Item
Specification
Ignition timing
Approx. BTDC 10°
Idle mixture
HC concentration: Within the regulation
CO concentration: Within the regulation
Standard valve clearance [Engine cold]
IN: 0.22—0.28 mm {0.0087—0.011 in}
EX: 0.27—0.33 mm {0.011—0.012 in}
Compression
Standard: 1,280 kPa {13.1 kgf/cm
2, 185.65 psi}[250rpm]
Minimum: 896 kPa {9.14 kgf/cm
2, 129.96 psi}[250rpm]
Maximum difference between cylinders: 196.1 kPa {2.0 kgf/cm
2, 28.5 psi}
OCV resistance
6.9—7.9 ohms [20°C {68°F}]
Cylinder head bolt length
Standard: 144.7—145.3 mm {5.697—5.720 in}
Maximum: 146 mm {5.74 in}
Front oil seal press-in amount
0—0.5 mm {0—0.019 in}
Engine oil capacity (approx. quantity)
Oil replacement: 5.3 L {5.6 US qt, 4.7 Imp qt}
Oil and oil filter replacement: 5.7 L {6.0 US qt, 5.0 Imp qt}
Total (dry engine): 6.4 L {6.8 US qt, 5.6 Imp qt}
Oil pressure (reference value) [oil temperature: 100 °C {212 °F}]
297—551 kPa {3.03—5.61 kgf/cm
2, 43.1—79.9 psi} [3,000 rpm]
Engine coolant capacity (approx. quantity)
9.0 L {9.5 US qt, 7.9 Imp qt}
Cooling system cap valve opening pressure
112.8—142.2 kPa {1.15—1.45 kgf/cm
2, 16.4—20.6 psi}
Thermostat initial-opening temperature
80—84 °C {176—183 °F}
Thermostat full-open temperature
97 °C {207 °F}
Thermostat full-open lift
More than 8.0 mm {0.31 in}
Cooling fan motor No.1, No.2 standard current
17.5—22.5 A [12 V]
Fuel pressure
410—490 kPa {4.19—4.99 kgf/cm
2, 59.5—71.0 psi}
Fuel hold pressure
230 kPa {2.35 kgf/cm
2, 33.4 psi} or more
Fuel injector resistance
1.0—1.2 ohms [20 °C {68 °F}]
Battery electrolyte specific gravity [20 °C {68 °F}]
1.22—1.29
Battery load test current
55D23L (48 A·h/5HR, 55 A·h/20HR): 180 A
75D23L (52 A·h/5HR, 65 A·h/20HR): 195 A
80D26L (55 A·h/5HR, 65 A·h/20HR): 195 A
Battery parasitic draw (When the ignition is off (key is removed), all doors and the bonnet are closed.)
55—65 mA
Battery slow charge current
55D23L (48 A·h/5HR, 55 A·h/20HR): 4.5—5.5 A
75D23L (52 A·h/5HR, 65 A·h/20HR): 5.0—6.0 A
80D26L (55 A·h/5HR, 65 A·h/20HR): 5.5—6.5 A
Battery quick charge current [30 min]
55D23L (48 A·h/5HR, 55 A·h/20HR): 30 A
75D23L (52 A·h/5HR, 65 A·h/20HR): 35 A
80D26L (55 A·h/5HR, 65 A·h/20HR): 35 A
Generator standard voltage [IG-ON]
Terminal B: B+
Terminal P: Approx. 1 V or less
Terminal D: Approx. 0 V
Generator standard voltage [Idle, 20 °C {68 °F}]
Terminal B: 13—15 V
Terminal P: Approx. 3—8 V
Terminal D: Turn the electrical loads (headlights, blower motor, rear window defroster, brake lights, etc.) on and verify that the voltage reading increases.
Generator generated current minimum value
70 % of the nominal output current (nominal output current: 110 A)
[Ambient temp. 20 °C {68 °F}, voltage 13.0—15.0 V, both engine and generator are hot]
Generator rotor resistance (between slip rings) [20 °C {68 °F}]
1.8—2.2 ohm
Generator brush length
Standard: 22.5 mm {0.89 in}
Minimum: 5.0 mm {0.20 in}
Generator brush spring force
Standard: 4.1—5.3 N {0.42—0.54 kgf, 0.92—1.19 lbf}
Minimum: 1.7 N {0.17 kgf, 0.38 lbf}
Firing order
1-3-4-2 (all cylinders independent firing)
Spark plug type
L3BD 18 110, L3YD 18 110
Spark plug gap
Standard: 0.60—0.80 mm {0.024—0.031 in}
New spark plug (reference): 0.60—0.70 mm {0.024—0.027 in}
Spark plug resistance [25°C {77 °F}]
3.0—7.5 kilohms
Starter no-load test voltage
11 V
Starter no-load test current
90 A or less
Starter pinion gap
0.5—2.0 mm {0.02—0.07 in}
Starter armature runout
0.1 mm {0.004 in} max.
Starter commutator diameter
Standard: 29.4 mm {1.16 in}
Minimum: 28.8 mm {1.13 in}
Segment groove depth of starter commutator
Standard: 0.5 mm {0.02 in}
Minimum: 0.2 mm {0.008 in}
Starter brush length
Standard: 12.3 mm {0.48 in}
Minimum: 5.5 mm {0.22 in}
Starter brush spring force
Standard: 15.0—20.4 N {1.53—2.08 kgf, 3.38—4.58 lbf}
Minimum: 2.75 N {0.280 kgf, 0.618 lbf}