1. Sun sensor installation
1) Install the sun sensor to the instrument panel (upper side).
2) Connect the connector to the sun sensor.
Legend
- Sun sensor
- Instrument panel (Upper side)
2. Instrument panel installation
1) Install the instrument panel (upper side) to the instrument panel (lower side).
Tightening torque: 2.5 N・m { 0.25 kgf・m / 22.1 lb・in }
High grade type
Legend
- Instrument panel (Upper side)
- Clip
- Claw section
Low grade type
Legend
- Instrument panel (Upper side)
- Clip
- Claw section
2) Connect the connector to the instrument panel (upper side).
3) Connect the passenger airbag to the reinforcement.
Tightening torque: 25 N・m { 2.5 kgf・m / 18 lb・ft }
4) Install the side cover to the instrument panel.
Legend
- Side cover
- Claw section
3. Meter cluster installation
1) Install the meter cluster to the instrument panel.
RHD
Legend
- Clip
- Claw section
LHD
Legend
- Clip
- Claw section
4. Instrument panel passenger-side upper cover installation
1) Install the instrument panel passenger-side upper cover to the instrument panel.
Tightening torque: 2.5 N・m { 0.25 kgf・m / 22.1 lb・in } High grade type
High grade type (RHD)
Legend
- Instrument panel passenger-side upper cover
- Screw
High grade type (LHD)
Legend
- Instrument panel passenger-side upper cover
- Screw
Low grade type (RHD)
Legend
- Instrument panel passenger-side upper cover
Low grade type (LHD)
Legend
- Instrument panel passenger-side upper cover
5. Audio and navigation system installation
1. Models equipped with display units
1) Connect the connector to the display unit.
2) Install the display unit as a set with the bezel to the instrument panel.
Legend
- Bezel
- Display unit
- Clip
6. Front pillar trim cover installation
1. Models with assist grips
1) Install the front pillar trim cover to the front pillar.
2) Install the assist grip to the front pillar trim cover.
Tightening torque: 3.8 N・m { 0.4 kgf・m / 34 lb・in }
Legend
- Front pillar trim cover
- Assist grip
2. Models without assist grips
1) Install the assist grip to the front pillar trim cover.
Legend
- Front pillar trim cover
- Clip
7. Front door finisher installation
1) Install the front door finisher to the body.
8. Front sill plate installation
1) Install the front sill plate to the floor.
Regular cab, crew cab
Legend
- Front sill plate
- Clip
- Claw section
Extend cab
Legend
- Front sill plate
- Clip
- Claw section
9. SRS airbag setting
1. SRS reactivation
Warning
- Never use SRS parts from other vehicles or models.
- Make sure to check the part numbers and use the SRS components intended for the target vehicle.
1) Set the ignition switch to LOCK and remove the key.
Note
- For models with the passive entry and start system, turn the power mode OFF.
2) Make sure that the connectors of the SRS components (SRS airbag, SRS control unit, seat belt with pretensioner, SRS coil, etc.) are fully connected.
3) Install the SRS fuse to the fuse relay box, and connect the battery cable to the negative terminal of the battery.
4) Turn ON the ignition switch and verify that the SRS airbag warning light turns OFF after illuminating for 6 seconds.
Caution
- If the SRS airbag warning light does not operate properly, perform Diagnostic system check - SRS controls.
5) Referring to the following, perform the setting of the front door power window switch with AUTO UP/AUTO DOWN function.
Refer to "9.Body, Cab, Accessories 9T.Glass, Windows, Mirrors front door power window switch setting".