NO.8 DISPLAY DOES NOT CHANGE TO THE REAR MOUNT CAMERA IMAGE [CAR-NAVIGATION SYSTEM (INTEGRATED MULTI INFORMATION DISPLAY)]

NO.8 DISPLAY DOES NOT CHANGE TO THE REAR MOUNT CAMERA IMAGE [CAR-NAVIGATION SYSTEM (INTEGRATED MULTI INFORMATION DISPLAY)]SM2446158

id0903h3945200

8	Display does not change to the rear mount camera image
POSSIBLE CAUSE	• Rear mount camera malfunction • Poor connection of the rear mount camera connector, terminal damage • Poor connection of the multi information display connector, terminal damage • Open or short circuit in wiring harness between multi information display and rear mount camera • Open or short circuit in reverse signal wiring harness • Multi information display malfunction

Diagnostic procedure

STEP	INSPECTION		ACTION
1	• Is the lens of the rear mount camera dirty or view is obstructed?	Yes	Clean the lens of the rear mount camera or remove the obstruction.
1		No	Go to the next step.
2	• Does the lens of the rear mount camera have a crack and damage?	Yes	Replace the rear mount camera. (See REAR MOUNT CAMERA REMOVAL/INSTALLATION.)
2		No	Go to the next step.
3	• Retrieve the TCM, instrument cluster and multi information display DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FS5A-EL].) (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [AW6A-EL, AW6AX-EL].) (See DTC INSPECTION [INSTRUMENT CLUSTER].) (See DTC INSPECTION [MULTI INFORMATION DISPLAY].) • Is there any DTC displayed?	Yes	Perform the applicable DTC diagnosis procedure. (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [FS5A-EL].) (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [AW6A-EL, AW6AX-EL].) (See DTC TABLE [INSTRUMENT CLUSTER].) (See DTC TABLE [MULTI INFORMATION DISPLAY].)
3		No	Go to the next step.
4	• Turn the ignition switch to the LOCK position. • Remove the rear mount camera. • Inspect the connection of the rear mount camera connector (4-pin). • Inspect both the rear mount camera and wiring harness-side connector for poor connection (such as damaged/pulled-out pins, corrosion). • Are all the pins normal?	Yes	Go to the next step.
4		No	If poor connection of rear mount camera connector: • Securely connect the rear mount camera connector. If the rear mount camera connector is wrong: • Replace the rear mount camera. (See REAR MOUNT CAMERA REMOVAL/INSTALLATION.) If the wiring harness-side connector is wrong: • Repair or replace the pins and/or the connector.
5	• Turn the ignition switch to the LOCK position. • Remove the multi information display. • Inspect the connection of the multi information display connector (24-pin). • Disconnect the multi information display connector (24-pin). • Inspect both the multi information display connector terminal for poor connection (such as damaged/pulled-out pins, corrosion). • Are all the pins normal?	Yes	Go to the next step.
5		No	If poor connection of multi information display connector: • Securely connect the multi information display connector. If the multi information display connector is wrong: • Replace the multi information display. (See MULTI INFORMATION DISPLAY REMOVAL/INSTALLATION.) If the wiring harness-side connector is wrong: • Repair or replace the pins and/or the connector.
6	• Inspect the following wiring harnesses between the multi information display and rear mount camera. ― Terminal 1L (24-pin, POWER)—terminal A (4-pin, POWER) ― Terminal 1R (24-pin, P-GND)—terminal B (4-pin, P-GND) ― Terminal 1M (24-pin, V-GND)—terminal C (4-pin, V-GND) ― Terminal 1K (24-pin, COMPOSITE)—terminal D (4-pin, COMPOSITE) • Is there open or short circuit?	Yes	Go to the next step.
6		No	Inspect the suspect wiring harness. Repair or replace if necessary.
7	• Access the TCM PID TR using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FS5A-EL].) (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [AW6A-EL, AW6AX-EL].) • Shift the selector lever all position and ranges. • Is the PID value properly?	Yes	Replace the rear mount camera, then inspect generating of malfunction symptom. (See REAR MOUNT CAMERA REMOVAL/INSTALLATION.) Even if it exchanges rear mount camera, when a fault phenomenon occurs: • Replace the multi information display. (See MULTI INFORMATION DISPLAY REMOVAL/INSTALLATION.) • Reinspect the malfunction symptom, then repeat from Step 1 if malfunction recurs.
7		No	Repair or replace malfunctioning part according to inspection result. Reinspect the malfunction symptom, then repeat from Step 1 if malfunction recurs.