SECURITY LIGHT: 14, DTC: B10D7:81/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]

id0902e5356600

DTC	Security light flashing pattern		14	Instrument cluster cannot read key ID number data normally.
	M-MDS display	Instrument cluster	B10D7:81
		PCM	P1260:00
POSSIBLE CAUSE				•  Transponder (key) malfunction •  If any of the following items are touching or near key head, signal communication between key and vehicle is negatively affected, resulting in engine not starting. ―  Spare keys ac9uuw00001496 ―  Keys for other vehicles equipped with an immobilizer system ―  Any metallic object ―  Any electronic device, or any credit or other card with magnetic strips •  Coil antenna installation malfunction •  Coil antenna malfunction •  Instrument cluster malfunction

Diagnostic Procedure

Step	Inspection		Action
1	VERIFY COIL ANTENNA CORRECTLY INSTALLED •  Verify the installation condition of the coil antenna. •   Is the coil antenna correctly installed? (Is the connector not completely connected?)	Yes	Go to the next step.
		No	Install the coil antenna correctly, then go to the next step. (See COIL ANTENNA REMOVAL/INSTALLATION [KEYLESS ENTRY SYSTEM].)
2	VERIFY WHETHER KEY IS VALID OR NOT •  Using another programmed key, turn the ignition switch to the ON position. •  If there is not another programmed key, program an additional key and turn the ignition key to the ON position using the programmed key. (See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [KEYLESS ENTRY SYSTEM].) •  Clear DTCs using the M-MDS. (See CLEARING DTC [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)].) •  Verify DTCs using the M-MDS. (See DTC INSPECTION [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)].) •  Are DTCs output again? ―  Instrument cluster: B10D7:81 ―  PCM:P1260:00	Yes	Replace the coil antenna, then go to the next step. (See COIL ANTENNA REMOVAL/INSTALLATION [KEYLESS ENTRY SYSTEM].)
		No	•  Dispose of the malfunctioning key. •  Program a new key if necessary. (See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [KEYLESS ENTRY SYSTEM].) •  Go to Step 4.
3	INSPECT INSTRUMENT CLUSTER •  Using another programmed key, turn the ignition switch to the ON position. •  Clear DTCs using the M-MDS. (See CLEARING DTC [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)].) •  Verify DTCs using the M-MDS. (See DTC INSPECTION [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)].) •  Are DTCs output again? ―  Instrument cluster: B10D7:81 ―  PCM:P1260:00	Yes	•  Replace the instrument cluster and program the immobilizer system-related parts. (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.) (See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [KEYLESS ENTRY SYSTEM].) •  Go to the next step.
		No	Go to Step 5.
4	VERIFY AFTER REPAIR •  Clear DTCs using the M-MDS. (See CLEARING DTC [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)].) •  Verify DTCs using the M-MDS. (See DTC INSPECTION [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)].) •  Are DTCs output again? ―  Instrument cluster: B10D7:81 ―  PCM:P1260:00	Yes	Inspect DTC P1260:00. (See DTC P1260:00 [ZJ, ZY].)
		No	Go to the next step.
5	VERIFY THAT NO OTHER DTCs ARE PRESENT •  Verify if other DTCs are displayed. •  Are any other DTCs output?	Yes	Perform the corresponding DTC inspection.
		No	DTC troubleshooting completed.