DTC P0101:00 [L3 Turbo]

DTC P0101:00	MAF sensor circuit range/performance problem
DETECTION CONDITION	• When the conditions are as follows, the PCM compares the intake airflow amount with the estimated intake airflow amount (calculated from the barometric pressure, MAP sensor and throttle opening angle). MONITORING CONDITIONS ― Engine speed: 500—4,500 rpm ― Barometric pressure: 105—180 kPa {1.08—1.83 kgf/cm², 15.3—26.1 psi} ― Throttle position−throttle position before 25 ms: below 1.22% (boost air temperature less than 20 °C {68 °F}), below 30% (boost air temperature more than 20 °C {68 °F}) ― Battery voltage: above 8 V • If over a period continuing for 5 s, the cumulative value of the intake airflow amount divided by the estimated intake airflow amount is 1.35 or more, the PCM determines that the detected mass air flow amount is above is too high. • If over a period continuing for 5 s, the cumulative value of the intake airflow amount divided by the estimated intake airflow amount is 0.65 or less, the PCM determines that the detected mass air flow amount is above is too low. Diagnostic support note • This is a continuous monitor (CCM). • MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM. • PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • DTCs are stored in the PCM memory.
POSSIBLE CAUSE	• Air restriction or leakage in intake-air system (between MAF sensor and intake manifold) • MAF sensor malfunction • Turbocharger malfunction (turbine wheel/compressor damaged, stuck) • MAF/IAT sensor connector or terminals malfunction • Electrical corrosion in MAF/IAT RETURN circuit • Voltage drops in the ground circuit • PCM connector or terminals malfunction • PCM malfunction

DTC P0101:00

MAF sensor circuit range/performance problem

DETECTION CONDITION

• When the conditions are as follows, the PCM compares the intake airflow amount with the estimated intake airflow amount (calculated from the barometric pressure, MAP sensor and throttle opening angle).

MONITORING CONDITIONS

― Engine speed: 500—4,500 rpm

― Barometric pressure: 105—180 kPa {1.08—1.83 kgf/cm², 15.3—26.1 psi}

― Throttle position−throttle position before 25 ms: below 1.22% (boost air temperature less than 20 °C {68 °F}), below 30% (boost air temperature more than 20 °C {68 °F})

― Battery voltage: above 8 V

• If over a period continuing for 5 s, the cumulative value of the intake airflow amount divided by the estimated intake airflow amount is 1.35 or more, the PCM determines that the detected mass air flow amount is above is too high.

• If over a period continuing for 5 s, the cumulative value of the intake airflow amount divided by the estimated intake airflow amount is 0.65 or less, the PCM determines that the detected mass air flow amount is above is too low.

Diagnostic support note

• This is a continuous monitor (CCM).

• MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.

• PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.

• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

• DTCs are stored in the PCM memory.

POSSIBLE CAUSE

• Air restriction or leakage in intake-air system (between MAF sensor and intake manifold)

• MAF sensor malfunction

• Turbocharger malfunction (turbine wheel/compressor damaged, stuck)

• MAF/IAT sensor connector or terminals malfunction

• Electrical corrosion in MAF/IAT RETURN circuit

• Voltage drops in the ground circuit

• PCM connector or terminals malfunction

• PCM malfunction

STEP	INSPECTION	ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
No	Go to the next step.
3	VERIFY CURRENT INPUT SIGNAL STATUS IS CONCERN INTERMITTENT OR CONSTANT • Start the engine. • Access the following PIDs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [L3 Turbo].) ― ECT ― MAF ― TP ― RPM • Warm-up the engine until the ECT PID value is above 70 °C {158 °F}. • Idle the engine for 5 s or more. Caution • While driving, always operate the vehicle in a safe and lawful manner. • Drive the vehicle under the following two conditions: Condition 1 ― TP PID: 50—87.5% ― RPM PID: above 1,000 rpm ― 4th gear (MTX), D range (ATX) Condition 2 ― TP PID: above 80% ― RPM PID: below 2,000 rpm ― gear in • Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [L3 Turbo].) • Is the PENDING CODE for this DTC present?	Yes	Go to the next step.
No	Intermittent concern exists. • Perform the “INTERMITTENT CONCERN TROUBLESHOOTING” procedure. (See INTERMITTENT CONCERN TROUBLESHOOTING [L3 Turbo].)
4	INSPECT MAF PID • Start the engine. • Access the MAF PID using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [L3 Turbo].) • Race the engine and verify that the MAF PID changes quickly according to the change in the engine speed. • Is the MAF PID response normal? (See PCM INSPECTION [L3 Turbo].)	Yes	Go to Step 7.
No	Go to the next step.
5	INSPECT AIR RESTRICTION OR LEAKAGE AT INTAKE-AIR SYSTEM • Inspect for air leakage and restrict between MAF sensor and intake manifold. • Is there any malfunction?	Yes	Repair or replace the malfunctioning part according to the inspection results, then go to Step 9.
No	Go to the next step.
6	INSPECT TURBOCHARGER • Inspect the turbocharger. (See TURBOCHARGER INSPECTION [L3 Turbo].) • Is there any malfunction?	Yes	Replace the turbocharger, then go to Step 9. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L3 Turbo].)
No	Replace the MAF/IAT sensor, then go to Step 9. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L3 Turbo].)
7	INSPECT MAF/IAT SENSOR TERMINALS FOR ELECTRICAL CORROSION • Turn the ignition switch off. • Disconnect the MAF/IAT sensor connector. • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
No	Inspect the MAF/IAT RETURN circuit and ground circuit. • If the circuit has a malfunction: ― Repair or replace the suspected wiring harness, then go to Step 9. • If the circuit is normal: ― Go to the next step.
8	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to the next step.
No	Go to the next step.
9	VERIFY DTC TROUBLESHOOTING COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [L3 Turbo].) • Start the engine. • Warm-up the engine until the ECT PID value is above 70 °C {158 °F}. • Idle the engine for 5 s or more. Caution • While performing the Drive Mode, always operate the vehicle in a safe and lawful manner. • Drive the vehicle under the following two conditions: Condition 1 ― TP PID: 50—87.5% ― RPM PID: above 1,000 rpm ― 4th gear (MTX), D range (ATX) Condition 2 ― TP PID: above 80% ― RPM PID: below 2,000 rpm ― gear in • Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [L3 Turbo].) • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [L3 Turbo].)
No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [L3 Turbo].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [L3 Turbo].)
No	DTC troubleshooting completed.

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED

• Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?

Yes

Go to the next step.

Record the FREEZE FRAME DATA (Mode 2)/snapshot data on repair order, then go to the next step.

VERIFY RELATED SERVICE INFORMATION AVAILABILITY

• Verify related Service Information availability.

• Is any related Service Information available?

Yes

Perform repair or diagnosis according to the available Service Information.

• If the vehicle is not repaired, go to the next step.

Go to the next step.

VERIFY CURRENT INPUT SIGNAL STATUS IS CONCERN INTERMITTENT OR CONSTANT

• Start the engine.

• Access the following PIDs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [L3 Turbo].)

― ECT

― MAF

― TP

― RPM

• Warm-up the engine until the ECT PID value is above 70 °C {158 °F}.

• Idle the engine for 5 s or more.

Caution

• While driving, always operate the vehicle in a safe and lawful manner.

• Drive the vehicle under the following two conditions:

Condition 1

― TP PID: 50—87.5%

― RPM PID: above 1,000 rpm

― 4th gear (MTX), D range (ATX)

Condition 2

― TP PID: above 80%

― RPM PID: below 2,000 rpm

― gear in

• Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [L3 Turbo].)

• Is the PENDING CODE for this DTC present?

Yes

Go to the next step.

Intermittent concern exists.

• Perform the “INTERMITTENT CONCERN TROUBLESHOOTING” procedure. (See INTERMITTENT CONCERN TROUBLESHOOTING [L3 Turbo].)

INSPECT MAF PID

• Start the engine.

• Access the MAF PID using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [L3 Turbo].)

• Race the engine and verify that the MAF PID changes quickly according to the change in the engine speed.

• Is the MAF PID response normal? (See PCM INSPECTION [L3 Turbo].)

Yes

Go to Step 7.

Go to the next step.

INSPECT AIR RESTRICTION OR LEAKAGE AT INTAKE-AIR SYSTEM

• Inspect for air leakage and restrict between MAF sensor and intake manifold.

• Is there any malfunction?

Yes

Repair or replace the malfunctioning part according to the inspection results, then go to Step 9.

Go to the next step.

INSPECT TURBOCHARGER

• Inspect the turbocharger. (See TURBOCHARGER INSPECTION [L3 Turbo].)

• Is there any malfunction?

Yes

Replace the turbocharger, then go to Step 9.

(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L3 Turbo].)

Replace the MAF/IAT sensor, then go to Step 9.

(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L3 Turbo].)

INSPECT MAF/IAT SENSOR TERMINALS FOR ELECTRICAL CORROSION

• Turn the ignition switch off.

• Disconnect the MAF/IAT sensor connector.

• Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).

• Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 9.

Inspect the MAF/IAT RETURN circuit and ground circuit.

• If the circuit has a malfunction:

― Repair or replace the suspected wiring harness, then go to Step 9.

• If the circuit is normal:

― Go to the next step.

INSPECT PCM CONNECTOR CONDITION

• Disconnect the PCM connector.

• Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).

• Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to the next step.

Go to the next step.

VERIFY DTC TROUBLESHOOTING COMPLETED

• Make sure to reconnect all disconnected connectors.

• Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [L3 Turbo].)

• Start the engine.

• Warm-up the engine until the ECT PID value is above 70 °C {158 °F}.

• Idle the engine for 5 s or more.

Caution

• While performing the Drive Mode, always operate the vehicle in a safe and lawful manner.

• Drive the vehicle under the following two conditions:

Condition 1

― TP PID: 50—87.5%

― RPM PID: above 1,000 rpm

― 4th gear (MTX), D range (ATX)

Condition 2

― TP PID: above 80%

― RPM PID: below 2,000 rpm

― gear in

• Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [L3 Turbo].)

• Is the PENDING CODE for this DTC present?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [L3 Turbo].)

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

• Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [L3 Turbo].)

• Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [L3 Turbo].)

DTC troubleshooting completed.