DTC P2226:00 [PCM (SKYACTIV-D 2.2)]

id0102j5159300

Note

• To determine the malfunctioning part, proceed with the diagnostics from [Function inspection using M-MDS].

Details on DTCs

System malfunction location

BARO sensor in PCM: Run error

Detection condition

Determination condition

•  Malfunction in BARO sensor signal circuit in PCM occurs.

Preconditions

•  All of the following conditions are met.

―  Battery voltage: 8—16 V

―  0.5 s elapses after engine is started

Drive cycle

•  1

Self-test type

•  CMDTC self test

Sensor/unit used

•  BARO sensor (integrated with PCM)

Fail-safe

•  Inhibits the automatic diesel particulate filter regeneration control.

•  Inhibits the manual diesel particulate filter regeneration control.

•  Inhibits the EGR control.

•  Stops the G-vectoring control (GVC).

•  Limits the engine transaxle total control.

•  Inhibits engine-stop by i-stop control.

Vehicle status when DTCs are output

•  Check engine light turns on

Possible Cause

•  BARO sensor malfunction (integrated with PCM)

•  PCM malfunction

System malfunction location	BARO sensor in PCM: Run error
Detection condition	Determination condition	• Malfunction in BARO sensor signal circuit in PCM occurs.
Preconditions	• All of the following conditions are met. ― Battery voltage: 8—16 V ― 0.5 s elapses after engine is started
Drive cycle	• 1
Self-test type	• CMDTC self test
Sensor/unit used	• BARO sensor (integrated with PCM)
Fail-safe	• Inhibits the automatic diesel particulate filter regeneration control. • Inhibits the manual diesel particulate filter regeneration control. • Inhibits the EGR control. • Stops the G-vectoring control (GVC). • Limits the engine transaxle total control. • Inhibits engine-stop by i-stop control.
Vehicle status when DTCs are output	• Check engine light turns on
Possible Cause	• BARO sensor malfunction (integrated with PCM) • PCM malfunction

System Wiring Diagram

• Not applicable

Function Explanation (DTC Detection Outline)

• If there is communication error between the BARO sensor control driver and the CPU, the PCM stores a DTC.

Repeatability Verification Procedure

• Leave the vehicle for 10 s with the ignition switched ON (engine off) or while idling.

PID Item/Simulation Item Used in Diagnosis

• Not applicable

Function Inspection Using M-MDS

Step

Inspection

Results

Action

1

PURPOSE: RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION

Note

• Recording can be facilitated using the screen capture function of the PC.

• Record the freeze frame data/snap shot data.

―

Go to the troubleshooting procedure to perform the procedure from Step 1.

Step	Inspection	Results	Action
1	PURPOSE: RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture function of the PC. • Record the freeze frame data/snap shot data.	―	Go to the troubleshooting procedure to perform the procedure from Step 1.

Troubleshooting Diagnostic Procedure

Intention of troubleshooting procedure

• Step 1

― Perform a unit inspection of the BARO sensor.

• Steps 2 to 3

― Verify that the primary malfunction is resolved and there are no other malfunctions.

Step

Inspection

Results

Action

1

PURPOSE: INSPECT BARO PRESSURE SENSOR

•  Inspect the BARO sensor.
(See BAROMETRIC PRESSURE (BARO) SENSOR INSPECTION [SKYACTIV-D 2.2].)

•  Is the BARO sensor normal?

Yes

Go to the next step.

No

Replace the BARO sensor., then go to the next step.

(See BAROMETRIC PRESSURE (BARO) SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

2

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Reconnect all the disconnected connectors.

•  Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC.
(See CLEARING DTC [PCM (SKYACTIV-D 2.2)].)

•  Implement the repeatability verification procedure.
(See Repeatability Verification Procedure.)

•  Display the DTCs using the M-MDS.
(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].)

•  Has DTC P2226:00 been recorded?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

No

Go to the next step.

3

VERIFY OTHER DTCs

•  Has any other DTC or pending code been stored?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-D 2.2)].)

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	PURPOSE: INSPECT BARO PRESSURE SENSOR • Inspect the BARO sensor. (See BAROMETRIC PRESSURE (BARO) SENSOR INSPECTION [SKYACTIV-D 2.2].) • Is the BARO sensor normal?	Yes	Go to the next step.
1		No	Replace the BARO sensor., then go to the next step. (See BAROMETRIC PRESSURE (BARO) SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
2	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Reconnect all the disconnected connectors. • Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC. (See CLEARING DTC [PCM (SKYACTIV-D 2.2)].) • Implement the repeatability verification procedure. (See Repeatability Verification Procedure.) • Display the DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].) • Has DTC P2226:00 been recorded?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
2		No	Go to the next step.
3	VERIFY OTHER DTCs • Has any other DTC or pending code been stored?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-D 2.2)].)
3		No	DTC troubleshooting completed.