ON-BOARD DIAGNOSTIC TEST [WL-C, WE-C (Thailand, General (L.H.D. R.H.D.) specs.)]

id0102b0801000

DTC Reading Procedure

1.  Connect the M-MDS to the DLC‐2.

dbg110bwba01

2.  After the vehicle is identified, select the following items from the initial screen of the M-MDS.

•  When using the IDS (notebook PC)

1.  Select the “Toolbox” tab.

2.  Select “SelfTest”.

3.  Select “Module”.

4.  Select “PCM”.

•  When using the PDS (pocket PC)

1.  Select “Module Tests”.

2.  Select “PCM”.

3.  Select “SelfTest”.

3.  Then, select the “Retrieve CMDTCs” and perform procedures according to directions on the M-MDS screen.

4.  Verify the DTC according to the directions on the M-MDS screen.

•  If any DTCs are displayed, perform troubleshooting according to the corresponding DTC inspection.

5.  After completion of repairs, clear all DTCs stored in the PCM, while referring to “AFTER REPAIR PROCEDURE“.

Pending Trouble Code Access Procedure

1.  Connect the M-MDS to the DLC‐2.

dbg110bwba01

2.  After the vehicle is identified, select the following items from the initial screen of the M-MDS.

•  When using the IDS (notebook PC)

1.  Select the “Toolbox” tab.

2.  Select “SelfTest”.

3.  Select “Module”.

4.  Select “PCM”.

•  When using the PDS (pocket PC)

1.  Select “Module Tests”.

2.  Select “PCM”.

3.  Select “SelfTest”.

3.  Then, select the “Retrieve CMDTCs” and perform procedures according to directions on the M-MDS screen.

4.  Retrieve the pending trouble codes according to the directions on the M-MDS screen.

Freeze Frame PID Data Access Procedure

1.  Connect the M-MDS to the DLC‐2.

dbg110bwba01

2.  After the vehicle is identified, select the following items from the initial screen of the M-MDS.

•  When using the IDS (notebook PC)

1.  Select the “Toolbox” tab.

2.  Select “SelfTest”.

3.  Select “Module”.

4.  Select “PCM”.

•  When using the PDS (pocket PC)

1.  Select “Module Tests”.

2.  Select “PCM”.

3.  Select “SelfTest”.

3.  Then, select the “Retrieve CMDTCs” and perform procedures according to directions on the M-MDS screen.

4.  Retrieve the freeze frame PID data according to the directions on the M-MDS screen.

PID/DATA Monitor and Record Procedure

Note

•  The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device. If a monitored value of an output device is out of specification, inspect the monitored value of the input device related to the output control.

1.  Connect the M-MDS to the DLC‐2.

dbg110bwba01

2.  After the vehicle is identified, select the following items from the initial screen of the M-MDS.

•  When using the IDS (notebook PC)

1.  Select the “Toolbox” tab.

2.  Select “DataLogger”.

3.  Select “Module”.

4.  Select “PCM”.

•  When using the PDS (pocket PC)

1.  Select “Module Tests”.

2.  Select “PCM”.

3.  Select “DataLogger”.

3.  Select the PID from the PID table.

4.  Verify the PID data according to the directions on the screen.

Simulation Function Procedure

1.  Connect the M-MDS to the DLC‐2.

dbg110bwba01

2.  After the vehicle is identified, select the following items from the initial screen of the M-MDS.

•  When using the IDS (notebook PC)

1.  Select the “Toolbox” tab.

2.  Select “DataLogger”.

3.  Select “Module”.

4.  Select “PCM”.

•  When using the PDS (pocket PC)

1.  Select “Module Tests”.

2.  Select “PCM”.

3.  Select “DataLogger”.

3.  Select the simulation items from the PID table.

4.  Perform the simulation function, inspect the operations for each parts.

•  If there is no operation sound from the relay, motor, and solenoid after the simulation function inspection is performed, it is possible that there is an open or short circuit in the wiring harness, relay, motor or solenoid, or sticking and operation malfunction.