PID/DATA MONITOR TABLE [FRONT BODY CONTROL MODULE (FBCM)]
id0902p2012000
|
PID |
Unit/Operation |
Data contents |
Data read/use method |
Module control terminal |
|---|---|---|---|---|
|
ABK_CS_BG*1
|
Off/On
|
Theft-deterrent system answer-back signal input status
• Off: Theft-deterrent system answer-back signal is not received.
• On: Theft-deterrent system answer-back signal is received.
|
Theft-deterrent system answer-back request signal input from rear body control module (RBCM)
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
ABK_CS_KEY
|
Off/On
|
Keyless entry system answer-back signal input status
• Off: Keyless entry system answer-back signal is not received.
• On: Keyless entry system answer-back signal is received.
|
Answer-back request signal input for keyless entry system from rear body control module (RBCM)
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
ABK_HD_CS_R
|
Off/On
|
|
||
|
ABK_HN_CS_R
|
Off/On
|
|
||
|
ABK_HN_KEY
|
Off/On
|
Keyless entry system horn answer-back signal input status
• Off: Keyless entry system horn answer-back signal is not received.
• On: Keyless entry system horn answer-back signal is received.
|
Keyless entry system horn answer-back request signal input from rear body control module (RBCM)
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
BAT_TMP
|
°C, °F
|
Displays battery temperature (estimated).
|
Estimated battery temperature transmitted by LIN communication from current sensor
|
2E (LIN)
|
|
BG_ALARM_CS*1
|
Off/On
|
Theft-deterrent system alarm signal input status
• Off: Hazard warning light flashing request signal is not received
• On: Hazard warning light flashing request signal is received
|
Theft-deterrent system alarm request signal input from rear body control module (RBCM)
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
BLWR_MT_RY
|
Off/On
|
Blower motor relay output signal status
• Off: Blower relay is off.
• On: Blower relay is on.
|
—
|
2Z (Blower motor relay control)
|
|
BRAKE_SW
|
Off/On
|
Brake switch operation status
• Off: Brake switch (No. 2 signal) is off. (Brake pedal is depressed.)
• On: Brake switch (No. 2 signal) is on. (Brake pedal is not depressed.)
|
Brake switch signal status detected by PCM
|
• 2N (CAN_L)
• 2P (CAN_H)
|
|
BRK_F_L_SW
|
Normal/Low/Reserved/Unknown
|
Brake fluid level condition
• Normal: Brake fluid level is between MAX and MIN.
• Low: Brake fluid level is lower than MIN.
• Reserved: —
• Unknown: Brake fluid level is not determined.
|
—
|
2Q (Brake fluid level switch signal)
|
|
DCDC_CVT_ST
|
Wake_Up/Bypass/Boost_1/Boost_2/Boost_3/Error/Default
|
DC-DC converter status
|
—
|
2H (LIN)
|
|
DCDC_VLT_O
|
V
|
Displays DC-DC converter output voltage.
|
—
|
2H (LIN)
|
|
DEFOG_F_CS
|
Off/On
|
Front defogger operation request signal from heater control unit
• Off: Front window defogger control signal is not received.
• On: Front window defogger control signal is received.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
DEFOG_R_CS
|
Off/On
|
Rear defogger operation request signal from heater control unit
• Off: Rear window defogger control signal is not received.
• On: Rear window defogger control signal is received.
|
For manual A/C vehicles, request signal transmission is via LIN communication.
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
ENG_C_TMP
|
°C, °F
|
Displays the engine coolant temperature value from the PCM.
|
—
|
• 2N (CAN_L)
• 2P (CAN_H)
|
|
ESS_ST
|
Off/On
|
Emergency signal system (ESS) operation condition
• Off: Emergency signal system (ESS) is not operated.
• On: Emergency signal system (ESS) is operated.
|
—
|
—
|
|
F_FOG_LMP*2
|
Off/On
|
Front fog light control signal
• Off: Front fog light is turned off.
• On: Front fog light is turned on.
|
—
|
—
|
|
F_FOG_SW*2
|
Off/On
|
Front fog light switch input signal from start stop unit
• Off: Front fog light switch F.FOG signal is not received.
• On: Front fog light switch F.FOG signal is received.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
H/L
|
OFF/DRL/TNS/H/L_LOW/H/L_HI
|
Headlight control signal
• OFF: Headlight is turned off.
• DRL: DRL is turned on.
• TNS: TNS (parking lights) is turned on.
• H/L_LOW: Headlight (LO) is turned on.
• H/L_HI: Headlight (HI) is turned on.
|
—
|
—
|
|
H/L_CLN_RY
|
Off/On
|
Headlight cleaner relay control signal
• Off: Headlight cleaner relay is off.
• On: Headlight cleaner relay is on.
|
—
|
1Q (Headlight cleaner motor control)
|
|
H/L_CS_RLS*3
|
Off/TNS_On/TNS+H/L_On/TNS+H/L_On_J
|
Headlight control input signal from auto light sensor/rain sensor
• Off: TNS (parking lights) and headlight on request signal is not received from auto light sensor.
• TNS_On: TNS (parking lights) on signal is received from auto light sensor.
• TNS+H/L_On: TNS (parking lights) and headlight LO on signal is received from auto light sensor.
• TNS+H/L_On_J: —
|
—
|
2G (LIN)
|
|
H/L_HI
|
Off/On
|
Headlight HI beams
• Off: Headlight HI is turned off.
• On: Headlight HI is turned on.
|
—
|
—
|
|
H/L_SW_HI
|
Off/On
|
Light switch position (HI) condition via CAN signal from start stop unit
• Off: Light switch HI signal is not received.
• On: Light switch HI signal is received.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
H/L_SW_LOW1
|
Off/On
|
Displays dimmer switch position of light switch sent from start stop unit via CAN signal
• Off: Other than dimmer switch LO position of light switch is received
• On: Dimmer switch LO position of light switch is received
|
Verify if the monitor value switches when the dimmer switch of the light switch is switched between LO and HI positions. If the dimmer switch operation and monitor values do not match, inspect the start stop unit or CAN communication.
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
H/L_SW_OFF
|
Off/On
|
Light switch position (OFF) condition via CAN signal from start stop unit
• Off: Light switch OFF signal is not received.
• On: Light switch OFF signal is received.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
H/L_SW_PASS
|
Off/On
|
Light switch position (PASS) condition via CAN signal from start stop unit
• Off: Light switch FLASH-TO-PASS signal is not received.
• On: Light switch FLASH-TO-PASS signal is received.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
H/L_SW_TNS
|
Off/On
|
Light switch position (TNS (parking lights)) status via CAN signal from start stop unit
• Off: Light switch TNS (parking lights) signal is not received.
• On: Light switch TNS (parking lights) signal is received.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
H/L_TNS
|
Off/On
|
Light switch (TNS (parking lights)) output signal
• Off: TNS (parking lights) is turned off.
• On: TNS (parking lights) is turned on.
|
—
|
—
|
|
HAZARD_LMP
|
Off/On
|
Hazard light output signal
• Off: Hazard light is turned off.
• On: Hazard light is turned on.
|
—
|
—
|
|
HAZARD_SW
|
Off/On/Unknown
|
Hazard switch input signal from start stop unit
• Off: Hazard warning switch is not pressed.
• On: Hazard warning switch is pressed.
• Unknown: Hazard warning switch on/off is not determined.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
HBC_CS*4
|
Off/On/Invalid
|
High beam control (HBC) system control signal input from forward sensing camera (FSC)
• Off: High beam control (HBC) system signal is not received.
• On: High beam control (HBC) system signal is received.
• Invalid: High beam control (HBC) system signal has error.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
HBC_ST*4
|
Off/On
|
Operation status of high beam control (HBC) system
• Off: High beam control (HBC) system is not operated.
• On: High beam control (HBC) system is operated.
|
Control status of high beam control (HBC) system of front body control module (FBCM) by signal from forward sensing camera (FSC)
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
HEAT_CS_R
|
Off/On
|
|
||
|
IG_ST
|
Off/On
|
Ignition switch status
• Off: IG1 is off.
• On: IG1 is on.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
L_OFF_AUTO
|
Off/On
|
|
||
|
L_OFF_BS
|
Off/On
|
|
||
|
OIL_P_SW
|
Off(Normal)/On(Low)
|
|
||
|
OUT_CAR_TMP
|
°C, °F
|
Displays the ambient temperature value input from the PCM.
|
—
|
• 2N (CAN_L)
• 2P (CAN_H)
|
|
P_BRAKE_SW
|
Off/On
|
Electric parking brake switch status having input from instrument cluster
• Off: Electric parking brake switch is off.
• On: Electric parking brake switch is on.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
PNC_CS
|
Off/On
|
Panic signal input from rear body control module (RBCM)
• Off: Panic control signal is not received.
• On: Panic control signal is received.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
PNC_HD_CS_R
|
Off/On
|
|
||
|
PNC_HN_CS_R
|
Off/On
|
|
||
|
PTC_HEAT_CS*9
|
Off/On
|
PTC heater operation request signal from climate control unit
• Off: PTC heater control signal is not received.
• On: PTC heater control signal is received.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
R_FOG_LMP*8
|
Off/On
|
Rear fog light control signal
• Off: Rear fog light is turned off.
• On: Rear fog light is turned on.
|
—
|
—
|
|
R_FOG_SW*8
|
Off/On
|
Rear fog light switch input signal from start stop unit
• Off: Rear fog light switch is not in R.FOG position
• On: Rear fog light switch is in R.FOG position
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
RES_CS
|
Off/On
|
|
||
|
RLS_FLT*3
|
O.K./FAULT
|
Fail determination signal of auto light sensor/rain sensor
• O.K.: Rain sensor is normal.
• FAULT: Rain sensor has a malfunction.
|
If normal, the value is O.K.. If abnormal, FAULT.
|
2G (LIN)
|
|
S_HT_CUT*5
|
No_Request/Cut
|
The FBCM controls the seat warmer output at an appropriate timing in consideration of the vehicle conditions such as power supply voltage decrease.
• No_Request: Except below
• Cut: When FBCM stops or lowers seat warmer output
|
—
|
—
|
|
SHIFT_L_POS*6
|
Between/P/R/N/D/S(2)/L(1)
|
Selector lever position signal from TCM
• Between: Selector lever is between two positions.
• P: Selector lever is in P position.
• R: Selector lever is in R position.
• N: Selector lever is in N position.
• D: Selector lever is in D position.
• S(2): Selector lever is in D position 2nd gear.
• L(1): Selector lever is in D position 1st gear.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
TURN_L_L
|
Off/On
|
Turn light (LH) output signal
• Off: Turn light (LH) is turned off.
• On: Turn light (LH) is turned on.
|
—
|
—
|
|
TURN_L_R
|
Off/On
|
Turn light (RH) output signal
• Off: Turn light (RH) is turned off.
• On: Turn light (RH) is turned on.
|
—
|
—
|
|
TURN_SW
|
Off/Turn_R_On/Turn_L_On/Unknown
|
Turn switch signal input from start stop unit
• Off: Turn switch is in OFF position.
• Turn_R_On: Turn switch is in RH position.
• Turn_L_On: Turn switch is in LH position.
• Unknown: Turn switch position is not determined.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
VPWR_B
|
V
|
Displays front body control module (FBCM) power supply voltage
|
—
|
2A, 3K, 3L (Power supply)
|
|
VSPD
|
KPH, MPH
|
Displays the vehicle speed signal from the PCM.
|
—
|
• 2N (CAN_L)
• 2P (CAN_H)
|
|
WAS_FLUID_L*7
|
Normal/Low/Reserved/Unknown
|
Washer fluid level
• Normal: Washer fluid level is normal.
• Low: Washer fluid level is low.
• Reserved: —
• Unknown: Washer fluid level is not determined.
|
—
|
2S (Washer level switch signal)
|
|
WAS_MT_RY_F
|
Off/On
|
Windshield washer motor relay operation signal
• Off: Windshield washer motor relay is off.
• On: Windshield washer motor relay is on.
|
—
|
3F (Windshield washer motor control)
|
|
WAS_MT_RY_R
|
Off/On
|
Rear washer motor relay operation signal
• Off: Rear washer motor relay is off.
• On: Rear washer motor relay is on.
|
—
|
3H (Rear window washer motor control)
|
|
WASHER_F
|
Off/On
|
Windshield washer switch input signal from start stop unit
• Off: Windshield washer switch is off.
• On: Windshield washer switch is on.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
WASHER_R
|
Off/On
|
Rear washer switch input signal from start stop unit
• Off: Rear wiper and washer switch is not in rear washer position.
• On: Rear wiper and washer switch is in rear washer position.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
WIP_CS_RLS*3
|
Off/Single_Wipe/F_Wiper_LOW/F_Wiper_HI/Failure
|
Auto wiper input signal from auto light sensor/rain sensor
• Off: Wiper operation signal is not received from rain sensor.
• Single_Wipe: Signal to operate wiper once is received from rain sensor.
• F_Wiper_LOW: Signal to operate wiper at low speed is received from rain sensor.
• F_Wiper_HI: Signal to operate wiper at high speed is received from rain sensor.
• Failure: Communication with rain sensor is failed.
|
—
|
2G (LIN)
|
|
WIP_F
|
OFF/LOW/HI/INT / AUTO
|
Windshield wiper switch input signal from start stop unit
• OFF: Windshield wiper switch is in OFF position.
• LOW: Windshield wiper switch is in LO position.
• HI: Windshield wiper switch is in HI position.
• INT / AUTO: Windshield wiper switch is in INT or AUTO position.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
WIP_F_INT_L
|
%
|
Displays the windshield wiper intermittent interval time input signal from start stop unit.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
WIP_F_LOW*10
|
Off/On
|
Windshield wiper LO switch input status
• Off: Windshield wiper switch is not in LO position.
• On: Windshield wiper switch is in LO position.
|
—
|
2Y (Windshield wiper (LO) switch signal)
|
|
WIP_F_MST
|
Stop/Move
|
Windshield wiper stop position signal input
• Stop: Windshield wipers stop at normal position
• Move: Windshield wipers do not stop at normal position
|
If windshield wipers are operating, Move-Stop is repeated.
|
2AA (Autostop switch signal)
|
|
WIP_F_RY_HI
|
Off/On
|
Windshield wiper HI relay output signal
• Off: Windshield wiper HI relay is off.
• On: Windshield wiper HI relay is on.
|
—
|
3C, 3E (Windshield wiper motor (HI) control)
|
|
WIP_F_RY_LO
|
Off/On
|
Windshield wiper relay LO output signal
• Off: Windshield wiper LO relay is off.
• On: Windshield wiper LO relay is on.
|
—
|
3G, 3I (Windshield wiper motor (LOW) control)
|
|
WIP_R
|
OFF/LOW/INT
|
Rear wiper operation condition input signal from start stop unit
• OFF: Rear wiper switch is in OFF position.
• LOW: Rear wiper switch is in ON position.
• INT: Rear wiper switch is in INT position.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|
|
WIP_R_RY
|
Off/On
|
Rear wiper relay drive signal
• Off: Rear wiper motor is not operated.
• On: Rear wiper motor is operated.
|
—
|
• 2I (CAN_L)
• 2K (CAN_H)
|