PID/DATA MONITOR INSPECTION (i-stop) [SKYACTIV-G 2.5T]
id1102b4000100
1. Connect the M-MDS to the DLC-2.
2. After vehicle identification is completed, select the following from the M-MDS initial screen.
3. Select the applicable item from the PID/DATA Monitor Table.
4. Verify the monitored value according to the directions on the screen.
PID/DATA Monitor Table
Module |
Item (definition) |
Unit/Condition |
Page |
---|---|---|---|
PCM
|
APP
|
%
|
|
APP1
|
%
|
||
APP2
|
%
|
||
BARO
|
kPa {MPa}, mBar {Bar}, psi, in H20
|
||
BATT_CUR
|
A
|
||
BATT_RES
|
Not applicable
|
||
BATT_SOC
|
%
|
||
BATT_TEMP
|
°C, °F
|
||
BATT_V
|
V
|
||
BBP
|
kPa {MPa}, mBar {Bar}, psi, in H20
|
||
BFP
|
kPa {MPa}, mBar {Bar}, psi, in H20
|
||
BOO
|
High/Low
|
||
BPA
|
High/Low
|
||
ECT
|
°C, °F
|
||
IAT
|
°C, °F
|
||
I-Stop_OFF
|
Off/On
|
||
I-Stop_TRD
|
Off/On
|
||
I-Stop_VSP
|
Off/On
|
||
I-Stop_VST
|
Off/On
|
||
M_GEAR
|
Neutral / 1st gear / 2nd gear / 3rd gear / 4th gear / 5th gear / 6th gear / Reverse / Undefined / Auto / In_Progress / YSF / Error
|
||
VPWR
|
V
|
||
DSC HU/CM
|
BRAKE_SW
|
Off/On
|
|
BRK_F_P_C
|
kPa {MPa}, mBar {Bar}, psi, in H20
|
||
LON_ACCL_C
|
G
|
||
WSPD_SEN_LF
|
KPH, MPH
|
||
WSPD_SEN_LR
|
KPH, MPH
|
||
WSPD_SEN_RF
|
KPH, MPH
|
||
WSPD_SEN_RR
|
KPH, MPH
|
||
TCM
|
I-Stop_EST
|
Off/On
|
|
TFT
|
°C, °F
|
||
TR
|
P / SHIFT_DOWN / SHIFT_UP / M / D / N / R
|
||
EPS control module
|
STR_AB_EST
|
°(deg)
|
|
STR_ROT_SPD
|
°/s
|
||
STR_TRQ_S_M
|
Nm
|
||
Climate control unit
|
STOP_ST
|
Available / Not Available / Error
|
|
SAS control module
|
SEAT_B_D
|
Unbuckled / Buckled
|
|
Rear body control module (RBCM)
|
DOOR_ALL
|
Close/OPEN
|
|
DOOR_D
|
Close/OPEN
|
||
HOOD
|
Close/OPEN
|
||
TRUNK
|
Close/OPEN
|
||
Start stop unit
|
RELAY_ACC
|
Off/On
|
(See FOREWORD [START STOP UNIT].)
|
RELAY_IG1
|
Off/On
|
||
RELAY_IG2
|
Off/On
|
||
SSB_1
|
Off/On
|
||
SSB_2
|
Off/On
|
||
VPWR_ACC
|
V
|
||
VPWR_B1
|
V
|
||
VPWR_IG1
|
V
|