RVM WARNING INDICATOR LIGHT DOES NOT ILLUMINATE UNDER ILLUMINATION CONDITIONS [REAR VEHICLE MONITORING SYSTEM]

id0903z7014300

Note

•  If there is any vehicle malfunction complaint lodged by a customer, perform FOREWORD [REAR VEHICLE MONITORING SYSTEM] malfunction diagnosis according to the troubleshooting procedure.

Rear Vehicle Monitoring Control Module Connector 10-pin Type

Description

•  The RVM warning indicator light flashes/does not illuminate while under the illumination conditions (Vehicle speed above 30 km/h {19 mph}, turn-signals off, and vehicle in detection area).

Possible malfunction

Note

•  The detection performance of the rear vehicle monitoring control module has limitations and the Rear vehicle monitoring system may not operate normally. For the detection performance limitations, refer to the [REAR VEHICLE MONITORING CONTROL MODULE] in the technical guide.

•  Rear vehicle monitoring control modules false-detect that a vehicle is outside detection area when it is actually inside of it, or cannot determine that no vehicle is entering blind-spot area.

―  Rear vehicle monitoring control module radar is not emitted inside detection area (deviates from blind-spot area or adjacent lanes)

•  Damage, deformity or looseness to installation bracket or vehicle frame (including moderate impacts)

•  Incorrect installation of rear bumper, soiling to radar emitting/receiving area, application of stickers (including transparent types), repairs using putty application

―  Rear vehicle monitoring control module radar does not receive echo-back correctly

•  Rear vehicle monitoring control module malfunction

•  Incorrect installation of rear bumper, soiling to radar emitting/receiving area, application of stickers (including transparent types), repairs using putty application

―  Effect of non-genuine, after-market electronic device installation

Note

•  The radar sensor cannot receive echo-back correctly if there is a thick moisture film (such as condensation) or excessive soiling covering the rear bumper radar emitting/receiving areas.

•  Non-genuine rear bumper or paint, or installation of after-market parts may negatively affect radar echo-back ability.

•  RVM warning indicator light illumination disabled

―  RVM warning indicator light malfunction

―  Rear vehicle monitoring control module (LH) malfunction (RVM warning indicator light illumination circuit malfunction)

Diagnostic procedure

Warning

•  When performing a road test, always verify the safety of the surrounding area before performing the test.

•  Do not perform a road test at a speed which exceeds the legal speed limit.

•  To assure safety, perform a road test using two people when the vehicle is being driven. (One drives the vehicle and the other operates the M-MDS.)

Step	Inspection		Action
1	DETERMINE IF MALFUNCTION CAUSE IS RVM WARNING LIGHT (ORANGE) OR RVM WARNING INDICATOR LIGHT ILLUMINATION CIRCUIT •  Turn the following rear vehicle monitoring system simulation items on and off using the M-MDS. (See ACTIVE COMMAND MODES INSPECTION [REAR VEHICLE MONITORING SYSTEM].) ―  WRN_IND_R ―  WRN_IND_L •  Does the RVM warning indicator light illuminate/turn off?	Yes	Go to Step 3.
		No	Go to the next step.
2	DETERMINE IF MALFUNCTION CAUSE IS REAR VEHICLE MONITORING CONTROL MODULES OR RVM WARNING INDICATOR LIGHTS •  Inspect the following: RVM warning indicator light (RH) related: ―  RVM warning indicator light (RH) ―  Wiring harness between RVM warning indicator light (RH) terminal G and rear vehicle monitoring control module (LH) terminal I ―  Wiring harness between RVM warning indicator light (RH) terminal H and rear vehicle monitoring control module (LH) terminal H RVM warning indicator light (LH) related: ―  RVM warning indicator light (LH) ―  Wiring harness between RVM warning indicator light (LH) terminal G and rear vehicle monitoring control module (LH) terminal B ―  Wiring harness between RVM warning indicator light (LH) terminal H and rear vehicle monitoring control module (LH) terminal F •  Is any malfunction verified?	Yes	Repair or replace the malfunctioning location.
		No	Replace the rear vehicle monitoring control module (LH). (See REAR VEHICLE MONITORING CONTROL MODULE REMOVAL/INSTALLATION.)
3	VERIFY REAR BUMPER CONDITION •  Inspect the rear bumper at the rear vehicle monitoring control modules installation areas for the following: ―  Installation condition ―  Application of stickers (including transparent types) ―  Excessive soiling ―  Repairs using putty •  Is the rear bumper condition normal?	Yes	Go to the next step.
		No	Repair or replace the malfunctioning part, or replace the rear bumper. (See REAR BUMPER REMOVAL/INSTALLATION.)
4	VERIFY INSTALLATION CONDITION OF REAR VEHICLE MONITORING CONTROL MODULES •  Remove the rear bumper. (See REAR BUMPER REMOVAL/INSTALLATION.) •  Inspect the installation condition of the rear vehicle monitoring control modules for the following: ―  Looseness ―  Damage or deformity to the bracket ―  Distortion at vehicle installation surface •  Is the rear vehicle monitoring control modules installation condition normal?	Yes	Go to the next step.
		No	Repair or replace the malfunctioning location.
5	VERIFY IF MALFUNCTION CAUSE IS AFTER-MARKET ELECTRONIC DEVICE INSTALLATION •  Verify if malfunction symptom recurs as stated by customer. •  Does the malfunction recur?	Yes	Go to the next step.
		No	Explain to the customer that the malfunction occurred due to the after-market electronic device installation.
6	INSPECT REAR VEHICLE MONITORING CONTROL MODULES •  Inspect the malfunctioning rear vehicle monitoring control module. •  Is the rear vehicle monitoring control module normal?	Yes	Temporary malfunction with the radar echo-back. If the same symptom recurs repeatedly, replace the rear vehicle monitoring control module. (See REAR VEHICLE MONITORING CONTROL MODULE REMOVAL/INSTALLATION.)
		No	Replace the applicable rear vehicle monitoring control module. (See REAR VEHICLE MONITORING CONTROL MODULE REMOVAL/INSTALLATION.)

Rear Vehicle Monitoring Control Module Connector 12-pin Type

Description

•  The RVM warning indicator light flashes/does not illuminate while under the illumination conditions (Vehicle speed above 30 km/h {19 mph}, turn-signals off, and vehicle in detection area).

Possible malfunction

•  Rear vehicle monitoring control modules false-detect that a vehicle is outside detection area when it is actually inside of it, or cannot determine that no vehicle is entering blind-spot area.

―  Rear vehicle monitoring control module radar is not emitted inside detection area (deviates from blind-spot area or adjacent lanes)

•  Damage, deformity or looseness to installation bracket or vehicle frame (including moderate impacts)

•  Incorrect installation of rear bumper, soiling to radar emitting/receiving area, application of stickers (including transparent types), repairs using putty application

―  Rear vehicle monitoring control module radar does not receive echo-back correctly

•  Rear vehicle monitoring control module malfunction

•  Incorrect installation of rear bumper, soiling to radar emitting/receiving area, application of stickers (including transparent types), repairs using putty application

―  Effect of non-genuine, after-market electronic device installation

Note

•  The radar sensor cannot receive echo-back correctly if there is a thick moisture film (such as condensation) or excessive soiling covering the rear bumper radar emitting/receiving areas.

•  Non-genuine rear bumper or paint, or installation of after-market parts may negatively affect radar echo-back ability.

•  RVM warning indicator light illumination disabled

―  RVM warning indicator light malfunction

―  Rear vehicle monitoring control module (LH) malfunction (RVM warning indicator light illumination circuit malfunction)

Diagnostic procedure

Warning

•  When performing a road test, always verify the safety of the surrounding area before performing the test.

•  Do not perform a road test at a speed which exceeds the legal speed limit.

•  To assure safety, perform a road test using two people when the vehicle is being driven. (One drives the vehicle and the other operates the M-MDS.)

Step	Inspection		Action
1	DETERMINE IF MALFUNCTION CAUSE IS RVM WARNING LIGHT (ORANGE) OR RVM WARNING INDICATOR LIGHT ILLUMINATION CIRCUIT •  Turn the following rear vehicle monitoring system simulation items on and off using the M-MDS. (See ACTIVE COMMAND MODES INSPECTION [REAR VEHICLE MONITORING SYSTEM].) ―  WRN_IND_R ―  WRN_IND_L •  Does the RVM warning indicator light illuminate/turn off?	Yes	Go to Step 3.
		No	Go to the next step.
2	DETERMINE IF MALFUNCTION CAUSE IS REAR VEHICLE MONITORING CONTROL MODULES OR RVM WARNING INDICATOR LIGHTS •  Inspect the following: RVM warning indicator light (RH) related: ―  RVM warning indicator light (RH) ―  Wiring harness between RVM warning indicator light (RH) terminal G and rear vehicle monitoring control module (LH) terminal D ―  Wiring harness between RVM warning indicator light (RH) terminal H and rear vehicle monitoring control module (LH) terminal C RVM warning indicator light (LH) related: ―  RVM warning indicator light (LH) ―  Wiring harness between RVM warning indicator light (LH) terminal G and rear vehicle monitoring control module (LH) terminal K ―  Wiring harness between RVM warning indicator light (LH) terminal H and rear vehicle monitoring control module (LH) terminal G •  Is any malfunction verified?	Yes	Repair or replace the malfunctioning location.
		No	Replace the rear vehicle monitoring control module (LH). (See REAR VEHICLE MONITORING CONTROL MODULE REMOVAL/INSTALLATION.)
3	VERIFY REAR BUMPER CONDITION •  Inspect the rear bumper at the rear vehicle monitoring control modules installation areas for the following: ―  Installation condition ―  Application of stickers (including transparent types) ―  Excessive soiling ―  Repairs using putty •  Is the rear bumper condition normal?	Yes	Go to the next step.
		No	Repair or replace the malfunctioning part, or replace the rear bumper. (See REAR BUMPER REMOVAL/INSTALLATION.)
4	VERIFY INSTALLATION CONDITION OF REAR VEHICLE MONITORING CONTROL MODULES •  Remove the rear bumper. (See REAR BUMPER REMOVAL/INSTALLATION.) •  Inspect the installation condition of the rear vehicle monitoring control modules for the following: ―  Looseness ―  Damage or deformity to the bracket ―  Distortion at vehicle installation surface •  Is the rear vehicle monitoring control modules installation condition normal?	Yes	Go to the next step.
		No	Repair or replace the malfunctioning location.
5	VERIFY IF MALFUNCTION CAUSE IS AFTER-MARKET ELECTRONIC DEVICE INSTALLATION •  Verify if malfunction symptom recurs as stated by customer. •  Does the malfunction recur?	Yes	Go to the next step.
		No	Explain to the customer that the malfunction occurred due to the after-market electronic device installation.
6	INSPECT REAR VEHICLE MONITORING CONTROL MODULES •  Inspect the malfunctioning rear vehicle monitoring control module. •  Is the rear vehicle monitoring control module normal?	Yes	Temporary malfunction with the radar echo-back. If the same symptom recurs repeatedly, replace the rear vehicle monitoring control module. (See REAR VEHICLE MONITORING CONTROL MODULE REMOVAL/INSTALLATION.)
		No	Replace the applicable rear vehicle monitoring control module. (See REAR VEHICLE MONITORING CONTROL MODULE REMOVAL/INSTALLATION.)