id0213008010d3

Caution

• Performing the following procedures without first removing the ABS wheel-speed sensor may possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the following procedures, remove the ABS wheel-speed sensor (axle side) and fix it to an appropriate place where the sensor will not be pulled by mistake while servicing the vehicle.

• Secure the steering wheel using tape or a cable to prevent the steering shaft from rotating after disconnecting the steering shaft. If the steering wheel rotates after the steering shaft and the steering gear and linkage are disconnected, the internal parts of the clock spring could be damaged.

1.Remove the side cover and under cover.

2.Drain the power steering fluid. (See POWER STEERING FLUID INSPECTION [L3 Turbo, L5].)

3.Remove the front auto leveling sensor. (Vehicle with front auto leveling sensor) (See FRONT AUTO LEVELING SENSOR REMOVAL/INSTALLATION.)

4.Remove the transverse member. (See TRANSVERSE MEMBER REMOVAL/INSTALLATION.)

5.Remove the intermediate shaft installation bolt, and disconnect the steering shaft. (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)

6.Remove in the order indicated in the table.

7.Install in the reverse order of removal.

8.When replace the front crossmember, inspect the front wheel alignment and adjust it if necessary. (See FRONT WHEEL ALIGNMENT.)

acxwzw00001379

Tie-rod End Ball Joint Removal Note

1.Remove the tie-rod end ball joint locknut.

2.Disconnect the tie-rod end ball joint using the SST.

acxaaw00001609

Steering Gear And Linkage, Front Stabilizer, Front Lower Arm And Front Crossmember Component Removal Note

1.Support the crossmember component with a jack.

acxaaw00001610

2.Loosen the bolts of the No.1 engine mount (engine side).

L3 Turbo

acxuuw00001689

L5

acxwzw00001610

3.Remove the No.1 engine mount bolt (engine side).

L3 Turbo

acxuuw00001690

L5

acxwzw00001478

4.Lower the steering gear and linkage, front stabilizer, front lower arm and front crossmember component slightly.

5.Disconnect the following parts.

acxaaw00001611

― Eye connector (pump side)

― Pressure hose clip

― Return hose clamp

Front Crossmember Mounting Rubber (front) Installation Note

1.Install the front crossmember mounting rubber (front) so that the smaller outer diameter is facing upward.

acxaaw00001612

Front Crossmember Mounting Rubber (rear) Installation Note

1.Install the front crossmember mounting rubber (rear) so that the larger outer diameter is facing upward.

acxaaw00001613

No. 1 Engine Mount Installation Note

1.Temporarily tighten the No.1 engine mount bolt (crossmember side).

Steering Gear And Linkage, Front Stabilizer, Front Lower Arm And Front Crossmember Component Installation Note

1.Raise the steering gear and linkage, front stabilizer, front lower arm and front crossmember component to the appropriately level, and install the following parts.

acxaaw00001611

― Eye connector (pump side)

― Pressure hose clip

― Return hose clamp

2.Install the steering gear and linkage, front stabilizer, front lower arm and front crossmember component.

3.Temporarily install the No.1 engine mount bolt C in the figure.

L3 Turbo

acxaaw00001590

L5

acxwzw00001611

4.Tighten the No.1 engine mount bracket bolt A and B in order of A→B.

L3 Turbo

acxaaw00001592

L5

am8rrw00002662

5.Fully tighten the bolt C.

Note

• Bolt C can be tightened on the nut side. When tightening on the nut side, tighten it according to the following tightening torque.

• The tightening torque when tightening from the bolt side is different than when doing it from the nut side because the amount of force required to tighten the bolt differs. These differences in force applied to the bolt are because of the differences in the surface treatment of the nut and bolt.

L3 Turbo

acxaaw00001589

L5

acxwzw00001612

6.Tighten the No.1 engine mount bolt D (crossmember side).