id011000503600

1.Remove the engine front cover lower blind plug.

beleue00000039

2.Remove the engine front cover upper blind plug.

beleue00000040

3.Remove the cylinder block lower blind plug, and install the SST.

abatjw00000791

4.Rotate the crankshaft in the direction of the engine rotation so that the No.1 piston is at TDC of the compression stroke. (Until the counterweight contacts SST and stops.)

5.Loosen the timing chain using the following procedure:

(1)Insert a suitable bolt (M6 X 1.0, length 25—35 mm {0.99—1.3 in}) into the engine front cover upper blind plug and tighten it until it contacts the chain tensioner arm, and then rotate it back one turn. (Set the bolt slightly away from the chain tensioner arm so that it does not contact it.)

beleue00000041

(2)Using the cast hexagon on the exhaust camshaft, apply force counterclockwise to facilitate unlocking the chain tensioner ratchet.

am8rrw00002539

(3)Using a Hex bit socket (2.5 mm {0.098 in}) or T15 Torx bit socket, unlock the chain tensioner ratchet so that it can be lifted up.

am8rrw00002540

(4)Using the cast hexagon on the exhaust camshaft, apply force in the direction of the engine rotation to increase tension on the chain.

am8rrw00002541

Note

• The chain tensioner rack is compressed using the chain tension generated by applying force to the exhaust camshaft in the direction of the engine rotation.

beleue00000042

Note

• The racket has not been unlocked if the bolt cannot be pressed in approx. 5 mm {0.2 in}.

(5)Screw in the bolt set in Step 1 approx. 5 mm {0.2 in} and secure the tensioner arm with the rack compressed.

am6xuw00002058

• If the tensioner arm cannot be secured, return the bolt to its original position and repeat the procedure from Step 3.

6.Fix the exhaust camshaft using a wrench on the cast hexagon, and loosen the camshaft sprocket installation bolt.

am3zzw00002423

Caution

• Perform the work carefully so that the washer does not drop out.

7.Remove the exhaust camshaft sprocket installation bolt, exhaust camshaft sprocket, and washer as a single unit.

beleue00000044

8.Remove the OCV.

beleue00000078

Note

• The camshaft caps are to be kept ordered for correct reassembly in their original positions. Do not mix the caps.

9.Loosen the camshaft cap bolts in two or three steps in the order shown in the figure and remove the camshaft cap.

beleue00000079

10.Remove the camshafts for the intake and exhaust sides.

11.Remove the tappet.

12.Install an appropriate tappet based on the results of the valve clearance inspection.

Selected tappet = Removed tappet thickness + Measured valve clearance - Standard valve clearance

Standard valve clearance [Engine cold]

IN: 0.22—0.28 mm {0.009—0.011 in}

EX: 0.27—0.33 mm {0.011—0.012 in}

13.Verify that No.1 cylinder is at TDC of the compression stroke. (Position counterweight contacts SST.)

14.Apply the gear oil (SAE No.90 or equivalent) to each journal of the cylinder head as shown in the figure.

am6zzw00002188

15.Install the camshaft with No.1 cylinder aligned with the TDC position.

16.Apply the gear oil (SAE No.90 or equivalent) to each journal of the camshaft as shown in the figure.

am6zzw00002281

17.Temporarily tighten the camshaft cap bolts evenly in 2—3 steps.

18.Tighten the camshaft cap bolts in the order shown in the following two steps.

beleue00000080

Tightening procedure

1. 5.0—9.0 N·m {51—91 kgf·cm, 45—79 in·lbf}

2. 14—17 N·m {1.5—1.7 kgf·m, 11—12 ft·lbf}

19.Install the OCV.

beleue00000078

Tightening torque

8—11 N·m {82—112 kgf·cm, 71—97 in·lbf}

Caution

• Install a washer to the fourth or fifth thread of the exhaust camshaft sprocket bolt being careful not to drop the washer.

• Do not tighten the camshaft sprocket installation bolt at this stage. Verify the valve timing before performing the bolt tightening.

20.Install the exhaust camshaft sprocket installation bolt, exhaust camshaft sprocket, and a new washer as a single unit.

am8rrw00002545

21.Install the SST on the camshaft as shown in the figure.

beleue00000047

22.Remove the installation bolt for the engine front cover upper blind plug (M6 X 1.0 length 25—35mm {1.0—1.3 in}), and apply tension to the timing chain.

23.Fix the exhaust camshaft using a wrench on the cast hexagon, and tighten the sprocket installation bolt.

24.Remove the SST from the camshaft.

25.Remove the SST installed in the cylinder block lower blind plug hole.

26.Rotate the crankshaft clockwise two turns and inspect the valve timing.

• If not aligned, repeat the procedure from 21.

27.Install the cylinder block lower blind plug.

beleue00000048

Tightening torque

18—22 N·m {1.9—2.2 kgf·m, 14—16 ft·lbf}

28.Apply the silicone sealant and install the engine front cover upper blind plug.

beleue00000040

Tightening torque

8.0—11.5 N·m {82—117 kgf·cm, 71—101 in·lbf}

29.Install a new engine front cover lower blind plug.

beleue00000039

Tightening torque

10—14 N·m {102—142 kgf·cm, 89—123 in·lbf}