PCM INSPECTION [F2]

id014094802500


Using M-MDS

Note
•  PIDs for the following parts are not available on this model. Go to the appropriate part inspection page.
―  CMP sensor
―  Main relay

1.  Connect the M-MDS to the DLC-2.

arnffw00001189

2.  Turn the ignition switch to ON position.

3.  Measure the PID value.

•  If PID value is not within the specification, follow the instructions in “Inspection item (s)” column.
Note
•  The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device. If a monitored value of an output device is out of specification, inspect the monitored value of the input device related to the output control.
•  For input/output signals except those of the monitoring items, use a voltmeter to measure the PCM terminal voltage.
•  The simulation items that are used in the ENGINE CONTROL SYSTEM OPERATION INSPECTION are as follows.
―  ACCS, EVAPCP, FP, FPRC, FUELPW1, IAC, INJ 1, INJ 2

PID MONITOR Table

Monitor item (Definition)

Unit/Condition

Condition/Specification (Reference)

Inspection item (s)

PCM terminal
ACCS
(A/C relay)
On/Off
•  Ignition switch on:Off
•  A/C switch on and fan switch on at idle:On
•  The following PIDs
―  RPM
―  TP
―  ECT
―  ACSW
•  A/C relay
1J
ACSW
(A/C switch)
On/Off
•  A/C switch and fan switch on at ignition switch on: On
•  A/C switch off at ignition switch on: Off
•  A/C switch
1Q
ARPMDES
(Target engine speed)
RPM
•  Indicate the target engine speed
•  CMP sensor
—
BARO
(Barometric pressure)
Kpa
•  Below 400 m {0.25 mile} above sea level:100—103kPa {1.01—10.5 kgf/cm2}
•  DTCP1195 is indicated.
follow DTC Troubleshooting
—
V
•  Below 400 m {0.25 mile} abovesea level:3.9—4.0V
BOO
(Brake switch)
On/Off
•  Brake pedal depressed:On
•  Brake pedal released:Off
•  Brake switch
1O
CPP/PNP
(Shift lever position)
Drive/Neutral
•  Neutral:Neutral
•  Other than neutral:Drive
•  Neutral switch
1V
ECT
(Engine coolant temperature)
°C
°F
•  Indicate the ECT
•  ECT sensor
2Q
V
•  Ignition switch to the ON position (after warm up):0.58 V
EVAPCP
(Purge solenoid valve duty value)
%
•  Ignition swich on:0%
•  Idle:0%
•  The following PIDs
―  IAT
―  RPM
―  ECT
―  MAF
―  TP
―  O2S11
―  VPWR
2X
FP
(Fuel pump relay)
On/Off
•  Ignition swich on:Off
•  Idle:On
•  Cranking:On
•  The following PIDs
―  RPM
•  Fuel pump relay
1H
FPRC
(PRC solenoid valve)
On/Off
•  Ignition swich on:Off
•  Idle:Off
•  Engine start at hot condition:On
•  The following PIDs
―  IAT
―  RPM
―  ECT
―  TP
―  VPWR
•  PRC solenoid valve
2T
FUELPW1
(Fuel injector)
ms
•  Ignition switch on:0.0ms
•  Idle:3.0—5.0ms
•  The following PIDs
―  IAT
―  RPM
―  ECT
―  MAF
―  TP
―  O2S11
―  VPWR
―  PSP
―  BOO
―  ACSW
•  CMP sensor
2U, 2V
IAC
(IAC valve control)
ms
•  Idle:2.4—2.7ms
•  The following PIDs
―  IAT
―  RPM
―  ECT
―  MAF
―  TP
―  PSP
―  ACSW
―  Test
―  CPP/PNP
•  IAC valve
2W
IAT
(Intake air temperature)
°C
°F
•  Indicate the IAT
•  IAT sensor
2L
V
•  IAT 20 °C {68 °F}:2.15 V
IDLE_SW
(Idle switch)
Idle/Off Idle
•  Accelerator depressed:Off idle
•  Accelerator released:Idle
•  Idle switch
1N
LOAD
(Engine load)
%
•  Indicate the engine load
—
—
LONGFT1
(Long term fuel trim)
%
•  Indicate the long term fuel trim
—
—
MAF
(Mass air flow)
g/s
•  Indicate the MAF amount
•  MAF sensor
2O
V
•  Ignition switch to the ON position:1.45 V
•  Idle (after warm up):2.15 V
MIL
(Malfunction indicator)
On/Off
•  Indicate that the engine control system malfunction accurs
Perform applicable DTC troubleshooting
—
O2S11
(O2S)
V
•  Ignition switch on:0—1.0V
•  Idle (After warm up):0—1.0V
•  Acceleration (After warm up):0.5—1.0V
•  Deceleration (After warm up):0—0.5V
•  O2S
2N
PSP
(PSP switch)
High/Low
•  Steering wheel fully turned:High
•  Steering wheel straight ahead position:Low
•  PSP switch
1P
RPM
(Engine speed)
RPM
•  Indicate engine speed
•  CMP sensor
—
SELTESTDTC
(Diagnostic trouble codes)
—
—
Perform applicable DTC troubleshooting
—
SHRTFT1
(Short term fuel trim)
%
•  Indicate the short term fuel trim
—
—
SPARKADV
(Ignition timing)
°
•  Indicate the ignition timing
•  The following PIDs
―  MAF
―  IAT
―  RPM
―  TP
―  ECT
―  PSP
―  CPP/PNP
―  ACSW
―  Test
•  CMP sensor
•  Idle speed and ignition timing
2E
Test
(Test mode)
ON/OFF
•  Test mode On:ON
•  Test mode Off:OFF
—
—
TP
(TP sensor)
V
•  Closed throttle position:0.4—0.6 V
•  Wide open throttle:3.4—4.7 V
•  TP sensor
2M
VPWR
(Battery positive voltage)
V
•  Under any condition:B+
•  Battery
1A
VSS
(Vehicle speed)
KPH
•  Vehicle speed 20 km/h {mph}:20 km/h {mph}
•  Vehicle speed 40 km/h {mph}:40 km/h {mph}
•  VSS
1M


Without Using the M-MDS

Caution
•  The PCM terminal voltages vary with change in measuring conditions and vehicle conditions. Always carry out a total inspection of the input systems, and PCM to determine the cause of trouble. Otherwise, a wrong diagnosis will be made.

1.  Remove the PCM.

2.  Reconnect PCM connector and battery negative terminal.

Note
•  With the PCM connector connected, body ground the voltmeter negative ( - ) lead and measure voltage at each PCM terminal by inserting the voltmeter positive ( + ) lead.

3.  Measure the voltage at each terminal.

•  If any incorrect voltage is detected, inspect the related system(s), witing harnesses and connector(s) referring to the Action column in the terminal voltage table.


Terminal voltage table (Reference)

absggw00000828

Terminal

Signal

Connected to

Test condition

Voltage (V)

Inspection item
1A
Back-up power supply
Battery
Under any condition
B+
•  Battery
•  Related wiring harness
1B
Power supply
Main relay
Ignition switch off
1.0 or less
•  Related wiring harness
Ignition switch to the ON position
B+
1C
—
—
—
—
—
1D
Serial communication
DLC (Terminal KLN)
Because of this terminal is for serial communication, good/no good judgment by terminal voltage is not possible. Carry out inspection according to DTCs.
—
—
1E
 
DTC output
 
DLC (Terminal FEN)
Ignition switch to the ON position and terminal TEN (in DLC) short to chassis ground
Not DTC stored
1.0 or less
•  Related wiring harness
DTC stored
0—B+
DLC-2 (Terminal KLN)
Because of this terminal is for serial communication, good/no good judgment by terminal voltage is not possible. Carry out inspection according to DTCs.
—
—
1F
—
—
—
—
—
1G
—
—
—
—
—
1H
Fuel pump control
Fuel pump relay
Ignition switch to the ON position
B+
•  Fuel pump relay
•  Related wiring harness
Cranking
1.0 or less
Idle
1I
—
—
—
—
—
1J
A/C control
A/C relay
A/C not operating
B+
•  A/C relay
•  Related wiring harness
A/C operating
1.0 or less
1K
Diagnostic test mode
DLC (Terminal TEN)
Ignition switch to the ON position
Terminal TEN (DLC) open
B+
•  Related wiring harness
Terminal TEN (DLC) short to ground
1.0 or less
1L
—
—
—
—
—
1M
Vehicle speed
VSS
Vehicle stopped
0 or Approx. 5.0
•  VSS
•  Related wiring harness
Vehicle running
Approx. 5.0
1N
CTP
CTP switch
Ignition switch to the ON position
Accelerator pedal depressed
B+
•  CTP switch
•  Related wiring harness
Accelerator pedal released
1.0 or less
1O
Brake
Brake switch
Brake pedal depressed
B+
•  Brake switch
•  Related wiring harness
Brake pedal released
1.0 or less
1P
PSP
PSP switch
Idle
Steering wheel at straight ahead position
B+
•  PSP switch
•  Related wiring harness
While turning steering wheel
1.0 or less
1Q
A/C
A/C switch
Ignition switch to the ON position
A/C switch and fan switch on
1.0 or less
•  A/C switch
•  Related wiring harness
A/C switch off
B+
1R
—
—
—
—
—
1S
—
—
—
—
—
1T
—
—
—
—
—
1U
—
—
—
—
—
1V
Load/no load distinction
Neutral/clutch switch
Ignition switch to the ON position
Transmission neutral position or clutch pedal depressed
1.0 or less
•  Neutral switch
•  Clutch switch
•  Related wiring harness
Other than transmission neutral and clutch pedal released
B+
2A
Fuel injector ground
Ground
Under any condition
1.0 or less
•  Related wiring harness
2B
Power ground
Ground
Under any condition
1.0 or less
•  Related wiring harness
2C
System ground
Ground
Under any condition
1.0 or less
•  Related wiring harness
2D
Internal ground
MAF sensor, IAT sensor, ECT sensor, O2S, TP sensor
Under any condition
1.0 or less
•  Related wiring harness
2E
CMP
CMP sensor (integrated into distributor)
Ignition switch to the ON position
5.0
•  CMP sensor
•  Related wiring harness
Idle
1.8—2.3
2F
IGT control
Igniter
Ignition switch to the ON position
1.0 or less
•  Ignition control module
•  Related wiring harness Related wiring harness
Idle
0.35—0.5
2G
—
—
—
—
—
2H
—
—
—
—
—
2I
—
—
—
—
—
2J
—
—
—
—
—
2K
Constant voltage (Vref)
TP sensor
Ignition switch to the ON position
4.5—5.5
•  Related wiring harness
2L
IAT
IAT sensor
Ignition switch to the ON position
IAT 20 °C {68 °F}
2.15
•  IAT sensor
•  Related wiring harness
2M
TP
TP sensor
Ignition switch to the ON position
APP is released
0.4—0.6
•  TP sensor
•  Related wiring harness
APP is depressed
3.4—4.7
2N
O2S
O2S
Ignition switch to the ON position
0.55
•  O2S
•  Related wiring harness
Idle
Engine cold
0.0—1.0
After warm up
0.0—1.0
Acceleration
0.5—1.0
Deceleration
0.0—0.5
2O
MAF
MAF sensor
Ignition switch to the ON position
1.45
•  MAF sensor
•  Related wiring harness
Idle (after warm up)
2.15
2P
—
—
—
—
—
2Q
ECT
ECT sensor
Ignition switch to the ON position
IAT 20 °C {68 °F}
1.02
•  ECT sensor
•  Related wiring harness
After warm up
0.58
2R
—
—
—
—
—
2S
—
—
—
—
—
2T
Pressure regulator control
PRC solenoid valve
Idle (after warm up)
B+
•  PRC solenoid valve
•  Related wiring harness
2U
Fuel injector control
Fuel injector No.1, No.3
Ignition switch to the ON position
B+
•  Fuel injector
•  Related wiring harness
Idle
B+
2V
Fuel injector No.2, No.4
Ignition switch to the ON position
B+
•  Fuel injector
•  Related wiring harness
Idle
B+
2W
IAC
IAC valve
Ignition switch to the ON position
0.2
•  IAC valve
•  Related wiring harness
Idle (after warm up)
Approx. 1.0
2X
Purge control
Purge solenoid valve
Ignition switch to the ON position
B+
•  Purge solenoid valve
•  Related wiring harness
Idle
B+
2Y
—
—
—
—
—