SOLENOID VALVE INSPECTION [FS5A-EL]SM2445485
SOLENOID VALVE INSPECTION [FS5A-EL]

id051721293100

Caution
• Water or foreign objects entering the connector can cause a poor connection or corrosion. Be sure not to drop water or foreign objects on the connector when disconnecting it.

Primary Control Valve Body


On-vehicle inspection

1.Disconnect the coupler component connector.

(1)Disconnect the negative battery cable.
(2)Remove the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L5].)
(3)Disconnect the coupler component connector.
am8rrw00002353

2.Measure the resistance between the coupler component terminals.
am8rrw00002354
• If there is any malfunction, inspect the coupler component for continuity. If coupler component has no malfunction, perform the “Off-vehicle inspection“. (See Off-Vehicle inspection.)

Solenoid valve specification

Solenoid valve

Terminal

Resistance (ohm)
Pressure control solenoid A
D↔I
2.4—7.3
Shift solenoid A
A↔GND
1.0—4.2
Shift solenoid B
C↔GND
1.0—4.2
Shift solenoid C
G↔GND
1.0—4.2
Shift solenoid D
B↔GND
10.9—26.2
Shift solenoid E
F↔GND
10.9—26.2


Operating inspection

Caution
• Do not apply battery position voltage to terminals for more than 3 s.
Note
• Because the operation sound of the solenoid valve is small, perform inspection in a quiet place.

1.Disconnect the coupler component connector.

(1)Disconnect the negative battery cable.
(2)Remove the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L5].)
(3)Disconnect the coupler component connector.
am8rrw00002353

2.Apply battery positive voltage to the coupler component terminals A, B, C, F or G and battery negative voltage to GND, and verify that operating sound is heard from solenoid valve.
am8rrw00002354
• If the operation sound is not heard, inspect the coupler component for continuity. If coupler component has no malfunction, perform the “Off-vehicle inspection“. (See Off-Vehicle inspection.)

3.Apply battery positive voltage to the coupler component terminal D and battery negative voltage to terminal I, and verify that operating sound is heard from solenoid valve.
am8rrw00002354
• If the operation sound is not heard, inspect the coupler component for continuity. If coupler component has no malfunction, perform the “Off-vehicle inspection“. (See Off-Vehicle inspection.)


Off-Vehicle inspection

1.Measure the resistance between the coupler component terminals.

• If there is any malfunction, replace the solenoid valve. (See SOLENOID VALVE REMOVAL/INSTALLATION [FS5A-EL].)
am8rrw00002355
Pressure control solenoid A specification
2.4—7.3 ohms
am8rrw00002356
Shift solenoid A, B, C specification
1.0—4.2 ohms
am8rrw00002357
Shift solenoid D, E specification
10.9—26.2 ohms


Secondary Control Valve Body


On-vehicle inspection

1.Disconnect the coupler component connector.

(1)Disconnect the negative battery cable.
(2)Disconnect the coupler component connector.
am8rrw00002358

2.Measure the resistance between the coupler component terminals A and B.
am8rrw00002359
• If there is any malfunction, inspect the coupler component for continuity. If coupler component has no malfunction, perform the “Off-vehicle inspection“. (See Off-Vehicle inspection.)

Solenoid valve specification

Solenoid valve

Terminal

Resistance (ohm)
Pressure control solenoid B
A↔GND
1.0—4.2
Shift solenoid F
B↔GND
8.4—21.8


Operating inspection

Caution
• Do not apply battery position voltage to terminals for more than 3 s.
Note
• Because the operation sound of the solenoid valve is small, perform inspection in a quiet place.

1.Disconnect the coupler component connector.

(1)Disconnect the negative battery cable.
(2)Disconnect the coupler component connector.
am8rrw00002358

2.Apply battery positive voltage to the coupler component terminals A, B and battery negative voltage to GND, and verify that operating sound is heard from solenoid valve.
am8rrw00002359
• If the operation sound is not heard, inspect the coupler component for continuity. If coupler component has no malfunction, perform the “Off-vehicle inspection“. (See Off-Vehicle inspection.)


Off-Vehicle inspection

1.Measure the resistance between the coupler component terminals.

• If there is any malfunction, replace the solenoid valve. (See SOLENOID VALVE REMOVAL/INSTALLATION [FS5A-EL].)
am8rrw00002360
Pressure control solenoid B specification
1.0—4.2 ohms
am8rrw00002361
Shift solenoid F specification
8.4—21.8 ohms