CYLINDER BLOCK (I) ASSEMBLYSM1759379
CYLINDER BLOCK (I) ASSEMBLY

E6U011010300E04

1.Assemble in the order indicated in the table.
e6u110zeb016

1
Oil jet valve
2
Upper main bearing, thrust bearing
3
Crankshaft
4
Lower main bearing
5
Main bearing cap
(See Main Bearing Cap Assembly Note.)
6
Connecting rod
7
Piston
8
Piston pin
(See Piston Pin Assembly Note.)
9
Snap ring
10
Piston ring
(See Piston Ring Assembly Note.)
11
Upper connecting rod bearing
(See Connecting Rod Bearing Assembly Note.)
12
Connecting rod, piston
(See Piston Assembly Note.)
13
Lower connecting rod bearing
(See Connecting Rod Bearing Assembly Note.)
14
Connecting rod cap
(See Connecting Rod Cap Assembly Note.)
15
Engine balancer
(See Balancer Unit Assembly Note.)
16
Pilot bearing (If equipped)
(See Pilot Bearing Assembly Note.)


Main Bearing Cap Assembly Note

1.Tighten the crank bearing caps in the order shown in the figure.
b3e0110e267
Tightening procedure
(1) Apply engine oil to all bolts.
(2) 3—7 N·m {30.6—71.3 kgf·cm, 26.6—61.9 in·lbf}
(3) 23—27 N·m {2.4—2.7 kgf·m, 17—19.9 ft·lbf}
(4) 38—42 N·m {3.9—4.2 kgf·m, 28.1—30.9 ft·lbf}
(5) Loosen all the bolts (until bolts are torque-free).
(6) 3—7 N·m {30.6—71.3 kgf·cm, 26.6—61.9 in·lbf}
(7) 18—22 N·m {1.9—2.2 kgf·m, 13.3—16.2 ft·lbf}
(8) 87.5°—92.5°


Piston Pin Assembly Note

1.Assemble the piston pin using the SST.
e6u110zeb034
Note
• Assemble the piston pin so that the front marks of the piston and the connecting rod are positioned on the same surface.
belbze00000212


Piston Ring Assembly Note

1.Assemble the oil ring.

2.Assemble the second ring with the notch facing downward.

3.Assemble the top ring with scraper face side upward.
c3u0110e256


Piston Assembly Note

1.Position the end gap of each ring so they are not aligned as shown in the figure.
e6u110zeb004

2.Insert the piston into the cylinder with the arrow on top of the piston facing the front of the engine.
b3e0110e108


Connecting Rod Bearing Assembly Note

1.Install the connecting rod bearing to the connecting rod and connecting rod caps as shown in the figure.
b3e0110e109


Connecting Rod Cap Assembly Note

Caution
• When assembling the connecting rod caps, align the broken, rough faces of the connecting rods and connecting rod caps.

1.Tighten the connecting rod installation bolts using the following procedure.

Tightening procedure
(1) 26—31 N·m {2.7—3.1 kgf·m, 19.2—22.8 ft·lbf}
(2) 80°—100°


Balancer Unit Assembly Note

Caution
• The balancer unit cannot be disassembled due to the precision interior construction of the balancer unit.

1.Visually inspect the balancer unit gear for damage and verify that the shaft rotates smoothly.

• If there is any malfunction, replace the balancer unit.

2.Remove the cylinder block lower blind plug and install the SST.
e6u110zwb050

3.Rotate the crankshaft in the direction of engine rotation so that the No. 1 cylinder is at top dead center (TDC). (Until the counterweight contacts the SST and stops.)

Note
• If the cylinder block, crankshaft, crankshaft main bearing, and balancer unit are not replaced, use the adjustment shim as it is. In this case, go to Step 12.

4.Assemble the master shims (No. 50) to the shim seating face of the balancer unit at the angles shown in the figure.
b3e110ze4061
Caution
• Engage the gears slowly and place the balancer unit on the cylinder block while being careful not to contact the balancer unit gear strongly with the crankshaft drive gear and damage it.

5.With the balancer unit marks at the exact top center positions, assemble the balancer unit to the cylinder block and tighten the bolts in a criss-cross pattern in two steps.
b3e0110e111
Tightening torque
1st step: 25 N·m {2.5 kgf·m, 18 ft·lbt}
2nd step: 44—46 N·m {4.5—4.6 kgf·m, 32.5—33.9 ft·lbf}

6.Remove the SST installed in Step 2.

7.Measure the gear backlash using the following procedure.

(1) Place the ATDC marks 10 °, 30 °, 100 °, 190 °, 210 °, 280 ° on the rear side of the crankshaft to indicate the angles.
(2)Insert a flathead screwdriver into the crankshaft No.1 counterweight area and set both the rotation and the thrust direction with the flathead screwdriver, using a prying action, as shown in the figure for accurate measurement of the backlash.
b3e0110e113
(3)Set the SST and a dial gauge as shown in the figure.
b3e110ze4062
(4)Rotate the driven gear to the left and right so that the crankshaft drive gear and balancer unit gear contact each other lightly.
(5)When measuring the backlash, rotate the crankshaft one full rotation and measure the backlash at 6 locations (A to F) as shown in the figure.
b3e110ze4064

8.Select the adjustment shim from the selection table based on the measured minimum value of the backlash.

Adjustment shim selection table

Backlash

mm {IN.EN_UK}

Selection shim (No.)

Shim thickness mm {IN.EN_UK}

Backlash

mm {IN.EN_UK}

Selection shim (No.)

Shim thickness mm {IN.EN_UK}
0.267—0.273 {0.01051—0.01074}
15
1.15 {0.0452}
0.127—0.133 {0.00500—0.00523}
35
1.35 {0.0531}
0.260—0.266 {0.01023—0.01047}
16
1.16 {0.0456}
0.120—0.126 {0.00472—0.00496}
36
1.36 {0.0535}
0.253—0.259 {0.00996—0.01019}
17
1.17 {0.0460}
0.113—0.119 {0.00444—0.00468}
37
1.37 {0.0539}
0.246—0.252 {0.00968—0.00992}
18
1.18 {0.0464}
0.106—0.112 {0.00417—0.00440}
38
1.38{0.0543}
0.239—0.245 {0.00940—0.00964}
19
1.19 {0.0468}
0.099—0.105 {0.00389—0.00413}
39
1.39 {0.0547}
0.232—0.238 {0.00913—0.00937}
20
1.20 {0.0472}
0.092—0.098
.087 {0.00362—0.00385}
40
1.40 {0.0551}
0.225—0.231 {0.00885—0.00909}
21
1.21 {0.0476}
0.085—0.091 {0.00334—0.00358}
41
1.41 {0.0555}
0.218—0.224 {0.00858—0.00881}
22
1.22 {0.0480}
0.078—0.084 {0.00307—0.00330}
42
1.42 {0.0559}
0.211—0.217 {0.00830—0.00854}
23
1.23 {0.0484}
0.071—0.077 {0.00279—0.00303}
43
1.43 {0.0562}
0.204—0.210 {0.00803—0.00826}
24
1.24 {0.0488}
0.064—0.070 {0.00251—0.00275}
44
1.44 {0.0566}
0.197—0.203 {0.00775—0.00799}
25
1.25 {0.492}
0.057—0.063 {0.00224—0.00248}
45
1.45 {0.0570}
0.190—0.196 {0.00748—0.00771}
26
1.26 {0.496}
0.050—0.056 {0.00196—0.00220}
46
1.46 {0.0574}
0.183—0.189 {0.00720—0.00744}
27
1.27 {0.499}
0.043—0.049 {0.00169—0.00192}
47
1.47 {0.0578}
0.176—0.182 {0.00692—0.00716}
28
1.28 {0.503}
0.036—0.042 {0.00141—0.00165}
48
1.48 {0.0582}
0.169—0.175 {0.00665—0.00688}
29
1.29 {0.507}
0.029—0.035 {0.00114—0.00137}
49
1.49 {0.0586}
0.162—0.168 {0.00637—0.00661}
30
1.30 {0.511}
0.022—0.028 {0.000866—0.00110}
50 (master)
1.50 {0.0590}
0.155—0.161 {0.00610—0.00633}
31
1.31 {0.515}
0.015—0.021 {0.00059—0.000826}
51
1.51 {0.0594}
0.148—0.154 {0.00582—0.00606}
32
1.32 {0.519}
0.008—0.014 {0.000314—0.000551}
52
1.52 {0.0598}
0.141—0.147 {0.00555—0.00578}
33
1.33 {0.523}
0.001—0.007 {0.00003—0.000275}
53
1.53 {0.0602}
0.134—0.140 {0.00527—0.00551}
34
1.34 {0.527}
0.000—0.000 {0.000—0.000}
54
1.54 {0.0606}

9.Verify that the No. 1 cylinder is at TDC.

• If not aligned, perform Steps 2—3.

10.Remove the master shim from the balancer unit and assemble the selected adjustment shim at the angles shown in the figure.
b3e110ze4061

11.Perform Steps 5—7.

12.Verify that the measured backlash is within the specified range.

• If the backlash exceeds the maximum specification, replace the adjustment shim and repeat Steps 4—12.
Measured backlash maximum
0.01—0.1 mm {0.0004—0.0039 In}


Pilot Bearing Assembly Note

1.Assemble the pilot bearing using the corresponding 20 mm {0.79 in} side of a Snap-on brand millimeter size bushing driver set A160M adapter A160M7 (20—22 mm {0.79—0.86 in}) or substitution tool.

Substitution tool
Outer diameter: 21 mm {0.83 in}
Inner diameter: 19 mm {0.75 in}
e6e110zecl049
c3u0510w013