LOW AND REVERSE BRAKE AND ONE-WAY CLUTCH INNER RACE DISASSEMBLY/ASSEMBLYSM1759134
LOW AND REVERSE BRAKE AND ONE-WAY CLUTCH INNER RACE DISASSEMBLY/ASSEMBLY

D6E051719500A05

1.Perform the preinspection before disassembly.

(See Low and Reverse Brake Preinspection.)

2.Disassemble in the order indicated in the table.

3.Assemble in the reverse order of disassembly.
D6E517ZA5042

1
Snap ring
2
Retaining plate
3
Drive and driven plates
4
Dish plate
5
Snap ring
(See Snap Ring Disassembly Note.)
6
One-way clutch inner race
7
Piston return spring
8
Low and reverse brake piston
(See Low and Reverse Brake Piston Disassembly Note.)


Snap Ring Disassembly Note

1.Install the SSTs as shown.
D6J517ZA40542
Caution
• Depress the one-way clutch inner race only enough to remove the snap ring.
Overpressing will damage the one-way clutch inner race assembly edges.

2.Compress the one-way clutch inner race.

3.Remove the snap ring.

4.Remove the SSTs and remove one-way clutch inner race and the piston return spring.


Low and Reverse Brake Piston Disassembly Note

• Remove the low and reverse brake piston by applying compressed air through the fluid passage.
D6E517ZA50433
Air pressure
98.1 kPa {1.0 kgf/cm 2, 14 psi} max.

Assembly Procedure

1.Measure the facing thickness in three places, and determine the average of the three readings.

Low and reverse brake drive plate thickness
Standard: 1.60 mm {0.063 in}
Minimum: 1.45 mm {0.057 in}
• If not within the specification, replace the drive plates.
Caution
• Installing the low and reverse brake piston may damage its seal. Carefully install the low and reverse brake piston by pushing evenly around the circumference.

2.Apply ATF to the circumference of the low and reverse brake piston seal, and install the piston to the transaxle case.

3.Install the piston return spring and one-way clutch to the transaxle case.
D6E517ZA50444

4.Install the SSTs as shown.
D6J517ZA40545
Caution
• Depress the one-way clutch inner race only enough to install the snap ring.
Overpressing will damage the one-way clutch inner race assembly edges.

5.Compress the one-way clutch inner race.
D6E517ZA50456
Caution
• The transaxle body may be damaged if installed incorrectly. Make sure to install the transaxle body in such a way that the end of the snap ring does not enter the area shown in the figure.

6.Install the snap ring.

7.Remove the SSTs.

8.Install the dish plate.

9.Install the drive and driven plates in the following order.

Driven-Drive-Driven-Drive-Driven-Drive-Driven-Drive-Driven-Drive

10.Install the retaining plate and the snap ring.
D6E517ZA50467

11.Measure the low and reverse brake clearance.

(1) Set the dial gauge to the low and reverse brake.
(2) Set the measuring point of the dial gauge to the low and reverse brake piston.
B3E0517A1338
(3) Apply compressed air to the part indicated in the figure and let the low and reverse brake piston stroke three times.
D6E517ZA50439
Air pressure
98.1 kPa {1.0 kgf/cm 2, 14 psi}
(4) Apply compressed air and operate the low and reverse brake piston. Read the value when the indicator of the dial gauge stops.
(5) Release the compressed air and read the dial gauge when the low and reverse brake piston is not operating.
(6) Calculate the low and reverse brake clearance according to the following formula:
Step (4) value-Step (5) value= low and reverse brake clearance.
(7) Measure the clearances at four locations (90° apart) by following the steps from (3) to (6). Verify that the average value is within the specification below.
D6E517ZA504710
Low and reverse brake clearance
2.20-2.50 mm {0.087-0.098 in}
• If not within the specification, remove the snap ring and measure its thickness.
(8) Add the thickness to the average value calculated in step (7), and select the snap ring whose range includes the value.

Snap ring size for low and reverse brake clearance

Range mm {IN.EN_UK}

Snap ring sizes mm {IN.EN_UK}

4.050-4.250 {0.159-0.167}
1.8 {0.071}
4.250-4.450 {0.167-0.175}
2.0 {0.079}
4.450-4.650 {0.175-0.183}
2.2 {0.087}
4.650-4.850 {0.183-0.190}
2.4 {0.094}
4.850-5.050 {0.190-0.199}
2.6 {0.102}
5.050-5.250 {0.199-0.207}
2.8 {0.110}
5.250-5.450 {0.207-0.215}
3.0 {0.118}

(9) Install the selected snap ring and perform steps (2) to (7) again. Verify that the calculated value satisfies the clearance specification.

12.Inspect the low and reverse brake operation by applying compressed air as shown.
D6E517ZA504311
Air pressure
98.1 kPa {1.0 kgf/cm 2, 14 psi}