CLIMATE CONTROL UNIT INSPECTION [MANUAL AIR CONDITIONER]


id0740008022a2

1.  Turn the ignition switch to the ON position.

2.  Connect the negative (-) lead of the tester to body ground.

3.  By inserting the positive (+) lead of the tester into each climate control unit terminal, measure the voltage according to the terminal voltage table.

•  If there is any malfunction, inspect the parts under “Inspection item (s)”.
―  If the parts under “Inspection item (s)” are found to be normal, replace the climate control unit.


Terminal Voltage Table (Reference)

e5u740zw5103

Terminal

Signal name

Connected to

Measurement condition

Voltage (V)

Inspection item (s)

A
IG2
A/C 7.5 A fuse
IG SW ON
B+
•  Wiring harness: continuity, short circuit (Climate control unit— fuse: A—A/C 7.5 A)
•  A/C 7.5 A fuse
IG SW LOCK
1.0 or less
•  Wiring harness: continuity, short circuit (Climate control unit— fuse: A—A/C 7.5 A)
B
B+
ROOM 15 A fuse
Under any condition
B+
•  Wiring harness: continuity, short circuit (Climate control unit— fuse: B—ROOM 15 A)
•  ROOM 15 A fuse
C
Blower fan speed control
Power MOS FET
Fan stopped
1.0 or less
•  Wiring harness: continuity, short circuit (Climate control unit—power MOS FET: C—C)
•  Power MOS FET
Fan: manual 1 (LO) —24
2.7—3.4
Fan: manual 25 (HI)
9.6
D
TNS signal
TNS relay
Headlight switch OFF
1.0 or less
•  Wiring harness: short circuit (Climate control unit—TNS relay: D—D)
•  TNS relay
•  Headlight switch
Headlight switch ON
B+
•  Wiring harness: continuity, short circuit (Climate control unit—TNS relay: D—D)
•  TNS relay
•  Headlight switch
E
Blower motor feedback
Power MOS FET
Fan stopped
B+
1.  Wiring harness: continuity, short circuit (Climate control unit—power MOS FET: E—B)
2.  Power MOS FET
3.  Blower motor
4.  Blower relay
5.  HEATER 40 A fuse
6.  Power MOS FET replacement
Fan: manual LO
8.17
Fan: manual HI
0.6
F
Panel control signal
Instrument cluster
Headlight switch OFF
0
•  Wiring harness: continuity (Climate control unit—instrument cluster: F—1F)
•  Instrument cluster
•  Climate control unit: terminal voltage (D)
Headlight switch ON
2.7
•  Wiring harness: short circuit (Climate control unit—instrument cluster: F—1F)
G
Actuator power
•  Air intake actuator
•  Air mix actuator
•  Airflow mode actuator
IG SW ON
B+
•  Wiring harness: continuity,short circuit (Climate control unit— air intake actuator, air mix actuator, air flow mode actuator: G—A, A, A)
•  Air intake actuator
•  Air mix actuator
•  Airflow mode actuator
IG SW LOCK
1.0 or less
H
GND
Body ground
Under any condition
1.0 or less
•  Wiring harness: continuity (Climate control unit—GND: H—GND)
I
Plus Signal
J
K
A/C
Refrigerant pressure switch
A/C switch ON, fan switch at 1st
1.0 or less
•  Wiring harness: short circuit (Climate control unit—refrigerant pressure switch: K—A)
A/C switch OFF
B+
•  Wiring harness: continuity, short circuit (Climate control unit—refrigerant pressure switch: K—A) (Refrigerant pressure switch—PCM: C—1J )
•  Refrigerant pressure switch
•  PCM: terminal voltage (1J)
L
M
Evaporator temperature sensor input
Evaporator temperature sensor
Compared with temperature detected by evaporator temperature sensor
Refer to graph 1
•  Wiring harness: continuity (Climate control unit—evaporator temperature sensor: M—B, S—A)
•  Wiring harness: short circuit (Climate control unit—evaporator temperature sensor: M—B)
•  Evaporator temperature sensor
N
Rear window defroster operation
Rear window defroster relay
Rear window defroster switch OFF
B+
•  Wiring harness: continuity, short circuit (Climate control unit—rear window defroster relay: N—E)
•  Rear window defroster relay
Rear window defroster switch ON
1.0 or less
O
P
Q
R
S
Sensor GND
Evaporator temperature sensor
Under any condition
1.0 or less
•  Wiring harness: continuity (Climate control unit—GND: S—GND)
T