DTC B10A3:87 [ADAPTIVE FRONT LIGHTING SYSTEM (AFS) CONTROL MODULE]

id1502b6025900

Description

Communication error with swivel actuator (LH)
Detection condition
•  Adaptive front lighting system (AFS) control module could not receive the signal from the swivel actuator (LH) for 5 s or more with the ignition switched ON (engine off or on).
Fail-safe
•  The swivel actuator (LH) is stopped at the position when the malfunction is determined.
•  The swivel actuator (RH) is moved to the center, or the swivel actuators (LH) and (RH) are moved to the center.
•  Control of the headlight auto leveling system is continued with the headlight leveling actuator positioned −0.6° from where the malfunction is determined.
Possible cause
•  Front combination light (LH) connector or terminal malfunction
•  Adaptive front lighting system (AFS) control module connector or terminal malfunction
•  Short to ground in wiring harness between the following terminals:
―  Adaptive front lighting system (AFS) control module terminal D—Front combination light (LH) terminal K
―  Adaptive front lighting system (AFS) control module terminal F—Front combination light (LH) terminal J
•  Short to power supply in wiring harness between the following terminals:
―  Adaptive front lighting system (AFS) control module terminal D—Front combination light (LH) terminal K
―  Adaptive front lighting system (AFS) control module terminal F—Front combination light (LH) terminal J
•  Open circuit in wiring harness between the following terminals:
―  Adaptive front lighting system (AFS) control module terminal D—Front combination light (LH) terminal K
―  Adaptive front lighting system (AFS) control module terminal F—Front combination light (LH) terminal J
•  Swivel actuator (LH) malfunction
•  Adaptive front lighting system (AFS) control module malfunction

Diagnostic Procedure

Step

Inspection

Action
1
INSPECT FRONT COMBINATION LIGHT (LH) CONNECTOR CONDITION
•  Switch the ignition to off.
•  Disconnect the negative battery terminal.
•  Disconnect the front combination light (LH) connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 7.
2
INSPECT ADAPTIVE FRONT LIGHTING SYSTEM (AFS) CONTROL MODULE CONNECTOR CONDITION
•  Disconnect the adaptive front lighting system (AFS) control module connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 7.
3
INSPECT SWIVEL ACTUATOR (LH) CIRCUIT FOR SHORT TO GROUND
•  Verify that the front combination light (LH) and adaptive front lighting system (AFS) control module connectors are disconnected.
•  Inspect for continuity between the following terminals (wiring harness-side) and body ground:
―  Front combination light (LH) terminal K
―  Front combination light (LH) terminal J
•  Is there continuity?
Yes
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
•  Adaptive front lighting system (AFS) control module terminal D—Front combination light (LH) terminal K
•  Adaptive front lighting system (AFS) control module terminal F—Front combination light (LH) terminal J
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has a short to ground.
Go to Step 7.
No
Go to the next step.
4
INSPECT SWIVEL ACTUATOR (LH) CIRCUIT FOR SHORT TO POWER SUPPLY
•  Verify that the front combination light (LH) and adaptive front lighting system (AFS) control module connectors are disconnected.
•  Disconnect the front combination light (RH) connector.
Note
•  The inspection cannot be performed correctly if the voltage is measured without disconnecting the front combination light (RH) connector because power is supplied to the front combination light (LH) via the front combination light (RH).
•  Connect the negative battery terminal.
•  Switch the ignition ON (engine off or on).
•  Measure the voltage at the following terminals (wiring harness-side):
―  Front combination light (LH) terminal K
―  Front combination light (LH) terminal J
•  Is the voltage 0 V?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
•  Adaptive front lighting system (AFS) control module terminal D—Front combination light (LH) terminal K
•  Adaptive front lighting system (AFS) control module terminal F—Front combination light (LH) terminal J
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has a short to power supply.
Go to Step 7.
5
INSPECT SWIVEL ACTUATOR (LH) CIRCUIT FOR OPEN CIRCUIT
•  Switch the ignition to off.
•  Disconnect the negative battery terminal.
•  Verify that the front combination light (LH) and adaptive front lighting system (AFS) control module connectors are disconnected.
•  Inspect for continuity between the following terminals (wiring harness-side):
―  Adaptive front lighting system (AFS) control module terminal D—Front combination light (LH) terminal K
―  Adaptive front lighting system (AFS) control module terminal F—Front combination light (LH) terminal J
•  Is there continuity?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
•  Adaptive front lighting system (AFS) control module terminal D—Front combination light (LH) terminal K
•  Adaptive front lighting system (AFS) control module terminal F—Front combination light (LH) terminal J
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has an open circuit.
Go to Step 7.
6
VERIFY IF MALFUNCTIONING LOCATION IS SWIVEL ACTUATOR (LH) DEPENDING ON REPEATABILITY
•  Always reconnect all disconnected connectors.
•  Connect the negative battery terminal.
•  Clear the adaptive front lighting system (AFS) control module DTCs using the M-MDS.
•  Switch the ignition ON (engine off or on) and wait for 5 s or more.
•  Retrieve the adaptive front lighting system (AFS) control module DTCs using the M-MDS.
•  Is the same Pending DTC present?
Yes
Replace the front combination light (LH), then go to the next step.
(See FRONT COMBINATION LIGHT REMOVAL/INSTALLATION.)
No
Go to Step 8.
7
VERIFY THAT REPAIRS HAVE BEEN COMPLETED
•  Always reconnect all disconnected connectors.
•  Connect the negative battery terminal.
•  Clear the adaptive front lighting system (AFS) control module DTCs using the M-MDS.
•  Switch the ignition ON (engine off or on) and wait for 5 s or more.
•  Retrieve the adaptive front lighting system (AFS) control module DTCs using the M-MDS.
•  Is the same Pending DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the adaptive front lighting system (AFS) control module, then go to the next step.
No
Go to the next step.
8
VERIFY IF OTHER DTCs DISPLAYED
•  Are any other DTCs displayed?
Yes
Repair the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [ADAPTIVE FRONT LIGHTING SYSTEM (AFS) CONTROL MODULE].)
No
DTC troubleshooting completed.