REAR WHEEL ALIGNMENT [DIMENSIONS]

id098010899000

Specification (Unloaded Condition)

Item

Specification
Total toe-in
Tire [Tolerance ±4 {0.2}]
(mm {in})
3.0 {0.12}
Rim inner [Tolerance ±2.8 {0.11}]
Vehicle equipped with 16 inch wheel: 2.0 {0.079}
Vehicle equipped with 17 inch wheel: 2.1 {0.083}
 
degree
0°17′±10′
Camber
[Tolerance ±1°
Vehicle height: From the end of the rear fender to the center of the wheel (mm {in})
350—358 {13.8—14.0}
-1°23′
359—367 {14.2—14.4}
-1°09′
368—376 {14.5—14.8}
-0°57′
377—385 {14.9—15.1}
-0°46′
386—394 {15.2—15.5}
-0°37′

Note
•  Unloaded condition: Fuel tank is full. Engine coolant and engine oil are at specified level. Jack and tools are in designated position.
•  Difference between the left and right camber angle must be within 1°.

Camber Adjustment

1.  Loosen the installation nut of the lower link adjusting cam bolt.

amxuuw00003382

2.  Rotate the adjusting cam bolt in either direction to adjust the camber.

Specification

Vehicle height*

Camber
350—358 {13.8—14.0}
-1°23′±1°
359—367 {14.2—14.4}
-1°09′±1°
368—376 {14.5—14.8}
-0°57′±1°
377—385 {14.9—15.1}
-0°46′±1°
386—394 {15.2—15.5}
-0°37′±1°

*: Vehicle height: From the end of the rear fender to the center of the wheel (mm {in})

 

Left wheel

Right wheel
Positive direction
Clockwise
Counterclockwise
Negative direction
Counterclockwise
Clockwise

Note
•  Refer to the following figure to adjust the angle of the adjusting cam bolts in single increments.

Lower link adjusting cam bolt adjustment table

Scale

Link movement (mm {in})

Camber change amount (angle)
1
1.8 mm {0.071 in}
-0°35′
2
3.5 mm {0.14 in}
-1°08′
3
4.9 mm {0.19 in}
-1°36′
4
6.1 mm {0.24 in}
-1°58′
5
6.8 mm {0.27 in}
-2°11′
6
7.0 mm {0.28 in}
-2°16′

3.  Tighten the nut.

Tightening torque
85—103 N·m {8.7—10 kgf·m, 63—75 ft·lbf}


Total Toe-in Adjustment

1.  Loosen the installation nut of the lower lateral link adjusting cam bolt.

amxuuw00003383

2.  Rotate the adjusting cam bolt in either direction to adjust the toe-in.

Specification
3.0±2 mm {0.12±0.08in} (0°17′±10′)

 

Left wheel

Right wheel
Toe-in direction
Counterclockwise
Clockwise
Toe-out direction
Clockwise
Counterclockwise

Note
•  Refer to the following figure to adjust the angle of the adjusting cam bolts in single increments.

Lower lateral link adjusting cam bolt adjustment table

Scale

Link movement (mm {in})

Toe change amount (angle)
1
1.8 mm {0.071 in}
0°30′
2
3.5 mm {0.14 in}
0°57′
3
4.9 mm {0.19 in}
1°21′
4
6.1 mm {0.24 in}
1°39′
5
6.8 mm {0.27 in}
1°50′
6
7.0 mm {0.28 in}
1°54′

3.  Tighten the nut.

Tightening torque
85—103 N·m {8.7—10 kgf·m, 63—75 ft·lbf}