MAP IS NOT DISPLAYED [ENTERTAINMENT SYSTEM (WITH CENTER DISPLAY) (TYPE-A)]

id160309001500

Description

MAP IS NOT DISPLAYED

•  Navigation map is not displayed

Possible Causes

•  SD card malfunction

•  Auxiliary jack/USB port/SD card slot hub malfunction

•  Connectivity master unit (CMU) malfunction

Diagnostic Procedure

Step

Inspection

Action

1

VERIFY DTCs

•  Is a DTC displayed?
(See DTC INSPECTION [CONNECTIVITY MASTER UNIT (TYPE-A)].)

Yes

Perform the applicable DTC troubleshooting.

(See DTC TABLE [CONNECTIVITY MASTER UNIT (TYPE-A) (E)].)

No

Go to the next step.

2

VERIFY SD CARD TAB

•  Switch the ignition OFF (LOCK).

•  Remove the SD card.

•  Is the SD card tab unlocked?

Caution

•  If the SD card tab condition is verified with the ignition switched ON (engine off or on), the SD card could be damaged. Verify the SD card tab condition with the ignition switched OFF (LOCK).

Yes

Go to the next step.

No

Unlock the tab on the SD card, then go to the next step. (Navigation cannot be launched with the tab locked)

3

VERIFY SD CARD IDENTIFICATION CONDITION

•  Insert the SD card.

•  Lock the doors and leave the vehicle for 5 min or more. (to stop the system completely)

•  Unlock the doors (door closed) and start the engine.

•  Wait until FM or compass screen is displayed in the center display. (to wait for the connectivity master unit (CMU) to launch)

•  Is [SD CARD INSERTED] displayed in the center display?

Yes

•  Only [SD CARD INSERTED] is displayed:

―  Go to the next step.

•  [INVALID SD CARD] is displayed subsequently:

―  Replace the SD card, then go to Step 6.

No

Go to the next step.

4

VERIFY NAVIGATION OPERATION

•  Start the engine.

•  Operate the NAVI button.

•  Is the map displayed in the center display?

Yes

System is normal.

Symptom troubleshooting is completed.

No

Go to the next step.

5

RESTART CONNECTIVITY MASTER UNIT (CMU) SYSTEM AND VERIFY IF MALFUNCTION RECURS

•  Disconnect the negative battery terminal and wait for 1 min or more.
(Refer to the [NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION] in the workshop manual.)

•  Connect the negative battery terminal.
(Refer to the [NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION] in the workshop manual.)

•  Switch the ignition OFF (LOCK).

•  Lock the doors and leave the vehicle for 5 min or more.

•  Unlock the doors and start the engine.

•  Wait until FM or compass screen is displayed in the center display.

•  Insert the SD card.

•  Is [SD CARD INSERTED] displayed in the center display?

Yes

Replace the connectivity master unit (CMU), then go to the next step.

(Refer to the [CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION] in the workshop manual.)

No

Replace the auxiliary jack/USB port/SD card slot hub, then go to the next step.

(Refer to the [AUXILIARY JACK/USB PORT/SD CARD SLOT HUB REMOVAL/INSTALLATION] in the workshop manual.)

6

VERIFY NAVIGATION OPERATION

•  Operate the NAVI button.

•  Is the map displayed in the center display?

Yes

System is normal.

Symptom troubleshooting is completed.

No

Repeat the diagnosis from Step 1.

•  If the malfunction recurs, replace the connectivity master unit (CMU).
(Refer to the [CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION] in the workshop manual.)

Description	MAP IS NOT DISPLAYED
Description	• Navigation map is not displayed
Possible Causes	• SD card malfunction • Auxiliary jack/USB port/SD card slot hub malfunction • Connectivity master unit (CMU) malfunction

Step	Inspection		Action
1	VERIFY DTCs • Is a DTC displayed? (See DTC INSPECTION [CONNECTIVITY MASTER UNIT (TYPE-A)].)	Yes	Perform the applicable DTC troubleshooting. (See DTC TABLE [CONNECTIVITY MASTER UNIT (TYPE-A) (E)].)
1		No	Go to the next step.
2	VERIFY SD CARD TAB • Switch the ignition OFF (LOCK). • Remove the SD card. • Is the SD card tab unlocked? Caution • If the SD card tab condition is verified with the ignition switched ON (engine off or on), the SD card could be damaged. Verify the SD card tab condition with the ignition switched OFF (LOCK).	Yes	Go to the next step.
2		No	Unlock the tab on the SD card, then go to the next step. (Navigation cannot be launched with the tab locked)
3	VERIFY SD CARD IDENTIFICATION CONDITION • Insert the SD card. • Lock the doors and leave the vehicle for 5 min or more. (to stop the system completely) • Unlock the doors (door closed) and start the engine. • Wait until FM or compass screen is displayed in the center display. (to wait for the connectivity master unit (CMU) to launch) • Is [SD CARD INSERTED] displayed in the center display?	Yes	• Only [SD CARD INSERTED] is displayed: ― Go to the next step. • [INVALID SD CARD] is displayed subsequently: ― Replace the SD card, then go to Step 6.
3		No	Go to the next step.
4	VERIFY NAVIGATION OPERATION • Start the engine. • Operate the NAVI button. • Is the map displayed in the center display?	Yes	System is normal. Symptom troubleshooting is completed.
4		No	Go to the next step.
5	RESTART CONNECTIVITY MASTER UNIT (CMU) SYSTEM AND VERIFY IF MALFUNCTION RECURS • Disconnect the negative battery terminal and wait for 1 min or more. (Refer to the [NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION] in the workshop manual.) • Connect the negative battery terminal. (Refer to the [NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION] in the workshop manual.) • Switch the ignition OFF (LOCK). • Lock the doors and leave the vehicle for 5 min or more. • Unlock the doors and start the engine. • Wait until FM or compass screen is displayed in the center display. • Insert the SD card. • Is [SD CARD INSERTED] displayed in the center display?	Yes	Replace the connectivity master unit (CMU), then go to the next step. (Refer to the [CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION] in the workshop manual.)
5		No	Replace the auxiliary jack/USB port/SD card slot hub, then go to the next step. (Refer to the [AUXILIARY JACK/USB PORT/SD CARD SLOT HUB REMOVAL/INSTALLATION] in the workshop manual.)
6	VERIFY NAVIGATION OPERATION • Operate the NAVI button. • Is the map displayed in the center display?	Yes	System is normal. Symptom troubleshooting is completed.
6		No	Repeat the diagnosis from Step 1. • If the malfunction recurs, replace the connectivity master unit (CMU). (Refer to the [CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION] in the workshop manual.)