MAINTENANCE MONITOR OPERATION PROCEDURE

id092000013400

Note
•  The maintenance monitor displays a message when any of the following display conditions is met based on the preset maintenance period.
Display condition
―  Day setting: Remaining days are 15 days or less
―  Distance setting: Remaining distance is 500 km {250 mile}*1 / 1000 km {500 mile}*2
*1 :Connectivity master unit (CMU) is lower than version 59
*2 :CMU is version 59 or higher
•  The instrument cluster displays a message at approx. 5 s intervals according to the following priority order when multiple display conditions are met.
1.  Scheduled maintenance
2.  Tire rotation
3.  Oil inspection/replacement
•  The maintenance monitor setting information recorded in the CMU cannot be written to a new CMU, therefore, the maintenance monitor is set to the initial setting value if the CMU is replaced. Before replacing the CMU, explain to the customer that the maintenance monitor is reset to the initial setting value.
•  After implementing the maintenance, reset the maintenance monitor items that were implemented.

Scheduled Maintenance Setting Procedure

1.  Switch the ignition ON (engine off or on).

2.  Select [Applications] on the center display.

3.  Select [Scheduled Maintenance] on the center display.

4.  Select the following items and change the setting.

Display of center display

Function

Initial setting

Setting contents

Control unit
Setting
Display/non-display of the scheduled maintenance can be set.
Off
On / Off
CMU
Time
Number of days to display of scheduled maintenance can be set.
•  6 months*1
•  12 months
1-36 months
CMU
Distance
Distance to display of scheduled maintenance can be set.
•  10,000 km / 6,250 miles*1
•  20,000 km / 12,500 miles
0-99500 km (0-99750 miles)
CMU
Reset
Maintenance monitor setting can be reset to the initial value.
Back
Back / Reset
CMU

*1  :Australian specs.

Tire Rotation Setting Procedure

1.  Switch the ignition ON (engine off or on).

2.  Select [Applications] on the center display.

3.  Select [Tire Rotation] on the center display.

4.  Select the following items and change the setting.

Display of center display

Function

Initial setting

Setting contents

Control unit
Setting
Display/non-display of the tire rotation can be set.
Off
On / Off
CMU
Distance
Distance to display of tire rotation can be set.
10,000 km / 6,250 miles
0-99500 km (0-99750 miles)
CMU
Reset
Maintenance monitor setting can be reset to the initial value.
Back
Back / Reset
CMU


Oil Change Setting Procedure


Using M-MDS

Caution
•  Do not select "ON" under the following driving conditions.
―  The vehicle is used as a police car, taxi, or for driving instruction.
―  The vehicle is driven under dusty conditions.
―  The vehicle is idled or driven at low speeds for extended periods.
1.  Connect the M-MDS to the DLC-2.
2.  After vehicle identification is completed, select the following from the M-MDS initial screen.
1.  "Powertrain"
2.  "Engine Oil Maintenance Monitor"
3.  "Change setting"
3.  Select "ON*1" or "OFF" from the M-MDS screen.

*1  :When oil inspection/replacement is set to "ON", the engine oil deterioration condition is calculated based on the frequency of engine starts and the distance travelled.

Using center display

"Change setting" is set to "OFF" using M-MDS
1.  Switch the ignition ON (engine off or on).
2.  Select [Applications] on the center display.
3.  Select [Oil Change] on the center display.
4.  Select the following items and change the setting.

Display of center display

Function

Initial setting

Setting contents

Control unit
Setting
Display/non-display of the oil inspection/replacement can be set.
Off
Off / On
CMU
Distance
Distance to display of oil inspection/replacement can be set.
10,000 km / 6,250 miles
0-99500 km (0-99750 miles)
CMU
Reset
Maintenance monitor setting can be reset to the initial value.
Back
Back / Reset
CMU


Oil Deterioration Determination Display Procedure


Using M-MDS

1.  Connect the M-MDS to the DLC-2.
2.  After vehicle identification is completed, select the following from the M-MDS initial screen.
1.  "Powertrain"
2.  "Engine Oil Maintenance Monitor"
3.  Select "Remaining oil life" from the M-MDS screen.


Using center display

1.  Switch the ignition ON (engine off or on).
2.  Select [Applications] on the center display.
3.  Select [Oil Change] on the center display.
4.  Select the following items and change the setting.

Display of center display

Function

Initial setting

Setting contents

Control unit
Oil Life
Oil life to oil inspection/replacement can be displayed.
100%
—
CMU
Reset
Maintenance monitor setting can be reset to the initial value.
Back
Back / Reset
CMU

Note
•  Oil deterioration determination is displayed in the center display only when the "Change setting" for the "Engine Oil Maintenance Monitor" is set to "ON" using the M-MDS.