BASIC POWER WINDOW SYSTEM INSPECTION [POWER WINDOW SYSTEMS (WITH AUTO-OPEN/CLOSE FUNCTION FOR DRIVER-SIDE)]

STEP	INSPECTION	ACTION
1	• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position. • Operate the power window using the manual open/close function on the power window main switch. • Does the power window operate properly?	Yes	Go to the next step.
No	• Inspect the power window main switch and the wiring harness. • Repair or replace malfunctioning part.
2	• Set the power cut switch to the UNLOCK position. • Operate the power window using the power window subswitch. • Does the power window operate properly?	Yes	Go to the next step.
No	• Inspect for the power window subswitch and the wiring harness. • Repair or replace malfunctioning parts.
3	• Set the power cut switch to the LOCK position. • Operate all power windows other than the driver side. • Does the power window operate ?	Yes	• Inspect the power cut switch and the wiring harness. • Replace the power window main switch.
No	• Manual mode function is normal. • Perform the automatic mode function inspection.

STEP

INSPECTION

ACTION

• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position.

• Operate the power window using the manual open/close function on the power window main switch.

• Does the power window operate properly?

Yes

Go to the next step.

• Inspect the power window main switch and the wiring harness.

• Repair or replace malfunctioning part.

• Set the power cut switch to the UNLOCK position.

• Operate the power window using the power window subswitch.

• Does the power window operate properly?

Yes

Go to the next step.

• Inspect for the power window subswitch and the wiring harness.

• Repair or replace malfunctioning parts.

• Set the power cut switch to the LOCK position.

• Operate all power windows other than the driver side.

• Does the power window operate ?

Yes

• Inspect the power cut switch and the wiring harness.

• Replace the power window main switch.

• Manual mode function is normal.

• Perform the automatic mode function inspection.

STEP	INSPECTION	ACTION
1	• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position. • Operate the power window using the auto open /close function on the power window main switch. • Does the power window operate properly?	Yes	Go to the next step.
No	If the power window automatically opens in the closing operation: • Go to NO.6 THE DRIVER'S SIDE POWER WINDOW AUTOMATICALLY OPENS IN THE CLOSING OPERATION [POWER WINDOW SYSTEMS (WITH AUTO-OPEN/CLOSE FUNCTION FOR DRIVER-SIDE)] Others: • Go to No.1 THE AUTO OPEN/CLOSE FUNCTION ON THE DRIVER'S SIDE POWER WINDOW IS INOPERATIVE [POWER WINDOW SYSTEMS (WITH AUTO-OPEN/CLOSE FUNCTION FOR DRIVER-SIDE)]
2	• Operate the power window main switch to the close position while the power window is in opening operation. • Is the power window operation stopped?	Yes	Go to the next step.
No	• Replace the power window main switch. (power window control unit is malfunctioning.)
3	• Operate the power window main switch to open position while the power window is in closing operation. • Is the power window operation stopped?	Yes	• Automatic mode function is normal. • Perform the IG-OFF timer function inspection.
No	• Replace the power window main switch. (power window control unit is malfunctioning.)

STEP

INSPECTION

ACTION

• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position.

• Operate the power window using the auto open /close function on the power window main switch.

• Does the power window operate properly?

Yes

Go to the next step.

If the power window automatically opens in the closing operation:

• Go to NO.6 THE DRIVER'S SIDE POWER WINDOW AUTOMATICALLY OPENS IN THE CLOSING OPERATION [POWER WINDOW SYSTEMS (WITH AUTO-OPEN/CLOSE FUNCTION FOR DRIVER-SIDE)]

Others:

• Go to No.1 THE AUTO OPEN/CLOSE FUNCTION ON THE DRIVER'S SIDE POWER WINDOW IS INOPERATIVE [POWER WINDOW SYSTEMS (WITH AUTO-OPEN/CLOSE FUNCTION FOR DRIVER-SIDE)]

• Operate the power window main switch to the close position while the power window is in opening operation.

• Is the power window operation stopped?

Yes

Go to the next step.

• Replace the power window main switch. (power window control unit is malfunctioning.)

• Operate the power window main switch to open position while the power window is in closing operation.

• Is the power window operation stopped?

Yes

• Automatic mode function is normal.

• Perform the IG-OFF timer function inspection.

• Replace the power window main switch. (power window control unit is malfunctioning.)

STEP	INSPECTION	ACTION
1	• Close all doors. • Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position.. • In automatic mode, push down the power window main switch for the driver-side front door glass. The door glass should move down within approx. 43s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off. • In manual mode (finger continuously depressing the power window main switch), the door glass should move down within approx. 43s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off. • Does the driver-side front door glass move down?	Yes	• Go to the next step.
No	• If it does not move up and down upon reinspection, inspect the following: ― Wiring harness for the door open/close signal system . ― Latch switch. • Repair or replace the malfunctioning part, and reinspect. ― If operation is not normal, replace the power window main switch, and then go to the next step.
2	• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position • In automatic mode, pull up the power window main switch for the driver-side front door glass. The door glass does not move up within approx. 43s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off. • Verify that driver-side front door glass does not operate • Does the driver-side front door glass move up?	Yes	• If operation is not normal, replace the power window main switch, then go to the next step.
No	• Go to the next step.
3	• Open any doors. • Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position. • Push/pull the power window main switch for the door glass within approx. 43s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off. • Verify that the door glass does not move up or down. • Does the door glass move up or down?	Yes	• Inspect the door switch and related wiring harness. • If above parts are normal, replace the power window main switch, then go to the next step. • If the above parts have any malfunction, repair or replace the malfunction part, then go to the next step.
No	• Go to the next step.
4	• Close all doors. • Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position. • Push/pull the power window main switch for door glass after approx. 60 s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off. • Verify that the door glass does not move up or down. • Does the door glass move up or down?	Yes	• If operation is not normal, replace the power window main switch, then go to the automatic door glass return function inspection.
No	• The IG OFF timer function is normal. • Go to the automatic door glass return function inspection.

STEP

INSPECTION

ACTION

• Close all doors.

• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position..

• In automatic mode, push down the power window main switch for the driver-side front door glass. The door glass should move down within approx. 43s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off.

• In manual mode (finger continuously depressing the power window main switch), the door glass should move down within approx. 43s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off.

• Does the driver-side front door glass move down?

Yes

• Go to the next step.

• If it does not move up and down upon reinspection, inspect the following:

― Wiring harness for the door open/close signal system .

― Latch switch.

• Repair or replace the malfunctioning part, and reinspect.

― If operation is not normal, replace the power window main switch, and then go to the next step.

• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position

• In automatic mode, pull up the power window main switch for the driver-side front door glass. The door glass does not move up within approx. 43s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off.

• Verify that driver-side front door glass does not operate

• Does the driver-side front door glass move up?

Yes

• If operation is not normal, replace the power window main switch, then go to the next step.

• Go to the next step.

• Open any doors.

• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position.

• Push/pull the power window main switch for the door glass within approx. 43s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off.

• Verify that the door glass does not move up or down.

• Does the door glass move up or down?

Yes

• Inspect the door switch and related wiring harness.

• If above parts are normal, replace the power window main switch, then go to the next step.

• If the above parts have any malfunction, repair or replace the malfunction part, then go to the next step.

• Go to the next step.

• Close all doors.

• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position.

• Push/pull the power window main switch for door glass after approx. 60 s after ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch off.

• Verify that the door glass does not move up or down.

• Does the door glass move up or down?

Yes

• If operation is not normal, replace the power window main switch, then go to the automatic door glass return function inspection.

• The IG OFF timer function is normal.

• Go to the automatic door glass return function inspection.

STEP	INSPECTION	ACTION
1	• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position. • Fully open the driver"s side power window. • Set the hammer (thickness: 10 mm or more) as shown below. Then, close the power window using auto close function. • Inspect that the power window opens by 200 mm after contacting the hammer and stops the operation. • Does automatic door glass return function operate properly?	Yes	• Automatic door glass return function is normal. • Perform the two-step down function inspection.
No	Go to the next step.
2	• Does power window open before contacting the hammer?	Yes	• Go to NO.6 THE DRIVER'S SIDE POWER WINDOW AUTOMATICALLY OPENS IN THE CLOSING OPERATION [POWER WINDOW SYSTEMS (WITH AUTO-OPEN/CLOSE FUNCTION FOR DRIVER-SIDE)]
No	• Initialize the power window main switch. Note • Before initializing the power window main switch, cut off the power supply to the power window main switch for 60 seconds. Then, reconnect or install it again after 60 seconds: <Power supply cut-off method> ― Disconnect the negative battery cable from the battery terminal. ― Disconnect the power window main switch connector. ― Remove the fuse for the power window system.

STEP

INSPECTION

ACTION

• Turn the ignition (F2, G6)/engine (WE-C, WL-3, WL-C, WLT-1, WLT-2) switch to the ON position.

• Fully open the driver"s side power window.

• Set the hammer (thickness: 10 mm or more) as shown below. Then, close the power window using auto close function.

• Inspect that the power window opens by 200 mm after contacting the hammer and stops the operation.

• Does automatic door glass return function operate properly?

Yes

• Automatic door glass return function is normal.

• Perform the two-step down function inspection.

Go to the next step.

• Does power window open before contacting the hammer?

Yes

• Go to NO.6 THE DRIVER'S SIDE POWER WINDOW AUTOMATICALLY OPENS IN THE CLOSING OPERATION [POWER WINDOW SYSTEMS (WITH AUTO-OPEN/CLOSE FUNCTION FOR DRIVER-SIDE)]

• Initialize the power window main switch.

Note

• Before initializing the power window main switch, cut off the power supply to the power window main switch for 60 seconds. Then, reconnect or install it again after 60 seconds:

― Disconnect the negative battery cable from the battery terminal.

― Disconnect the power window main switch connector.

― Remove the fuse for the power window system.