|
DTC No.
|
On-board diagnostic function
|
Detection condition
|
Fail-safe
|
|
P0601
|
Flash ROM malfunction
|
• Flash ROM (in TCM) internal circuit malfunction is detected.
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0603
|
EEPROM malfunction
|
• Different numeric values for EEPRROM and RAM (in TCM) are detected.
|
N/A
|
|
P0604
|
RAM malfunction
|
• RAM (in TCM) read/write error is detected.
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0707
|
Transmission range (TR) switch circuit low input (short to ground)
|
• TR switch position voltage input to TCM is less than 0.127 V when ignition switch is at ON position.
|
• D range is determined when there is no TR switch signal input.
• Inhibits slope mode control
|
|
P0708
|
Transmission range (TR) switch circuit high input (open circuit)
|
• Vehicle speed is 30 km/h {18.6 mph} or more, and no range signal is input from the TR switch.
|
• D range is determined when there is no TR switch signal input.
• Inhibits slope mode control
|
|
P0711
|
Transmission fluid temperature (TFT) sensor malfunction (stuck)
|
• Change in ATF temperature cannot be detected for 10 min or more when driving in D range.
|
• Fixes ATF temperature value at 80 °C {176 °F}
• Inhibits slope mode control
• Inhibits self learning control
|
|
P0712
|
Transmission fluid temperature (TFT) sensor circuit malfunction (short to ground)
|
• TCM detects ATF temperature of 200 °C {392 °F} or more.
|
• Fixes ATF temperature value at 80 °C {176 °F}
• Inhibits slope mode control
• Inhibits self learning control
|
|
P0713
|
Transmission fluid temperature (TFT) sensor circuit malfunction (short to power/open circuit)
|
• TCM detects ATF temperature of less than -43 °C {-45.4 °F} when engine is warmed-up and running.
|
• Fixes ATF temperature value at 80 °C {176 °F}
• Inhibits slope mode control
• Inhibits self learning control
|
|
P0717
|
Turbine sensor circuit malfunction (open circuit/short circuit)
|
• Turbine speed signal is not input during vehicle speed signal 12 pulse period when driving in D range.
|
• Substitutes vehicle speed signal for turbine speed signal.
• Inhibits 5GR and 6GR
• Inhibits self learning control
• Inhibits driver adaptive shift control
|
|
P0722
|
Vehicle speed sensor (VSS) circuit malfunction (open circuit/short circuit)
|
• Vehicle speed signal is not input during turbine speed signal 12 pulse period when driving in D range.
|
• Substitutes turbine speed signal for vehicle speed signal.
• Inhibits 5GR and 6GR
• Inhibits self learning control
• Inhibits driver adaptive shift control
|
|
P0751
|
Shift solenoid A malfunction (stuck off)
|
• TCM detects that shift solenoid A does not change from off when engine is running
|
• Inhibits 4GR, 5GR and 6GR
• Inhibits 1GR and 2GR (manual mode)
|
|
P0752
|
Shift solenoid A malfunction (stuck on)
|
• TCM detects that shift solenoid A does not change from on when engine is running
|
N/A
|
|
P0756
|
Shift solenoid B malfunction (stuck off)
|
• TCM detects that shift solenoid B does not change from off when engine is running
|
N/A
|
|
P0757
|
Shift solenoid B malfunction (stuck on)
|
• TCM detects that shift solenoid B does not change from on when engine is running
|
N/A
|
|
P0761
|
Shift solenoid C malfunction (stuck off)
|
• TMC detects that shift solenoid C does not change from off when engine is running
|
N/A
|
|
P0762
|
Shift solenoid C malfunction (stuck on)
|
• TMC detects that shift solenoid C doe not change from on when engine is running
|
• Inhibits 4GR, 5GR and 6GR
|
|
P0766
|
Shift solenoid D malfunction (stuck off)
|
• TCM detects that shift solenoid D does not change from off when engine is running
|
• Inhibits 4GR, 5GR and 6GR
|
|
Shift solenoid G malfunction (stuck on)
|
• TCM detects that shift solenoid G does not change from on when engine is running
|
• Inhibits 4GR, 5GR and 6GR
|
|
P0781
|
1-2 shift valve malfunction
|
• TCM detects 1-2 shift valve malfunction.
|
• Inhibits 4GR, 5GR and 6GR
• Inhibits 1GR and 2GR (manual mode)
|
|
P0813
|
Reverse sequence valve malfunction
|
• TCM detects reverse sequence valve malfunction.
|
• Inhibits 6GR
|
|
P0819
|
Manual switch/up switch/down switch circuit malfunction (open circuit/short circuit)
|
M range switch circuit malfunction
• M range switch remains on for 2 s or more except in D range.
|
• Inhibits manual mode control
|
|
Up switch or down switch circuit malfunction
• When all of the following conditions are met:
-
- M range switch off.
-
- Except D range
-
- Up or down switch remains on for 10 s or more.
|
• Inhibits manual mode control using selector lever
|
|
P0826
|
Steering shift switch circuit malfunction (open circuit/short to ground)
|
• TCM detects short circuit or short to ground in steering shift switch circuit when engine is running.
|
• Inhibits manual mode control
|
|
P0882
|
TCM B+ low (less than 9 V)
|
• Voltage of less than 9 V detected at TCM terminals 1AD when engine is running.
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0883
|
TCM B+ low (less than 11 V)
|
• Voltage of less than 11 V detected at TCM terminals 1AD when engine is running.
|
• Inhibits self learning control
|
|
P0961
|
Line pressure control solenoid range/performance (stuck)
|
• Feedback current corresponding to solenoid current command value is irregular when engine is running.
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0962
|
Line pressure control solenoid circuit malfunction (short to ground/open circuit)
|
• Open or short circuit in line pressure control solenoid signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0963
|
Line pressure control solenoid circuit malfunction (short to power)
|
• Short circuit in line pressure control solenoid signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0969
|
Shift solenoid F range/performance (stuck)
|
• Feedback current corresponding to solenoid current command value is irregular when engine is running.
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0970
|
Shift solenoid F circuit malfunction (short to ground/open circuit)
|
• Open or short circuit in shift solenoid F signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0971
|
Shift solenoid F circuit malfunction (short to power)
|
• Short circuit in shift solenoid F signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits N-D shift pressure control
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0973
|
Shift solenoid A circuit malfunction (short to ground)
|
• Short to ground in shift solenoid A signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0974
|
Shift solenoid A circuit malfunction (short to power/open circuit)
|
• Open or short circuit in shift solenoid A signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0976
|
Shift solenoid B circuit malfunction (short to ground)
|
• Short to ground in shift solenoid B signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0977
|
Shift solenoid B circuit malfunction (short to power/open circuit)
|
• Open or short circuit in shift solenoid B signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0979
|
Shift solenoid C circuit malfunction (short to ground)
|
• Short to ground in shift solenoid C signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0980
|
Shift solenoid C circuit malfunction (short to power/open circuit)
|
• Open or short circuit in shift solenoid C signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0982
|
Shift solenoid D circuit malfunction (short to ground)
|
• Short to ground in shift solenoid D signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0983
|
Shift solenoid D circuit malfunction (short to power/open circuit)
|
• Open or short circuit in shift solenoid D signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0985
|
Shift solenoid E circuit malfunction (short to ground)
|
• Short to ground in shift solenoid E signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P0986
|
Shift solenoid E circuit malfunction (short to power/open circuit)
|
• Open or short circuit in shift solenoid E signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P2719
|
Shift solenoid G range/performance (stuck)
|
• Feedback current corresponding to solenoid current command value is irregular when engine is running.
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P2720
|
Shift solenoid G circuit malfunction (short to ground/open circuit)
|
• Open or short circuit in shift solenoid G signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P2721
|
Shift solenoid G circuit malfunction (short to power)
|
• Short circuit in shift solenoid G signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
|
|
P2757
|
Torque converter clutch (TCC) stuck off
|
• TCM detects that TCC control solenoid does not change from on when engine is running
|
• Inhibits acceleration from 2GR
|
|
P2758
|
Torque converter clutch (TCC) stuck on
|
• TCM detects that TCC control solenoid does not change from off when engine is running
|
N/A
|
|
P2762
|
TCC control solenoid range/performance (stuck)
|
• Feedback current corresponding to solenoid current command value is irregular when engine is running.
|
• Inhibits acceleration from 2GR
• Inhibits TCC control
|
|
P2763
|
TCC control solenoid circuit malfunction (short to power)
|
• Short circuit in TCC control solenoid signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Inhibits acceleration from 2GR
• Inhibits TCC control
|
|
P2764
|
TCC control solenoid circuit malfunction (short to ground/open circuit)
|
• Open or short circuit in TCC control solenoid signal system (while TCM monitors solenoid output voltage, the voltage that differs from the signal output by CPU in TCM is detected).
|
• Inhibits acceleration from 2GR
• Inhibits TCC control
|
|
U0073
|
CAN BUS OFF
|
• Bus off error is detected.
|
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
• Inhibits 5GR, 6GR
|
|
U0100
|
TCM cannot receive any signals from PCM
|
• Communication error is detected between TCM and PCM.
|
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
• Inhibits 5GR, 6GR
|