEAT CUSHION ASSEMBLY
a. Install the seat cushion assembly with the 4 bolts.
Torque: 21 N.m (210 kgf.cm, 15 ft.lbf)
b. Engage the wire harness clamp.
7. INSTALL FRONT SEAT CUSHION SHIELD
Install the seat cushion shield with the screw.
8. INSTALL LOWER SEAT CUSHION SHIELD
Install the lower seat cushion shield with the screws.
9. INSTALL FRONT SEAT INNER BELT
a. Engage the clamp, then connect the connector.
b. Install the inner belt with the bolt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
10. INSTALL SEAT CUSHION OUTER SHIELD
a. Connect the connectors.
b. Install the seat cushion outer shield with the 3 screws.
11. INSTALL SEATBACK BOARD
12. INSTALL FRONT SEAT
a. Install the front seat.
NOTE: Be careful not to damage body
b. Connect the connectors.
c. Install the 4 bolts.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
d. Install the 4 seat track covers.