| Item |
Specifications |
||
| Engine model |
4JJ3 |
||
| Type |
Diesel, 4-cycle, water-cooled inline DOHC |
||
| Combustion chamber type |
Direct injection type |
||
| Cylinder liner type |
No liner |
||
| Number of cylinders - inner diameter x stroke |
4 - 95.4 x 104.9 mm {3.76 x 4.13 in} |
||
| Total displacement |
2.999 L {183 in3} |
||
| Compression ratio |
16.3 |
||
| Compression pressure |
3 MPa { 30.6 kgf/cm2 / 435 psi } /200 rpm |
||
| Idling revolution speed |
675 to 725 rpm |
||
| Valve clearance (between cam and roller) |
Inlet |
0.15 mm { 0.0059 in } , when cold |
|
| Exhaust |
0.15 mm { 0.0059 in } , when cold |
||
| Ignition method |
Compression ignition |
||
| Injection order |
1, 3, 4, 2 |
||
| Lubrication device |
Lubricating method |
Force feed type |
|
| Oil pump type |
Gear type |
||
| Lubricant capacity |
7.8 L { 2.06 US gal / 1.72 Imp.gal } |
||
| Oil amount when replacing |
2WD |
6.4 L { 1.69 US gal / 1.41 Imp.gal } With the oil filter not replaced |
|
| 7.0 L { 1.85 US gal / 1.54 Imp.gal } With the oil filter replaced |
|||
| 4WD |
6.9 L { 1.82 US gal / 1.52 Imp.gal } With the oil filter not replaced |
||
| 7.5 L { 1.98 US gal / 1.65 Imp.gal } With the oil filter replaced |
|||
| Oil filter type |
Full-flow filter, cartridge type |
||
| Oil cooler type |
Built-in type, water cooled |
||
| Cooling device |
Cooling method |
Water cooling force circulation method |
|
| Radiator type |
Corrugated fin type, force feed type |
||
| Water pump type |
Centrifugal impeller type, belt type |
||
| Thermostat type |
Wax type unit |
||
| Engine coolant capacity (Engine only) |
4.0 L { 1.06 US gal / 0.88 Imp.gal } |
||
| Engine coolant capacity (Radiator included) |
MT |
10.7 L { 2.83 US gal / 2.35 Imp.gal } With heater |
|
| 10.1 L { 2.67 US gal / 2.22 Imp.gal } Without heater |
|||
| AT |
11.1 L { 2.93 US gal / 2.44 Imp.gal } With heater |
||
| 10.5 L { 2.77 US gal / 2.31 Imp.gal } Without heater |
|||
| Fuel device |
Injection pump type |
Fuel supply pump, common rail (fuel rail) type |
|
| Injection nozzle type |
Electronically controlled injector, 8 holes |
||
| Charging device |
Generator |
Alternating current type |
|
| Output |
12 V - 90 A |
||
| Regulator |
IC type |
||
| Starter device |
Starting method |
Engage magnet type |
|
| Starter type |
Reduction type |
||
| Output |
12 V - 1.8 kW |
||
| Preheat device model |
Type |
Glow plug |
|
| Standard voltage - current |
12 V - 3.5 A |
||
| Item |
Specifications |
||
| Radiator |
Heat dissipation capacity |
126.6 kW {108856 kcal/h} |
|
| Front surface area |
0.355 m2 {3.8 ft2} |
||
| Dry mass |
6.6 kg { 14.6 lb } |
||
| Radiator cap |
Valve opening pressure |
93.3 to 122.7 kPa { 0.95 to 1.25 kgf/cm2 / 14 to 18 psi } |
|
| Water pump |
Pulley ratio |
1.250 |
|
| Delivery amount Pump rotation speed of 5600 rpm Engine coolant temperature of 30°C {86°F} |
240 L { 63.4 US gal / 52.8 Imp.gal } / rpm |
||
| Pump bearing type |
Double row axle |
||
| Thermostat |
Valve opening temperature |
85 ℃ { 185 °F } |
|
| Full open temperature |
100 ℃ { 212 °F } |
||
| Valve lift amount |
10 mm { 0.39 in } |
||
| Item |
Specifications |
| Oil pump relief valve operating pressure |
500 to 700 kPa { 5.1 to 7.1 kgf/cm2 / 73 to 102 psi } |
| Oil cooler relief valve operating pressure |
180 to 220 kPa { 1.8 to 2.2 kgf/cm2 / 26 to 32 psi } |
| Oil filter relief valve operating pressure |
80 to 120 kPa { 0.8 to 1.2 kgf/cm2 / 12 to 17 psi } |
| Oil pressure switch operating pressure |
29.4 to 49.0 kPa { 0.3 to 0.5 kgf/cm2 / 4 to 7 psi } |
| Regulating valve |
176 to 216 kPa { 1.8 to 2.2 kgf/cm2 / 26 to 31 psi } |
| Item |
Specifications |
| Silencer and tail pipe |
Circular section-shell construction of double skin and end plates, internal construction of baffles and perforated tubes |
| Suspension point |
Rubber |
| Suspension point number |
5 |
| Item |
Specifications |
|
| Specifications |
ACG90A |
|
| Rated voltage |
12 V |
|
| Rated output |
90 A |
|
| Rotational direction (When seen from the pulley side) |
Right |
|
| Maximum speed |
18,000 rpm |
|
| Item |
Specifications |
|
| Rating |
Voltage |
12 V |
| Output |
1.8 kW |
|
| Time |
30 seconds |
|
| Number of pinion teeth |
11 |
|
| Rotational direction |
Clockwise |
|
| Mass |
3.8 kg { 8.38 lb } |
|
| No-load characteristics |
Voltage/Current |
11.5 V/150 A |
| Rotational speed |
2,560 rpm |
|
| Load characteristic |
Voltage/Current |
8.1 V/430 A |
| Torque |
14.9 N・m { 1.5 kgf・m / 11 lb・ft } |
|
| Rotational speed |
890 rpm |
|
| Locking characteristic |
Voltage/Current |
2.5 V/675 A |
| Torque |
17.5 N・m { 1.8 kgf・m / 13 lb・ft } |
|