DTC P0192:00 [L3 Turbo]

DTC P0192:00 [L3 Turbo]SM2444034

id0102b7147700

DTC P0192:00	Fuel pressure sensor circuit low input
DETECTION CONDITION	• If the input voltage from the fuel pressure sensor is less than 0.19 V for 5.3 s, the PCM determines that the fuel pressure sensor circuit is low. Diagnostic support note • This is a continuous monitor (CCM). • The MIL illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • DTCs are stored in the PCM memory.
POSSIBLE CAUSE	• Fuel pressure sensor connector or terminals malfunction • Short to ground in wiring harness between the following terminals: ― Fuel pressure sensor terminal C—PCM terminal 2K ― Fuel pressure sensor terminal B—PCM terminal 2R • PCM connector or terminals malfunction • Fuel pressure sensor signal circuit and ground circuit are shorted to each other • Open circuit in wiring harness between fuel pressure sensor terminal C and PCM terminal 2K • Fuel pressure sensor malfunction • PCM malfunction

Diagnostic procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT FUEL PRESSURE SENSOR CONNECTOR CONDITION • Turn the ignition switch off. • Disconnect the fuel pressure sensor connector. • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
3		No	Go to the next step.
4	INSPECT FUEL PRESSURE SENSOR CIRCUIT FOR SHORT TO GROUND • Fuel pressure sensor connector is disconnected. • Inspect for continuity between the following terminals (wiring harness-side) and body ground: ― Fuel pressure sensor terminal C ― Fuel pressure sensor terminal B • Is there continuity?	Yes	If the short to ground circuit could be detected: • Repair or replace the wiring harness for a possible short to ground. If the short to ground circuit could not be detected: • Replace the PCM (short to ground in PCM internal circuit). (See PCM REMOVAL/INSTALLATION [L3 Turbo].) Go to Step 9.
4		No	Go to the next step.
5	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
5		No	Go to the next step.
6	INSPECT FUEL PRESSURE SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER • Fuel pressure sensor and PCM connectors are disconnected. • Inspect for continuity between fuel pressure sensor terminals B and A (wiring harness-side). • Is there continuity?	Yes	Repair or replace the wiring harness for a possible short to each other, then go to Step 9.
6		No	Go to the next step.
7	INSPECT FUEL PRESSURE SENSOR POWER SUPPLY CIRCUIT FOR OPEN CIRCUIT • Fuel pressure sensor and PCM connectors are disconnected. • Inspect for continuity between fuel pressure sensor terminal C (wiring harness-side) and PCM terminal 2K (wiring harness-side). • Is there continuity?	Yes	Go to the next step.
7		No	Repair or replace the wiring harness for a possible open circuit, then go to Step 9.
8	INSPECT FUEL PRESSURE SENSOR • Inspect the fuel pressure sensor. (See FUEL PRESSURE SENSOR INSPECTION [L3 Turbo].) • Is there any malfunction ?	Yes	Replace the fuel delivery pipe, then go to the next step. (See FUEL INJECTOR REMOVAL/INSTALLATION [L3 Turbo].)
8		No	Go to the next step.
9	VERIFY DTC TROUBLESHOOTING COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [L3 Turbo].) • Start the engine. • Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST [L3 Turbo].) • Is the same DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [L3 Turbo].)
9		No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [L3 Turbo].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [L3 Turbo].)
10		No	DTC troubleshooting completed.