Head lining (extended cab) removal

1. Component views

Extend cab

Part name

  1. Sun visor
  2. Sun visor cover
  3. Sun visor holder
  4. Map light
  5. Dome light
  6. Assist grip
  7. Front pillar trim cover
  8. Assist grip
  9. Striker cover
  10. Rear pillar upper trim cover
  11. Rear pillar lower trim cover
  12. Rear end trim cover
  13. Front sill plate

2. Preliminary and post procedures

1. Preliminary procedures

1) Open the engine hood.

2) Disconnect the battery cable from the battery negative terminal.

Caution

  • After turning OFF the ignition switch (power mode for models with passive entry and start system), do not disconnect the battery cable within 3 minutes.
  • If the battery cable is disconnected within 3 minutes, the vehicle electronic control system may malfunction.
  • If the battery cable is disconnected, perform the setting of the front door power window switch with AUTO UP/AUTO DOWN function after connecting the battery negative terminal.

3. Assist grip removal

1. Models with assist grips

1) Remove the assist grip from the head lining.

Legend

  1. Assist grip
  2. Screw

4. Hole cover removal

1. Models without assist grips

1) Remove the hole cover from the head lining.

Legend

  1. Hole cover

5. Front sill plate removal

1) Remove the front sill plate from the floor.

Extend cab

Legend

  1. Front sill plate
  2. Clip
  3. Claw section

6. Front door finisher removal

1) Remove the front door finisher from the body.

7. Front pillar trim cover removal

1. Models with assist grips

1) Remove the assist grip from the front pillar trim cover.

2) Remove the front pillar trim cover from the front pillar.

Legend

  1. Front pillar trim cover
  2. Assist grip

2. Models without assist grips

1) Remove the front pillar trim cover from the front pillar.

Legend

  1. Front pillar trim cover
  2. Clip

8. Rear end trim cover removal

1) Remove the rear end trim cover from the body panel.

Extend cab

Legend

  1. Rear end trim cover
  2. Clip
  3. Hook
  4. Claw section

9. Rear pillar trim cover removal

1) Remove the seat belt lower anchor bolt from the floor panel.

Legend

  1. Seat belt lower anchor bolt

2) Remove the rear pillar lower trim cover from the rear pillar.

Legend

  1. Claw section
  2. Rear pillar lower trim cover
  3. Clip

3) Remove the seat belt upper anchor bolt from the rear pillar.

Legend

  1. Seat belt upper anchor bolt

4) Remove the rear upper trim cover from the rear pillar.

Legend

  1. Rear pillar upper trim cover
  2. Clip
  3. Hook

10. Striker cover removal

1) Remove the striker cover from the head lining.

Legend

  1. Striker cover
  2. Screw

11. Dome light removal

1) Remove the dome light from the head lining.

Legend

  1. Screw
  2. Dome light

2) Disconnect the connector from the dome light.

12. Map light removal

1) Insert a small flathead screwdriver, etc., into the gap between the head lining and the map light to unlock the claw section.

2) Remove the map light from the head lining.

Caution

  • Do not remove the map light with the claw section locked.

Legend

  1. Claw section
  2. Map light

3) Disconnect the connector from the map light.

13. Sun visor removal

1) Remove the sun visor cover from the sun visor bracket.

Legend

  1. Claw section
  2. Sun visor cover

2) Remove the sun visor from the head lining.

Legend

  1. Screw
  2. Sun visor

3) For models with mirror lights, disconnect the connector from the sun visor.

14. Head lining removal

1) Remove the clips from the head lining.

Legend

  1. Head lining
  2. Clip

2) Remove the sun visor holder from the head lining.

Note

  • Pull out the claw section while pressing it in the direction of the arrow.

Legend

  1. Sun visor holder
  2. Claw section

3) Remove the head lining from vehicle.

4) Disconnect the connector from the head lining.

Copyright Mazda Motor Corporation. All rights reserved.