id091900801600

1.Disconnect the negative battery cable.

2.Remove the mudguard (RH).

3.Disconnect rear washer hose A from the washer tank.

4.Remove rear washer hose A from clip A.

acxuuw00001822

5.Disconnect joint pipe A and remove rear washer hose A.

6.Remove the following parts:

(1)Brake boot (MTX) (See CONSOLE REMOVAL/INSTALLATION.)

(2)Console panel (See CONSOLE PANEL REMOVAL/INSTALLATION.)

(3)Shift lever knob (See SHIFT MECHANISM REMOVAL/INSTALLATION [A26MX-R].)

(4)Console (See CONSOLE REMOVAL/INSTALLATION.)

(5)Front scuff plate inner (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

(6)Front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)

(7)Dashboard under cover

(8)Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

(9)Bonnet release lever (See BONNET LATCH AND RELEASE LEVER REMOVAL/INSTALLATION.)

(10)Lower panel (See LOWER PANEL REMOVAL/INSTALLATION.)

(11)Decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION.)

(12)Center panel (See CENTER PANEL REMOVAL/INSTALLATION.)

(13)Audio unit (See AUDIO UNIT REMOVAL/INSTALLATION.)

(14)Climate control unit (See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [FULL-AUTO AIR CONDITIONER].) (See CLIMATE CONTROL UNIT REMOVAL [MANUAL AIR CONDITIONER].) (See CLIMATE CONTROL UNIT INSTALLATION [MANUAL AIR CONDITIONER].)

(15)Meter hood (See METER HOOD REMOVAL/INSTALLATION.)

(16)Column cover (See COLUMN COVER REMOVAL/INSTALLATION.)

(17)Instrument cluster (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)

(18)Driver-side air bag module (See DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION.)

(19)Steering wheel (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)

(20)Combination switch (See COMBINATION SWITCH REMOVAL/INSTALLATION.)

(21)Steering shaft (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)

(22)A-pillar lower trim (See A-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)

(23)A-pillar trim (See A-PILLAR TRIM REMOVAL/INSTALLATION.)

(24)Dashboard (See DASHBOARD REMOVAL/INSTALLATION.)

7.Disconnect joint pipe B and remove rear washer hose B.

8.Disconnect joint pipe C and remove rear washer hose C.

9.Remove rear washer hose C from clips B.

10.Disconnect joint pipe D and remove rear washer hose C.

11.Detach clips B.

12.Remove the following parts:

(1)Rear scuff plate inner (See REAR SCUFF PLATE REMOVAL/INSTALLATION.)

(2)B-pillar lower trim (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)

(3)Front seat belt upper anchor installation bolt (See FRONT SEAT BELT REMOVAL/INSTALLATION.)

(4)B-pillar upper trim (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)

(5)Rear seat (See REAR SEAT REMOVAL/INSTALLATION.)

(6)Sub trunk box (See SUB TRUNK BOX REMOVAL/INSTALLATION.)

(7)Trunk end trim (See TRUNK END TRIM REMOVAL/INSTALLATION.)

(8)Trunk side trim (See TRUNK SIDE TRIM REMOVAL/INSTALLATION.)

(9)C-pillar trim (See C-PILLAR TRIM REMOVAL/INSTALLATION.)

(10)D-pillar trim (See D-PILLAR TRIM REMOVAL/INSTALLATION.)

(11)Map light (See MAP LIGHT REMOVAL/INSTALLATION.)

(12)Sunvisor (See SUNVISOR REMOVAL/INSTALLATION.)

(13)Assist handle (See ASSIST HANDLE REMOVAL/INSTALLATION.)

13.Disconnect joint pipe E.

acxuuw00001823

14.Remove the headliner. (See HEADLINER REMOVAL/INSTALLATION.)

15.Remove rear washer hose D from clips C and D.

16.Cut the urethane of the headliner and remove the tape and rear washer hose D.

Note

• After installing the rear washer hose, reinforce the urethane that was cut when removing.

17.Remove rear washer hose E from the rear washer nozzle.

18.Install in the reverse order of removal.