ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [AY6A-EL, AY6AX-EL]

id0502k1290100


Reading DTCs Procedure

1.  Connect the M-MDS(IDS) to the DLC-2.

ac9uuw00003915

2.  After the vehicle is identified, select the following items from the initialization screen of the IDS.

(1)  Select "Self Test".
(2)  Select "Modules".
(3)  Select "TCM".

Note
•  Freeze frame data/snapshot data appears at the top of the help screen when the displayed DTC is selected.
Freeze frame data
―  The freeze frame data consists of data for vehicle and transaxle control system operation conditions when malfunctions in the transaxle control system are detected and stored in the TCM.
―  Freeze frame data is stored at the instant the malfunction indicator lamp illuminates, and only a part of the DTC data is stored.
Snapshot data
―  The snap shot data stores the currently detected DTC data.
―  The recording timing for the freeze frame data/snap shot data differs depending on the number of DTC drive cycles.
•  For a DTC with a drive cycle number 1, only the malfunction determination data is recorded.
•  For a DTC with a drive cycle number 2, both the malfunction determination and undetermined data is recorded.

Freeze frame data table

Note
•  Refer to PID monitor table for confirm the transaxle control system operation status while the TCM does not store the DTC. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [AY6A-EL, AY6AX-EL].)
•  Freeze frame data items are not displayed, according to detected DTC.

Freeze frame data item

Unit

Data contents

Corresponding data monitor items
LOAD
%
Charging efficiency
LOAD
ECT
°C {°F}
Engine coolant temperature
ECT
RPM
RPM
Engine speed
RPM
VS
KPH {MPH}
Vehicle speed
VSS
TP
%
Throttle position sensor
THOP
RUNTM
hh:mm:ss
Time since engine start
—
VPWR
V
Power supply voltage
VPWR


Snapshot data table

Note
•  Refer to PID monitor table for confirm the transaxle control system operation status while the TCM does not store the DTC. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [AY6A-EL, AY6AX-EL].)
•  Snapshot data items are not displayed, according to detected DTC.

Snap shot data item

Unit

Data contents

Corresponding data monitor items
LOAD
%
Charging efficiency
LOAD
ECT
°C {°F}
Engine coolant temperature
ECT
RPM
RPM
Engine speed
RPM
VSS
KPH {MPH}
Vehicle speed
VSS
TP1
%
Throttle position sensor
THOP
EG_RUN_TIME
hh:mm:ss
Time since engine start
—
VPWR
V
Power supply voltage
VPWR

3.  Verify the DTC according to the directions on the screen.

•  If any DTCs are displayed, perform troubleshooting according to the corresponding DTC inspection. (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [AY6A-EL, AY6AX-EL].)

4.  After completion of repairs, clear all DTCs stored in the TCM. (See Clearing DTCs Procedure.)


Clearing DTCs Procedure

1.  Connect the M-MDS(IDS) to the DLC-2.

ac9uuw00003915

2.  After the vehicle is identified, select the following items from the initialization screen of the IDS.

(1)  Select "Self Test".
(2)  Select "Modules".
(3)  Select "TCM".

3.  Verify the DTC according to the directions on the screen.

4.  Press the clear button on the DTC screen to clear the DTC.

5.  Switch the ignition OFF (LOCK).

6.  Switch the ignition ON and wait for 5 s or more.

7.  Perform DTC inspection. (See Reading DTCs Procedure.)

8.  Verify that no DTCs are displayed.