DTC B00A0:54 [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)]

id0802g8835700

System malfunction location

•  Occupant classification sensor calibration setting not set

Detection condition

Warning

•  Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.

•  Occupant classification sensor calibration setting has not been done correctly

Fail-safe

Not applicable

Possible cause

•  Occupant classification sensor calibration setting not implemented

•  Occupant classification sensor calibration setting invalid

•  Occupant classification sensor control module malfunction

System wiring diagram

Not applicable

System malfunction location	• Occupant classification sensor calibration setting not set
Detection condition	Warning • Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure. • Occupant classification sensor calibration setting has not been done correctly
Fail-safe	Not applicable
Possible cause	• Occupant classification sensor calibration setting not implemented • Occupant classification sensor calibration setting invalid • Occupant classification sensor control module malfunction
System wiring diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Action

1

PERFORM OCCUPANT CLASSIFICATION SENSOR CALIBRATION

•  Perform the calibration for the occupant classification sensor using the M-MDS.
(See OCCUPANT CLASSIFICATION SENSOR CALIBRATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

•  Clear the DTC for the SAS control module using the M-MDS.
(See CLEARING DTC [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].)

•  Perform the DTC inspection for the SAS control module using the M-MDS.
(See DTC INSPECTION [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].)

•  Is the same DTC present?

Yes

Perform the occupant classification sensor calibration, then go to the next step.

(See OCCUPANT CLASSIFICATION SENSOR CALIBRATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)

No

Go to the next step.

2

PERFORM SAS CONTROL MODULE DTC INSPECTION

•  Clear the DTC for the SAS control module using the M-MDS.
(See CLEARING DTC [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].)

•  Perform the DTC inspection for the SAS control module using the M-MDS.
(See DTC INSPECTION [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].)

•  Is the same DTC present?

Yes

Replace the occupant classification sensor.

(See FRONT SEAT CUSHION TRIM REMOVAL/INSTALLATION.)

No

DTC troubleshooting completed.

Step	Inspection		Action
1	PERFORM OCCUPANT CLASSIFICATION SENSOR CALIBRATION • Perform the calibration for the occupant classification sensor using the M-MDS. (See OCCUPANT CLASSIFICATION SENSOR CALIBRATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) • Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].) • Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].) • Is the same DTC present?	Yes	Perform the occupant classification sensor calibration, then go to the next step. (See OCCUPANT CLASSIFICATION SENSOR CALIBRATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)
1		No	Go to the next step.
2	PERFORM SAS CONTROL MODULE DTC INSPECTION • Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].) • Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)].) • Is the same DTC present?	Yes	Replace the occupant classification sensor. (See FRONT SEAT CUSHION TRIM REMOVAL/INSTALLATION.)
2		No	DTC troubleshooting completed.