ON-BOARD DIAGNOSTIC SYSTEM TEST MODE [PCM (SKYACTIV-D 1.5)]


id0102j6142500


Diagnostic Test Mode

•  To match the OBD regulations, the following diagnostic test modes have been supported.

Diagnostic test mode

Item

Mode 01
Sending diagnostic data (PID data monitor/On-board system readiness test)
Mode 02
Sending freeze frame data
Mode 03
Sending emission-related malfunction code (Diagnostic trouble code: DTC)
Mode 04
Clearing/resetting emission-related malfunction information
Mode 07
Sending continuous monitoring system test results (Pending code)
Mode 08
On-board device control (Simulation test, active command mode)
Mode 09
Request vehicle information


Sending Diagnostic Data (Mode 01)


PID data monitor

•  The PID data monitor items are shown below.

PID data monitor table

—: Not applicable

Full names

Unit

Monitor status since DTCs cleared
Undefined/Not Used
LOAD
%
ECT
°C, °F
MAP
kPa, Bar, psi
Engine speed
rpm
Vehicle speed
km/h, mph
Intake shutter valve
%
OBD requirement according to vehicle design
Distance travelled while check engine light is activated
km, miles
Common rail pressure
kPa, Bar, psi
Distance travelled since DTCs cleared
km, miles
Barometric pressure
kPa, Bar, psi
PCM power supply voltage
V
Relative intake shutter valve position
%
Ambient temperature
°C, °F
Accelerator pedal position No.1
%
Accelerator pedal position No.2
%
Intake shutter valve control desired value
%
Engine oil temperature
°C, °F
MAF sensor
g/s
ECT
°C, °F
IAT sensor No.1
°C, °F
HP-EGR control valve actual opening angle
%
Common rail pressure control system desired value
kPa, Bar, psi
°C, °F
MAP
kPa, Bar, psi
MAP desired value
kPa, Bar, psi
Variable geometry turbocharger desired position
%
Variable geometry turbocharger actual position
%
Exhaust gas pressure
kPa, Bar, psi
Turbocharger turbine revolution
rpm
Boost air temperature
°C, °F
Exhaust gas temperature (No.1)
°C, °F
Exhaust gas temperature (No.2)
°C, °F
Exhaust gas temperature (No.3)
°C, °F
Exhaust gas temperature (No.4)
°C, °F
Diesel particulate filter
kPa, Bar, psi


Sending Freeze Frame Data (Mode 02)

Freeze frame data
•  The freeze frame data consists of data for vehicle and engine control system operation conditions when malfunctions in the engine control system are detected and stored in the PCM.
•  Freeze frame data is stored at the instant the check engine light illuminates, and only a part of the DTC data is stored.
•  For the freeze frame data, if there are several malfunctions in the engine control system, the data for the malfunction which occurred initially is stored. Thereafter, if a misfire or fuel injection control malfunction occurs, data from the misfire or fuel injection control malfunction is written over the initially stored data. However, if the initially stored freeze frame data is a misfire or fuel injection control malfunction, it is not overwritten.
Snapshot data
•  The snapshot data stores the currently detected DTC data.
•  The recording timing for the freeze frame data/snapshot data differs depending on the number of DTC drive cycles.
―  For a DTC with a drive cycle number 1, only the malfunction determination data is recorded.
―  For a DTC with a drive cycle number 2, both the malfunction determination and undetermined data is recorded.

Freeze frame data table

—: Not applicable

Freeze frame data item

Description

Unit

Corresponding PID data monitor item

LOAD
Engine load
%
LOAD
ECT
Engine coolant temperature
°C, °F
ECT
RPM
Engine speed
RPM
RPM
VS
Vehicle speed
KPH, MPH
VSS
IAT
Intake air temperature No.1
°C, °F
IAT
MAF
Mass airflow
g/sec
MAF
TP
Intake shutter valve position
%
ISV_POS
FRP
Fuel pressure at common rail
KPa {MPa}, mBar {Bar}, psi, in H20
FRP
CLRDIST
Mileage after DTC cleared
km, ft, mi
CLR_DIST
BARO
Barometric pressure
KPa {MPa}, mBar {Bar}, psi, in H20
BARO
VPWR
Module supply voltage
V
VPWR
TP_REL
Intake shutter valve opening angle (relative value)
%
AAT
Ambient air temperature
°C, °F
APP_D
Accelerator pedal position No.1
%
APP1
APP_E
Accelerator pedal position No.2
%
APP2
TAC_PCT
Intake shutter valve control desired value
%
ISV_DSD
FUEL_TYP
Fuel type
EOT
Engine oil temperature
°C, °F
EOT
ECT1
Engine coolant temperature
°C, °F
EGR_A_CMD
HP-EGR control valve desired value
%
HPEGR_DSD
EGR_A_ACT
HP-EGR control valve actual value
%
HPEGR_ACT
EGR_A_ERR
HP-EGR control valve error
%
FRP_A_CMD
Commanded fuel pressure at common rail
KPa {MPa}, mBar {Bar}, psi, in H20
FRP_DSD
FRT_A
Fuel temperature at common rail
°C, °F
FRT
BP_A_CMD
Commanded boost air pressure
KPa {MPa}, mBar {Bar}, psi, in H20
MAP_DSD
BP_A_ACT
Actual measured boost air pressure
KPa {MPa}, mBar {Bar}, psi, in H20
MAP
BP_A_ST
Boost air pressure status
Open Loop/Closed Loop/Fault present
VGT_A_CMD
Turbocharger with variable turbine geometry position desired value
%
VGTURB_DSD
VGT_A_ACT
Turbocharger with variable turbine geometry position actual value
%
VGTURB_ACT
EP_1
Exhaust gas pressure sensor No.1 value
KPa {MPa}, mBar {Bar}, psi, in H20
EXHPRES1
TCA_RPM
Turbocharger with variable turbine geometry turbine speed
RPM
VGTURB_RPM
CACT11
Boost air temperature sensor
°C, °F
CACT11
EGT11
Exhaust gas temperature sensor No.1 value
°C, °F
EXHTEMP1
EGT12
Exhaust gas temperature sensor No.2 value
°C, °F
EXHTEMP2
EGT13
Exhaust gas temperature sensor No.3 value
°C, °F
EXHTEMP3
EGT14
Exhaust gas temperature sensor No.4 value
°C, °F
EXHTEMP4
DPF1_DP
Exhaust gas pressure sensor No.2 value
KPa {MPa}, mBar {Bar}, psi, in H20
EXHPRESS_DIF


Snapshot data table

—: Not applicable

Snapshot data item

Definition

Data read/use method

Unit

Corresponding PID data monitor item

ALTT_V
Generator output voltage
V
ALTT V
APP1
Accelerator pedal position No.1
%
APP1
APP2
Accelerator pedal position No.2
%
APP2
ALT_CUR_DSD
Generator target generated current
A
BATT_RES
Battery internal resistance (estimated)
ohm
BATT_RES
TOTAL_TIME
Total energization time for module
The elapsed time when the start stop unit detected a DTC can be calculated by performing the following procedure.
1.  Verify the PID item TOTAL_TIME of the instrument cluster.
2.  Verify the snapshot data item TOTAL_TIME.
3.  Subtract 2 from 1.
hh:mm:ss
TOTAL_DIST
Total distance
The distance traveled when the start stop unit detected a DTC can be calculated by performing the following procedure.
1.  Verify the odometer value in the instrument cluster.
2.  Verify the snapshot data item TOTAL_DIST.
3.  Subtract 2 from 1.
km, ft, mi
FUELSYS
Fuel system status
OL/CL/OL-Drive/OL-Fault/CL-Fault
LOAD_C
Calculated engine load
%
LOAD
ECT
Engine coolant temperature
°C, °F
ECT
RPM
Engine speed
RPM
RPM
VSS
Vehicle speed
KPH, MPH
VSS
IAT
Intake air temperature No.1
°C, °F
MAF
Mass airflow
g/sec
TP1
Intake shutter valve position
%
ISV_POS
EG_RUN_TIME
Time from engine start
hh:mm:ss
FUEL_PRES
Fuel pressure
KPa {MPa}, mBar {Bar}, psi, in H20
FRP
SEGRP_DSD
Target EGR valve position
%
EVAPCP
Purge solenoid valve controlled value
%
FLI
Fuel level in fuel tank
%
CLR_CNT
Number of warm-up cycle after DTC cleared
CLR_DIST
Mileage after DTC cleared
km, ft, mi
CLR_DIST
FTP
Fuel tank pressure
KPa {MPa}, mBar {Bar}, psi, in H20
BARO
Barometric pressure
KPa {MPa}, mBar {Bar}, psi, in H20
BARO
CATT11_DSD
Estimated catalytic converter temperature
°C, °F
VPWR
Module supply voltage
V
VPWR
EQ_RAT11_DSD
Target equivalence ratio (lambda)
TP_REL
Relative throttle position
%
AAT
Ambient air temperature
°C, °F
TP2
Throttle valve position No.2
%
ETC_DSD
Intake shutter valve control desired value
%
ISV_DSD
FUEL_TYP
Type of fuel currently being utilized by the vehicle
NONE/Gas/METH/ETH/DSL/ELEC
SHRTFT12
Short term fuel trim (HO2S)
%
LONGFT12
Long term fuel trim (HO2S)
%
FRP#1
Fuel pressure at common rail (absolute)
KPa {MPa}, mBar {Bar}, psi, in H20
APP_R
Relative accelerator pedal position
%
EOT
Engine oil temperature
°C, °F
EOT
FUEL_TIMING
Main fuel injection timing related to top dead center
°(deg)
FUEL_RATE
Percentage of fuel consumption
l/min
TQ_DD
Engine torque requested by driver
%
TQ_ACT
Actual engine torque value
%
MAF_A
MAF sensor value
g/sec
MAF
ECT1_SUP
Engine coolant temperature No.1 support
No/Yes
ECT2_SUP
Engine coolant temperature No.2 support
No/Yes
ECT1
Engine coolant temperature No.1
°C, °F
ECT2
Engine coolant temperature No.2
°C, °F
IAT11
Intake air temperature No.1 value
°C, °F
IAT12
Intake air temperature No.2 value
°C, °F
IAT13
Intake air temperature No.3 value
°C, °F
EGRP
EGR valve position
%
HPEGR_DSD
EGRP_ACT
EGR valve actual opening angle
%
HPEGR_ACT
EGR_ERR
Percentage of abnormal EGR
%
LPEGRP
Low pressure EGR valve position
%
LPEGRP_ACT
Low pressure EGR valve actual opening angle
%
LPEGR_ERR
Percentage of abnormal low pressure side EGR
%
EGRT11
Exhaust gas recirculation temperature
°C, °F
EGRT12
Low pressure side exhaust gas recirculation temperature
°C, °F
TAC_A_CMD
Commanded throttle valve actuator control
%
TP_A_REL
Relative throttle valve position
%
FRP_A_CMD
Commanded fuel pressure at common rail
KPa {MPa}, mBar {Bar}, psi, in H20
FRP_DSD
FRP_A_CMD_S
Presence or absence of target common rail pressure
No/Yes
FRP_A
Fuel pressure at common rail
KPa {MPa}, mBar {Bar}, psi, in H20
FRP_A_S
Presence or absence of actual common rail pressure
No/Yes
FRT
Fuel temperature at common rail
°C, °F
FRT
FT_A_S
Presence or absence of common rail temperature
No/Yes
TCA_CINP
Manifold absolute pressure No.1 value
KPa {MPa}, mBar {Bar}, psi, in H20
TCB_CINP
Manifold absolute pressure No.1 value
KPa {MPa}, mBar {Bar}, psi, in H20
BP_A_CMD
Commanded manifold absolute pressure No.2
KPa {MPa}, mBar {Bar}, psi, in H20
MAP_DSD
BP_A_ACT
Manifold absolute pressure No.2 value
KPa {MPa}, mBar {Bar}, psi, in H20
MAP
BP_A_ST
Manifold absolute pressure No.2 control status
Open Loop/Closed Loop/Fault present
VGT_A_CMD
Turbocharger with variable turbine geometry position desired value
%
VGTURB_DSD
VGT_A_ACT
Turbocharger with variable turbine geometry position actual value
%
VGTURB_ACT
REGVP_DSD
Regulating valve position desired value
%
REGRP
Regulating valve position
%
EP_1
Exhaust gas pressure sensor No.1 value
KPa {MPa}, mBar {Bar}, psi, in H20
EXHPRES1
TCA_RPM
Turbocharger with variable turbine geometry turbine speed
RPM
VGTURB_RPM
CACT11
Boost air temperature sensor No.1 value
°C, °F
CACT11
EXHTEMP1
Exhaust gas temperature sensor No.1 value
°C, °F
EXHTEMP1
EXHTEMP2
Exhaust gas temperature sensor No.2 value
°C, °F
EXHTEMP2
EXHTEMP3
Exhaust gas temperature sensor No.3 value
°C, °F
EXHTEMP3
EXHPRESS_DIF
Exhaust gas pressure sensor No.2 value
KPa {MPa}, mBar {Bar}, psi, in H20
EXHPRESS_DIF
NOX_ADS_DESULF
Desulfuration condition of NOx adsorbent
No/Yes
NOX_ADS_REGEN
Regeneration condition of NOx adsorbent
No/Yes
DPF_REGN_TYP
Diesel particulate filter regeneration type
Passive/Active
DPF_REGN_STAT
Diesel particulate filter regeneration condition
No/Yes
DPF_REGEN_PCT
Specified value for performing diesel particulate filter regeneration
%
DPF_REGN_AVGD
Average of drive distance from previous diesel particulate filter regeneration to next diesel particulate filter regeneration
km, ft, mi
DTC
DTC causing snapshot data record


Status Byte for DTC

•  The two digits (two digits after hyphen (-)) after the 7-digit DTC.
am6zzn00002906
•  A code which indicates the pending code, current/past malfunction status, or warning illumination status.
•  Can be read by performing a CMDTC self-test using the Mazda Modular Diagnostic System (M-MDS).
•  For details on the status byte, refer to the explanation on the Mazda Modular Diagnostic System (M-MDS) when reading the DTC.

Sending Emission-related Malfunction Code (DTC) (Mode 03)

•  The DTCs are shown below.

×: Applicable
—: Not applicable

DTC No.

Check engine light

Master warning light

i-stop warning light (amber)

Charging system warning light

Engine oil warning light

Wrench indicator light

Diesel particulate filter indicator light

Condition

Fail-safe function

Drive cycle

Monitor item

Self test type*1

Memory function

B10A2:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Vehicle collision
1
Other
C
×
P0016:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Camshaft position/Crankshaft position correlation problem
×
1
CCM
C, R
×
P0030:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor heater control circuit range/performance problem
×
1
A/F sensor
C
×
P0047:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Regulating solenoid valve control circuit low input
×
1
Turbo system
C, O, R
×
P0048:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Regulating solenoid valve control circuit high input
×
1
Turbo system
C, O, R
×
P0072:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ambient temperature sensor circuit low input
1
Other
C, O, R
×
P0073:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ambient temperature sensor circuit high input
1
Other
C, O, R
×
P007B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Boost air temperature sensor circuit range/performance problem
×
2
Turbo system
C
×
P007C:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Boost air temperature sensor circuit low input
×
1
Turbo system
C, O, R
×
P007D:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Boost air temperature sensor circuit high input
×
1
Turbo system
C, O, R
×
P0087:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Low pressure malfunction in common rail fuel pressure control system
×
1
Fuel system
C
×
P0088:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
High pressure malfunction in common rail fuel pressure control system
×
1
Fuel system
C
×
P0089:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
High pressure malfunction in common rail fuel pressure control system
×
1
Fuel system
C
×
P0093:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel leakage from fuel pressure control system
×
1
Fuel system
C
×
P0096:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.2 circuit range/performance problem
×
2
Fuel system
C
×
P0097:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.2 circuit low input
×
1
Fuel system
C, O, R
×
P0098:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.2 circuit high input
×
1
Fuel system
C, O, R
×
P009B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve control circuit open
×
1
Fuel system
C
×
P009C:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve control circuit low input
×
1
Fuel system
C, R
×
P009D:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve control circuit high input
×
1
Fuel system
C, R
×
P009E:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve malfunction (stuck close)
×
1
Fuel system
C
×
P009F:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve malfunction (stuck on)
×
1
Fuel system
C
×
P0101:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAF sensor circuit range/performance problem
×
1
CCM
C, O
×
P0102:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAF sensor circuit low input
×
1
CCM
C, O, R
×
P0103:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAF sensor circuit high input
×
1
CCM
C, O, R
×
P0106:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAP sensor No.2 circuit range/performance problem
×
1
Turbo system
C
×
P0107:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAP sensor No.2 circuit low input
×
1
Turbo system
C, O, R
×
P0108:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAP sensor No.2 circuit high input
×
1
Turbo system
C, O, R
×
P0111:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.1 circuit range/performance problem
×
2
CCM
C
×
P0112:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.1 circuit low input
×
1
CCM
C, O, R
×
P0113:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.1 circuit high input
×
1
CCM
C, O, R
×
P0116:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
ECT sensor circuit range/performance problem
×
1
CCM
C
×
P0117:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
ECT sensor circuit low input
×
1
CCM
C, O, R
×
P0118:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
ECT sensor circuit high input
×
1
CCM
C, O, R
×
P0122:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve position sensor circuit low input
×
1
CCM
C, O, R
×
P0123:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve position sensor circuit high input
×
1
CCM
C, O, R
×
P0130:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor circuit range/performance problem
×
1
A/F sensor
C, O, R
×
P0131:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor circuit low input
×
1
A/F sensor
C, O, R
×
P0132:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor circuit high input
×
1
A/F sensor
C, O, R
×
P0134:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor circuit no activity detected
×
1
A/F sensor
C
×
P0181:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel temperature sensor circuit range/performance problem
×
2
Fuel system
C
×
P0182:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel temperature sensor circuit low input
×
1
Fuel system
C, O, R
×
P0183:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel temperature sensor circuit high input
×
1
Fuel system
C, O, R
×
P0191:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure sensor circuit range/performance problem
×
1
Fuel system
C
×
P0192:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure sensor circuit low input
×
1
Fuel system
C, O, R
×
P0193:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure sensor circuit high input
×
1
Fuel system
C, O, R
×
P0196:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil temperature sensor circuit range/performance problem
×
2
CCM
C
×
P0197:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil temperature sensor circuit low input
×
1
CCM
C, O, R
×
P0198:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil temperature sensor circuit high input
×
1
CCM
C, O, R
×
P0201:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 circuit open
×
1
Fuel system
C, R
×
P0202:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 circuit open
×
1
Fuel system
C, R
×
P0203:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.3 circuit open
×
1
Fuel system
C, R
×
P0204:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.4 circuit open
×
1
Fuel system
C, R
×
P0219:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Engine overspeed condition
1
Other
C
×
P0234:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Turbocharger overboost condition
2
Turbo system
C
×
P026A:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Charge air cooler efficiency below threshold
×
1
Turbo system
C
×
P0299:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Turbocharger underboost condition
2
Turbo system
C
×
P02EE:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 circuit: shorted to each other
×
1
Fuel system
C, R
×
P02EF:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 circuit: shorted to each other
×
1
Fuel system
C, R
×
P02F0:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.3 circuit: shorted to each other
×
1
Fuel system
C, R
×
P02F1:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.4 circuit: shorted to each other
×
1
Fuel system
C, R
×
P0301:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Cylinder No.1 misfire
×
1
CCM
C
×
P0302:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Cylinder No.2 misfire
×
1
CCM
C
×
P0303:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Cylinder No.3 misfire
×
1
CCM
C
×
P0304:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Cylinder No.4 misfire
×
1
CCM
C
×
P0313:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Misfire detected with low fuel
×
1
Other
C
×
P0336:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
CKP sensor circuit range/performance problem
×
2
CCM
C, R
×
P0337:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
CKP sensor circuit problem
×
1
CCM
C, R
×
P0339:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CKP sensor circuit range/performance problem
×
1
CCM
C
×
P0341:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
CMP sensor circuit range/performance problem
×
2
CCM
C, R
×
P0342:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
CMP sensor circuit problem
×
1
CCM
C, R
×
P0401:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
HP-EGR flow insufficient detected
×
2
EGR system
C
×
P0402:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
HP-EGR flow excessive detected
×
1
EGR system
C
×
P0404:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Circuit malfunction in HP-EGR control valve DC motor control system
×
1
EGR system
C, O, R
×
P0405:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
HP-EGR control valve position sensor circuit low input
×
1
EGR system
C, O, R
×
P0406:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
HP-EGR control valve position sensor circuit high input
×
1
EGR system
C, O, R
×
P0407:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR control valve position sensor circuit low input
×
1
EGR system
C, O, R
×
P0408:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR control valve position sensor circuit high input
×
1
EGR system
C, O, R
×
P0421:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Warm up catalyst system efficiency below threshold
2
Catalyst
C
×
P045B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR control valve control: circuit malfunction
×
1
EGR system
C, O, R
×
P0471:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.1 circuit range/performance problem
×
2
Turbo system
C
×
P0472:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.1 circuit low input
×
1
Turbo system
C, O, R
×
P0473:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.1 circuit high input
×
1
Turbo system
C, O, R
×
P0475:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust shutter valve circuit problem
×
1
EGR system
C, O, R
×
P0476:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust shutter valve circuit range/performance problem
×
1
EGR system
C
×
P0480:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Fan control module control circuit problem
1
Other
C, O
×
P0488:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Duty signal error in HP-EGR control valve control system
×
1
EGR system
C
×
P048D:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust shutter valve position sensor circuit low input
×
1
EGR system
C, O, R
×
P048E:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust shutter valve position sensor circuit high input
×
1
EGR system
C, O, R
×
P049B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR flow insufficient detected
×
2
EGR system
C
×
P049C:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR flow excessive detected
×
1
EGR system
C
×
P0500:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
VSS circuit problem
×
1
CCM
C, O, R
×
P0504:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Brake switch circuit problem
×
2
CCM
C
×
P0522:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil pressure sensor circuit low input
×
1
CCM
C, O, R
×
P0523:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil pressure sensor circuit high input
×
1
CCM
C, O, R
×
P0524:00
ON
OFF
OFF
OFF
ON
OFF
OFF
Engine oil pressure too low
×
1
CCM
C
×
P0532:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Refrigerant pressure sensor circuit low input
×
1
Other
C
×
P0533:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Refrigerant pressure sensor circuit high input
×
1
Other
C
×
P053B:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Blow-by heater relay control circuit low input
1
Other
C, O, R
×
P053C:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Blow-by heater relay control circuit high input
1
Other
C, O, R
×
P0545:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.1 circuit low input
×
1
CCM
C, O, R
×
P0546:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.1 circuit high input
×
1
CCM
C
×
P0555:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Power brake unit vacuum sensor circuit problem
×
1
Other
C, R
×
P055F:00
ON
OFF
OFF
OFF
ON
OFF
OFF
Engine oil pressure control circuit low oil pressure
×
1
CCM
C
×
P057F:00
OFF
ON
Flash
OFF
OFF
OFF
OFF
Power system: Battery deterioration
×
1
Other
C
×
P058A:00
OFF
OFF
Flash
ON*4
OFF
OFF
OFF
Current sensor: Function malfunction
×
1
Other
C
×
P0601:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM memory check sum error
×
1
CCM
C, O, R
×
P0602:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PCM programming error
×
1
CCM
C
×
P0605:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM memory check sum error
×
1
CCM
C
×
P0606:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM processor error
×
1
CCM
C, O, R
×
P0607:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Control module performance problem
×
1
CCM
C, O, R
×
P0610:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PCM vehicle configuration error
×
1
CCM
C
×
P0615:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Starter relay circuit problem
1
Other
C
×
P062A:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Suction control valve circuit problem
×
1
Fuel system
C, R
×
P062B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM internal malfunction
×
1
Fuel system
C, O, R
×
P0642:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply circuit low input
×
1
CCM
C
×
P0643:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply circuit high input
×
1
CCM
C
×
P0646:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
A/C relay circuit low input
1
Other
C
×
P0647:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
A/C relay circuit high input
1
Other
C
×
P0652:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply control circuit low input
×
1
CCM
C
×
P0653:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply control circuit high input
×
1
CCM
C
×
P0670:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow control module control circuit problem
1
CCM
C, O
×
P0671:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow plug No.1 control circuit problem
1
CCM
C, O
×
P0672:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow plug No.2 control circuit problem
1
CCM
C, O
×
P0673:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow plug No.3 control circuit problem
1
CCM
C, O
×
P0674:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow plug No.4 control circuit problem
1
CCM
C, O
×
P0698:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply circuit low input
×
1
CCM
C
×
P0699:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply circuit high input
×
1
CCM
C
×
P06B8:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Internal control module non-volatile RAM error
×
1
CCM
C
×
P06DB:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil solenoid valve circuit low input
×
1
CCM
C, O, R
×
P06DC:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil solenoid valve control circuit high input
×
1
CCM
C, O, R
×
P06DD:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Engine oil pressure switch control circuit high input
1
Other
C
×
P06DE:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Engine oil pressure switch control circuit low input
1
Other
C
×
P0703:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Brake switch input circuit problem
×
2
CCM
C
×
P0704:00*2
ON
OFF
OFF
OFF
OFF
OFF
OFF
CPP switch input circuit problem
×
2
CCM
C
×
P07BE:00*2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Transmission indeterminate failure (failed to neutral)
×
1
Other
C
×
P0850:00*2
ON
OFF
OFF
OFF
OFF
OFF
OFF
Neutral switch No.1 input circuit problem
×
2
CCM
C
×
P0A06:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Electric water pump control circuit low input
1
Other
C, O
×
P0A07:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Electric water pump control circuit low input
1
Other
C, O
×
P0A0F:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Engine failed to restart
×
1
Other
C
×
P0A8D:00
OFF
ON
Flash
OFF
OFF
OFF
OFF
Power supply system circuit low input
×
1
Other
C
×
P0A8F:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Power system: Low input
×
1
Other
C
×
P0A94:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
DC-DC converter: control circuit signal error (Without i-ELOOP)
DC-DC converter (i-ELOOP): control circuit signal error (With i-ELOOP)
×
1
Other
C
×
P0C73:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Electric water pump control: abnormal operation
1
Other
C
×
P1051:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too low cylinder No.1
×
2
Fuel system
C
×
P1052:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too high cylinder No.1
×
2
Fuel system
C
×
P1053:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too low cylinder No.2
×
2
Fuel system
C
×
P1054:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too high cylinder No.2
×
2
Fuel system
C
×
P1055:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too low cylinder No.3
×
2
Fuel system
C
×
P1056:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too high cylinder No.3
×
2
Fuel system
C
×
P1057:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too low cylinder No.4
×
2
Fuel system
C
×
P1058:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too high cylinder No.4
×
2
Fuel system
C
×
P111A:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Engine coolant temperature is high
1
Other
C
×
P1142:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel Restriction Condition
×
2
Other
C
×
P115A:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Lack of remaining fuel (output restriction)
×
1
Other
C
×
P115B:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Lack of remaining fuel (fuel injection pause)
×
1
Other
C
×
P117A:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Record of torque restriction for piston protection
1
Other
C
×
P1200:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injection amount learning not completed
×
1
Other
C
×
P1260:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Immobilizer system problem
1
Other
C
×
P1282:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Common rail control system problem
×
1
Fuel system
C
×
P1284:00
ON
ON
OFF
OFF
OFF
OFF
OFF
Fuel injector carbon deposit burn-off procedure not completed
1
CCM
C
×
P1329:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Common rail pressure higher than desired (engine running)
×
1
Fuel system
C
×
P1336:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
CKP sensor/CMP sensor malfunction
1
CCM
C
×
P1378:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector circuit low input
×
1
Fuel system
C, R
×
P1379:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector circuit high input
×
1
Fuel system
C, R
×
P1589:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve control duty signal error
×
1
CCM
C
×
P1675:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector code not programmed
×
1
Fuel system
C
×
P1676:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector code mistakenly programmed
×
1
Fuel system
C
×
P167B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injection amount learning not completed in fuel injection system
×
1
Other
C
×
P176E:00*2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Clutch stroke sensor/starter interlock switch correlation problem
×
1
Other
C
×
P1905:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Check connector circuit low input
1
Other
C
×
P2002:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Diesel particulate filter function decreased
2
Diesel particulate filter system
C
×
P2032:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.2 circuit low input
×
1
CCM
C, O, R
×
P2033:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.2 circuit high input
×
1
CCM
C
×
P2101:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve control circuit overcurrent
×
1
CCM
C, O, R
×
P2104:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve control system: Idle air control
×
1
CCM
C
×
P2105:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Intake air shutter valve actuator control system malfunction (forced engine shutdown)
1
Other
C
×
P2106:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Throttle Actuator Control System - Forced Limited Power
×
1
Other
C
×
P2118:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve control duty signal error
×
2
CCM
C
×
P2122:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.1 circuit low input
×
1
CCM
C, O, R
×
P2123:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.1 circuit high input
×
1
CCM
C, O, R
×
P2127:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.2 circuit low input
×
1
CCM
C, O, R
×
P2128:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.2 circuit high input
×
1
CCM
C, O, R
×
P2138:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.1/No.2 correlation problem
×
1
CCM
C
×
P213B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR valve control: high duty malfunction
×
1
EGR system
C
×
P2146:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 and No.4 open
×
1
Fuel system
C, R
×
P2147:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 and No.4 circuit low input
×
1
Fuel system
C, R
×
P2148:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 and No.4 circuit high input
×
1
Fuel system
C, R
×
P2149:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 and No.3 circuit open
×
1
Fuel system
C, R
×
P2150:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 and No.3 circuit low input
×
1
Fuel system
C, R
×
P2151:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 and No.3 circuit high input
×
1
Fuel system
C, R
×
P2227:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
BARO sensor circuit range/performance problem
×
1
CCM
C
×
P2228:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
BARO sensor circuit low input
×
1
CCM
C, O, R
×
P2229:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
BARO sensor circuit high input
×
1
CCM
C, O, R
×
P2263:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Turbocharger solenoid valve control circuit range/performance problem
×
2
Turbo system
C
×
P2299:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Accelerator pedal: spring back malfunction
1
Other
C
×
P242C:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.3 circuit low input
×
1
CCM
C, O, R
×
P242D:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.3 circuit high input
×
1
CCM
C
×
P242F:00
ON
OFF
OFF
OFF
OFF
OFF
Flash
Diesel particulate filter excess accumulation (exceeded acceptable amount)
×
1
CCM
C
×
P243C:00
OFF
OFF
OFF
OFF
OFF
OFF
Flash
Abnormal diesel particulate filter regeneration interval short distance
1
Other
C
×
P244A:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.2 range/performance problem
×
1
Diesel particulate filter system
C
×
P2452:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Signal malfunction in exhaust gas pressure sensor No.2
1
Diesel particulate filter system
C
×
P2454:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.2 circuit low input
×
1
Diesel particulate filter system
C, O, R
×
P2455:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.2 circuit high input
×
1
Diesel particulate filter system
C, O, R
×
P2456:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Characteristic malfunction in exhaust gas pressure sensor No.2
×
1
Diesel particulate filter system
C
×
P2458:00
OFF
OFF
OFF
OFF
OFF
OFF
Flash
Diesel particulate filter excess accumulation (mid)
×
1
Other
C
×
P2459:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Abnormal diesel particulate filter regeneration interval short distance*5
1
Other
C
×
P2463:00
ON
OFF
OFF
OFF
OFF
OFF
Flash
Diesel particulate filter excess accumulation (large)
×
1
CCM
C
×
P246C:00
OFF
OFF
OFF
OFF
ON
OFF
OFF
Engine oil dilution, oil pressure decreased
1
Other
C
×
P2470:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.4 circuit low input
×
1
CCM
C, O, R
×
P2471:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.4 circuit high input
×
1
CCM
C
×
P2502:00
OFF
OFF
Flash
ON*4
OFF
OFF
OFF
Generator system: Malfunction in voltage generated by generator
×
1
Other
C
×
P2503:00
OFF
OFF
Flash
ON*4
OFF
OFF
OFF
Generator system: Voltage generated by generator is low
×
1
Other
C
×
P2504:00
OFF
OFF
Flash
ON*4
OFF
OFF
OFF
Generator system: Voltage generated by generator is high
×
1
Other
C
×
P2507:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM battery voltage low input
×
1
CCM
C
×
P250A:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Engine oil level signal: engine oil level sensor malfunction
1
Other
C
×
P250C:00
OFF
ON
OFF
OFF
ON
OFF
OFF
Engine oil level sensor power supply circuit malfunction
1
Other
C
×
P250F:00
OFF
OFF
OFF
OFF
OFF
ON
OFF
Engine oil level signal: engine oil level low
1
Other
C
×
P252F:00
OFF
OFF
OFF
OFF
OFF
ON
OFF
Engine oil level too high
1
Other
C
×
P253F:00
OFF
OFF
OFF
OFF
ON
ON
OFF
Engine oil deteriorated
1
Other
C
×
P2564:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Actuator position sensor circuit low input
×
1
Turbo system
C, R
×
P2565:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Actuator position sensor circuit high input
×
1
Turbo system
C, O, R
×
P2579:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Speed sensor assy. (turbocharger) range/performance problem
×
1
Turbo system
C
×
P2580:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Speed sensor assy. (turbocharger) circuit low input
×
1
Turbo system
C
×
P2581:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Speed sensor assy. (turbocharger) circuit high input
×
1
Turbo system
C
×
P2610:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Instrument cluster internal engine off timer performance problem
×
2
CCM
C
×
P2681:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Circuit malfunction in coolant control valve control system
×
1
CCM
C, O, R
×
P2682:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Coolant control valve position sensor circuit low input
1
CCM
C, O, R
×
P2683:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Coolant control valve position sensor circuit high input
1
CCM
C, O, R
×
P26A3:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Coolant control valve control: high duty malfunction
×
1
CCM
C, O
×
P2A00:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Atmosphere learning malfunction in A/F sensor circuit
×
1
A/F sensor
C
×
U0073:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CAN system communication error (HS CAN)
Other
C, O, R
×
U0074:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CAN system communication error (local CAN between PCM and TCM)
Other
C
×
U0101:00
ON
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error to TCM
×
1
CCM
C
×
U0104:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CAN communication: communication error with radar unit
×
1
Other
C
×
U0106:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LIN communication system: glow plug control module information communication error with PCM
×
1
CCM
C, O
×
U0121:00
ON
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error to DSC HU/CM
×
1
CCM
C
×
U0131:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error to EPS control module
1
Other
C
×
U0140:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error to body control module (BCM)
1
Other
C
×
U0151:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error to SAS control module
1
Other
C
×
U0155:00
ON
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error to instrument cluster
×
1
CCM
C
×
U0214:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error to start stop unit
1
Other
C
×
U0235:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CAN communication: communication error to laser sensor
1
Other
C
×
U0298:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN/LIN communication system: DC-DC converter information communication error with body control module (BCM) (without i-ELOOP)
CAN communication: communication error to DC-DC converter (i-ELOOP) (with i-ELOOP)
×
1
Other
C
×
U0302:00*3
ON
OFF
OFF
OFF
OFF
OFF
OFF
TCM processor error
×
1
CCM
C
×
U0305:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Radar unit error
1
Other
C
×
U0315:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DSC HU/CM error
1
Other
C
×
U0320:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
EPS control module error
1
Other
C
×
U0323:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Instrument cluster error
1
Other
C
×
U0336:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SAS control module error
1
Other
C
×
U0338:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Start stop unit error
1
Other
C
×
U0433:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Abnormal message from laser sensor
×
1
Other
C
×
U0599:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Invalid data received from DC-DC converter
×
1
Other
C
×
U1007:00
OFF
ON
Flash
ON
OFF
OFF
OFF
CAN/LIN communication system: current sensor information communication error with body control module (BCM)
Other
C
×
U1100:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
LIN communication: communication error to engine oil level sensor
1
Other
C
×
U2300:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Global central configuration error
1
Other
C
×
U3000:41
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PCM processor error
1
Other
C
×

*1  :C: CMDTC self test, O: KOEO self test, R: KOER self test
*2  :MTX
*3  :ATX
*4  :Displays a message related to a charge system malfunction in the display. (With center display)
*5  :Glow indicator light flashes

Sending Continuous Monitoring System Test Results (pending code) (Mode 07)

•  These appear when a problem is detected in a monitored system.

1-drive cycle type

•  If any problems are detected in the first drive cycle, pending codes will be stored in the PCM memory, as well as DTCs.
•  After pending codes are stored, if the PCM determines that the system is normal in any future drive cycle, the PCM deletes the pending codes.


2-drive cycle type

•  The code for a failed system is stored in the PCM memory in the first drive cycle. If the PCM determines that the system returned to normal or the problem was mistakenly detected, and deletes the pending code. If the problem is found in the second drive cycle too, the PCM determines that the system has failed, and stores the pending codes, and the DTCs.
•  After pending codes are stored, if the PCM determines that the system is normal in any future drive cycle, the PCM deletes the pending codes.