1. Component views
Rear seat belt (Crew cab)
Part name
- Rear pillar trim
- Rear end upper trim cover
- Rear end trim cover
- Rear pillar trim
- Rear tongue side seat belt (LH)
- Bolt
- Bolt
- Rear tongue side seat belt (CTR)
- Rear tongue side seat belt (RH)
- Rear buckle side seat belt
- Rear sill plate
Tightening torque
6: 46 N・m { 4.7 kgf・m / 34 lb・ft }
7: 8.2 N・m { 0.8 kgf・m / 73 lb・in }
2. Rear tongue side seat belt installation
1) Install the rear tongue side seat belt to the vehicle.
Tightening torque: 8.2 N・m { 0.8 kgf・m / 73 lb・in } M6 bolt
Tightening torque: 46 N・m { 4.7 kgf・m / 34 lb・ft } Except M6 bolt
Legend
- Rear tongue side seat belt (RH)
- Rear tongue side seat belt (CTR)
- Rear tongue side seat belt (LH)
2) Connect the connector to the pretensioner.
3) Return the seat back to the upright position.
4) Pass the rear tongue side seat belt through the seat belt guide, connect the seat belt guide to the rear seat headrest.
Legend
- Seat belt guide
3. Rear tongue side seat belt (center) connect
1) Pull out the rear tongue side seat belt (center) so that latch plate B faces the center of the vehicle.
Note
- Pull out the rear tongue side seat belt (center) without twisting.
Legend
- Latch plate B
- Rear tongue side seat belt (CTR)
2) Insert latch plate A into buckle A until a clicking sound can be heard.
Legend
- Buckle A
- Latch plate A
3) Pull the rear tongue side seat belt (center) in the direction of the arrow, and check that latch plate A and buckle A are securely fixed.
Legend
- Rear tongue side seat belt (CTR)
- Buckle A
- Latch plate A
4. Rear pillar trim cover installation
1) Install the rear pillar lower trim cover to the rear pillar.
Legend
- Claw section
- Rear pillar lower trim cover
- Clip
5. Rear end upper trim cover installation
1) Install the rear end upper trim cover to the body panel.
Caution
- For models with center top tethers (bracket type), install while bending the end of the rear end upper trim to an extent that it will not get damaged.
Models with center top tethers (bracket type)
Legend
- Seat belt guide cover
- Rear end upper trim cover
- Clip
- Claw section
- Hook
- Bend the end of the rear end upper trim cover.
- Install the rear end upper trim.
- Center top tether (Bracket type)
Models without center top tethers (bracket type)
Legend
- Seat belt guide cover
- Rear end upper trim cover
- Clip
- Claw section
- Hook
6. Rear door finisher installation
1) Install the rear door finisher to the body.
7. Rear sill plate installation
1) Install the rear sill plate to the floor.
Legend
- Rear sill plate
- Clip
- Claw section
8. SRS airbag setting
1. SRS reactivation
Warning
- Never use SRS parts from other vehicles or models.
- Make sure to check the part numbers and use the SRS components intended for the target vehicle.
1) Set the ignition switch to LOCK and remove the key.
Note
- For models with the passive entry and start system, turn the power mode OFF.
2) Make sure that the connectors of the SRS components (SRS airbag, SRS control unit, seat belt with pretensioner, SRS coil, etc.) are fully connected.
3) Install the SRS fuse to the fuse relay box, and connect the battery cable to the negative terminal of the battery.
4) Turn ON the ignition switch and verify that the SRS airbag warning light turns OFF after illuminating for 6 seconds.
Caution
- If the SRS airbag warning light does not operate properly, perform Diagnostic system check - SRS controls.
5) Referring to the following, perform the setting of the front door power window switch with AUTO UP/AUTO DOWN function.
Refer to "9.Body, Cab, Accessories 9T.Glass, Windows, Mirrors front door power window switch setting".