DTC B10FD:76/B10FE:76

id080200822200

System Malfunction Location

DTC

System Malfunction Location

M-MDS display

B10FD:76

Driver-side side air bag sensor ID mismatch

B10FE:76

Passenger-side side air bag sensor ID mismatch

DTC	System Malfunction Location
B10FD:76	Driver-side side air bag sensor ID mismatch
B10FE:76	Passenger-side side air bag sensor ID mismatch

Detection Condition

Warning

• Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.

• Error in the impact magnitude setting of the sensor is detected due to incorrect assembly of the side air bag sensor.

Possible Causes

• Driver-side side air bag sensor installed with incorrect sensor

• Passenger-side side air bag sensor installed with incorrect sensor

• SAS control module malfunction

Diagnostic Procedure

Step

Inspection

Action

1

VERIFY IF SIDE AIR BAG SENSOR IS ASSEMBLED INCORRECTLY

Warning

•  Handling the component parts improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the service warnings/cautions and the workshop manual before handling the air bag system components.
(See AIR BAG SYSTEM SERVICE WARNINGS.)

(See AIR BAG SYSTEM SERVICE CAUTIONS.)

•  Turn the ignition switch to the LOCK position.

•  Disconnect the negative battery cable and wait 1 min or more.

•  Remove the following parts:

―  Front scuff plate
(See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

―  Rear scuff plate
(See REAR SCUFF PLATE REMOVAL/INSTALLATION.)

―  B-pillar lower trim
(See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)

―  Front seat belt
(See FRONT SEAT BELT REMOVAL/INSTALLATION.)

•  Verify that the driver-side and passenger-side side air bag sensors are installed in the correct position.

•  Is each side air bag sensor installed correctly?

Yes

Go to the next step.

No

Install each side air bag sensor to its correct position, then go to the next step.

2

PERFORM SAS CONTROL MODULE DTC INSPECTION

•  Install the front seat belt.

•  Connect the negative battery cable.

•  Clear the DTC for the SAS control module using the M-MDS.
(See CLEARING DTC.)

•  Perform the DTC inspection for the SAS control module using the M-MDS.
(See DTC DISPLAY.)

•  Are the same DTCs present?

Yes

Replace the SAS control module.

(See SAS CONTROL MODULE REMOVAL/INSTALLATION.)

No

DTC troubleshooting completed.

DTC	System Malfunction Location
M-MDS display	System Malfunction Location
B10FD:76	Driver-side side air bag sensor ID mismatch
B10FE:76	Passenger-side side air bag sensor ID mismatch

Step	Inspection		Action
1	VERIFY IF SIDE AIR BAG SENSOR IS ASSEMBLED INCORRECTLY Warning • Handling the component parts improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the service warnings/cautions and the workshop manual before handling the air bag system components. (See AIR BAG SYSTEM SERVICE WARNINGS.) (See AIR BAG SYSTEM SERVICE CAUTIONS.) • Turn the ignition switch to the LOCK position. • Disconnect the negative battery cable and wait 1 min or more. • Remove the following parts: ― Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.) ― Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION.) ― B-pillar lower trim (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.) ― Front seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION.) • Verify that the driver-side and passenger-side side air bag sensors are installed in the correct position. • Is each side air bag sensor installed correctly?	Yes	Go to the next step.
1		No	Install each side air bag sensor to its correct position, then go to the next step.
2	PERFORM SAS CONTROL MODULE DTC INSPECTION • Install the front seat belt. • Connect the negative battery cable. • Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC.) • Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC DISPLAY.) • Are the same DTCs present?	Yes	Replace the SAS control module. (See SAS CONTROL MODULE REMOVAL/INSTALLATION.)
2		No	DTC troubleshooting completed.