DTC P117A:00 [PCM (WITHOUT CYLINDER DEACTIVATION (SKYACTIV-G 2.0, SKYACTIV-G 2.5))]

id0102sc316900

DTC P117A:00

Engine oil temperature is high
DETECTION CONDITION
•  Any one of the following conditions is met:
―  With the transmission in 5th gear or lower gear, an engine speed of 6,100 rpm (SKYACTIV-G 2.0)/5,800 rpm (SKYACTIV-G 2.5) or more continues for 6 min.
―  The estimated engine oil temperature exceeds 140 °C {284 °F} continues for 6 min (with active air shutter).
Diagnostic support note
•  This is a continuous monitor (other).
•  The check engine light does not illuminate.
•  FREEZE FRAME DATA is not available.
•  Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
•  Restricts the upper limit of the engine speed.
POSSIBLE CAUSE
•  High engine speed condition continues
•  Active air shutter close malfunction (with active air shutter)
•  PCM malfunction
SYSTEM WIRING DIAGRAM
•  Not applicable

Diagnostic Procedure

STEP

INSPECTION

RESULTS

ACTION
1
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
Note
•  Recording can be facilitated using the screen capture function of the PC.
•  Record the snapshot data on the repair order.
—
Go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY RELATED PENDING CODE AND/OR DTC
•  Switch the ignition off, then ON (engine off).
•  Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
•  Is the PENDING CODE/DTC P0335:00, P059F:00, P05A0:00, P05A3:00, P05C0:00 or U0284:00 also present?
Yes
Go to the applicable PENDING CODE or DTC inspection.
(See DTC P0335:00 [PCM (WITHOUT CYLINDER DEACTIVATION (SKYACTIV-G 2.0, SKYACTIV-G 2.5))].)
(See DTC P059F:00 [PCM (WITHOUT CYLINDER DEACTIVATION (SKYACTIV-G 2.0, SKYACTIV-G 2.5))].)
(See DTC P05A0:00 [PCM (WITHOUT CYLINDER DEACTIVATION (SKYACTIV-G 2.0, SKYACTIV-G 2.5))].)
(See DTC P05A3:00 [PCM (WITHOUT CYLINDER DEACTIVATION (SKYACTIV-G 2.0, SKYACTIV-G 2.5))].)
(See DTC P05C0:00 [PCM (WITHOUT CYLINDER DEACTIVATION (SKYACTIV-G 2.0, SKYACTIV-G 2.5))].)
(See DTC U0284:00 [PCM (WITHOUT CYLINDER DEACTIVATION (SKYACTIV-G 2.0, SKYACTIV-G 2.5))].)
No
Go to the next step.
4
INSPECT VEHICLE CONDITION FOR EFFECT ON MALFUNCTION
•  Verify how the customer drives the vehicle by asking the customer the following:
•  Does the engine speed exceed 6,100 rpm (SKYACTIV-G 2.0)/5,800 rpm (SKYACTIV-G 2.5) for 6 min or more while driving in 5th gear or lower gear?
Yes
Explain to the customer that the vehicle is normal. (performs control to protect the engine due to continuous engine speed exceeding 6,100 rpm (SKYACTIV-G 2.0)/5,800 rpm (SKYACTIV-G 2.5) for 6 min or more while in 5th gear or lower gear)
If there is a concern with customer’s driving, provide the customer some pertinent advice (such as gear selection, how to use manual mode).
Go to the next step.
No
Go to the next step.
5
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Always reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Start the engine and warm it up completely.
•  Drive the vehicle.
•  Perform the DTC Reading Procedure.
•  Is the same DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM.
Go to the next step.
No
Go to the next step.
6
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [PCM (WITHOUT CYLINDER DEACTIVATION (SKYACTIV-G 2.0, SKYACTIV-G 2.5))].)
No
DTC troubleshooting completed.