|
1
|
RECORD SNAPSHOT DATA TO UTILIZE WITH REPEATABILITY VERIFICATION
-
Note
-
• Recording can be facilitated using the screen capture function of the PC.
• Record the snapshot data on the repair order.
|
—
|
Go to the next step.
|
|
2
|
VERIFY DTC REPEATABILITY
-
Note
-
• When clearing the DTC, the snapshot data is also cleared at the same time. Snapshot data is recorded if it is not recorded in Step 1.
• Using the M-MDS, clear the DTC from the EVP control unit.
• Switch the ignition ON (engine off).
• Access the VP_C PID and simulation item VPS_FBK using the M-MDS.
• Verify PID VP_C when the electric vacuum pump is operated by simulation item VPS_FBK.
• Is the VP_C PID 60 A or more?
|
Yes
|
Go to Step 6.
|
|
No
|
Go to the next step.
|
|
3
|
DRIVE VEHICLE THEN VERIFY DTC REPEATABILITY BASED ON SERVICE QUESTIONING RESULTS AND SNAPSHOT DATA
• Switch the ignition ON (engine off).
• Access the VP_C PID and simulation item VPS_FBK using the M-MDS.
• Access the simulation item VPS_FBK using the M-MDS.
• Drive the vehicle based on the service questions content and snapshot data driving conditions.
• Is the VP_C PID 60 A or more, while the vehicle is driven?
|
Yes
|
Go to Step 6.
|
|
No
|
Go to the next step.
|
|
4
|
INSPECT ELECTRIC VACUUM PUMP CIRCUIT
• Switch the ignition OFF.
• Inspect the wiring harness between the following terminals for an open circuit or connector connection malfunction.
-
― Electric vacuum pump terminal B (wiring harness-side)—EVP control unit terminal C (wiring harness-side)
― Electric vacuum pump terminal A (wiring harness-side)—EVP control unit terminal E (wiring harness-side)
• Are inspection results normal?
|
Yes
|
Go to the next step.
|
|
No
|
Repair or replace the malfunctioning part, then go to Step 9.
|
|
5
|
VERIFY DTC REPEATABILITY AND DETERMINE IF MALFUNCTION CAUSE IS EVP CONTROL UNIT
• Using the M-MDS, clear the DTC from the EVP control unit.
• Switch the ignition ON (engine off).
• Using the M-MDS, perform the EVP control unit DTC inspection.
• Is the same Pending DTC present?
|
Yes
|
Replace the EVP control unit, then go to Step 10.
|
|
No
|
DTC troubleshooting completed.
Explain to the customer that there are no malfunctions with the vehicle based on the contents of the servicing.
|
|
6
|
INSPECT ELECTRIC VACUUM PUMP CONNECTOR CONDITION
• Switch the ignition OFF.
• Disconnect the negative battery terminal.
• Disconnect the electric vacuum pump connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is the connector normal?
|
Yes
|
Go to the next step.
|
|
No
|
Repair or replace the connector and/or terminals, then go to Step 9.
|
|
7
|
INSPECT EVP CONTROL UNIT CONNECTOR CONDITION
• Disconnect the EVP control unit connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is the connector normal?
|
Yes
|
Go to the next step.
|
|
No
|
Repair or replace the connector and/or terminals, then go to Step 9.
|
|
8
|
INSPECT ELECTRIC VACUUM PUMP CIRCUIT FOR OPEN CIRCUIT
• Verify that the electric vacuum pump and EVP control unit connectors are disconnected.
• Inspect for continuity as followings:
-
― Electric vacuum pump terminal B (wiring harness-side)—EVP control unit terminal C (wiring harness-side)
― Electric vacuum pump terminal A (wiring harness-side)—EVP control unit terminal E (wiring harness-side)
• Is there continuity?
|
Yes
|
Replace the electric vacuum pump, then go to the next step.
|
|
No
|
Refer to the wiring diagram and verify whether or not there is a common connector in the followings:
• Electric vacuum pump terminal B—EVP control unit terminal C
• Electric vacuum pump terminal A—EVP control unit terminal E
If there is a common connector:
• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
• Repair or replace the malfunctioning part.
If there is no common connector:
• Repair or replace the wiring harness which has an open circuit.
Go to the next step.
|
|
9
|
VERIFY DTC TROUBLESHOOTING COMPLETED
• Using the M-MDS, clear the DTC from the EVP control unit.
• Using the M-MDS, perform the EVP control unit DTC inspection.
• Is the same Pending DTC present?
|
Yes
|
Repeat the inspection from Step1.
If the malfunction recurs, replace the EVP control unit, then go to the next step.
|
|
No
|
Go to the next step.
|
|
10
|
VERIFY NO DTC IS PRESENT
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
|
|
No
|
DTC troubleshooting completed.
|
