SNAPSHOT DATA TABLE [BODY CONTROL MODULE (BCM)]

id0902r7084400

Snapshot data item

Unit

Data contents

Corresponding data monitor items

AMB_TEMP

°C

Ambient temperature

AMB_TEMP

APP

%

Accelerator pedal position status

APP

BRK_SW

Not Stepping/Stepping

Brake pedal position status

BRK_SW

ECT

°C

Engine coolant temperature

ECT^*1

ENG_RPM

Rpm

Engine speed status

ENG_RPM^*1

ENG_RUN_TIME

Second

Elapsed time since engine was started

—

F_WASH_CTRL_ALLW

Wash_Allowed/Not_Allowed

•  Wash_Allowed: Use of windshield washer is permitted.

•  Not_Allowed: Use of windshield washer is not permitted.

F_WASH_CTRL_ALLW

F_WASH_SW

Off/On

Windshield washer switch status

F_WASH_SW

F_WIP

OFF/FrontWiper On Lo/FrontWiper On Hi/FrontWiperINT Auto On

Windshield wiper switch status

F_WIP

F_WIP_ANG_SEN_FAIL

Not_Failure/Failure

•  Not_Failure: Position sensor in the windshield wiper motor is normal.

•  Failure: Position sensor in the windshield wiper motor has a malfunction.

F_WIP_ANG_SEN_FAIL

F_WIP_CTRL

F.WiperOff/F.WiperLo/F.WiperHi

•  F.WiperOff: Windshield wipers are not operated.

•  F.WiperLo: Windshield wipers are operated at low speed.

•  F.WiperHi: Windshield wipers are operated at high speed.

F_WIP_CTRL

F_WIP_FET_FAIL

Not_Failure/Failure

•  Not_Failure: FET circuit is normal.

•  Failure: FET circuit has a malfunction.

F_WIP_FET_FAIL

F_WIP_INT_VOL

%

Windshield wiper INT level signal value

F_WIP_INT_VOL

F_WIP_POS

Unknown/Parking_Position/Not_Parking_Position

Windshield wipers position status

F_WIP_POS

F_WIP_REG_FAIL

Not_Failure/Failure

•  Not_Failure: Windshield wiper regulator is normal.

•  Failure: Windshield wiper regulator is not normal.

F_WIP_REG_FAIL

F_WIP_REQ

Off/Stop(ParkingPosition)/F.WiperLo/F.WiperHi/Stop(ServicePosition)/Stop(CurrentPosition)

•  Off: Body control module (BCM) does not operate windshield wipers.

•  Stop(ParkingPosition): Body control module (BCM) operates to the park position.

•  F.WiperLo: Body control module (BCM) operates windshield wipers at low speed.

•  F.WiperHi: Body control module (BCM) operates windshield wipers at high speed.

•  Stop(ServicePosition): Body control module (BCM) operates to the service position.

•  Stop(CurrentPosition): Body control module (BCM) operates to the current position.

F_WIP_REQ

F_WIP_ROT_FAIL

Not_Failure/Failure

•  Not_Failure: Windshield wiper rotation direction is normal.

•  Failure: Windshield wiper rotation direction is not normal.

F_WIP_ROT_FAIL

F_WIP_TEACH_STAT_SUB

No_Sub_Status/Detect_jig_out_of_area/Unusually_Mode_Switch/DataFlash_Failure/FrontWipr_Failure/Not_detect_jig

•  No_Sub_Status: Body control module (BCM) cannotreceive any signal from windshield wiper arm andblade.

•  Detect_jig_out_of_area: Windshield wiper arm andblade movement is detected to be outside of specifiedrange.

•  Unusually_Mode_Switch: Windshield wiper andwasher switch is not normal.

•  DataFlash_Failure: Data is not normal.

•  FrontWipr_Failure: Windshield wipers aremalfunctioning.

F_WIP_TEACH_STAT_SUB

F_WIP_THRM_FAIL

Not_Failure/Failure

•  Not_Failure: Circuit detecting windshield wiper motor temperature is normal.

•  Failure: Circuit detecting windshield wiper motor temperature is not normal.

F_WIP_THRM_FAIL

F_WIP_TIME_FAIL

Not_Failure/Failure

•  Not_Failure: Windshield wiper is operating normally.

•  Failure: Windshield wiper operating speed isextremely slow (when the Windshield wiper isoperating).

F_WIP_TIME_FAIL

F_WIP_VOLT_FAIL

Not_Failure/Failure

•  Not_Failure: Circuit detecting windshield wiper motor voltage is normal.

•  Failure: Circuit detecting windshield wiper motor voltage is normal.

F_WIP_VOLT_FAIL

GLOBAL_REAL_TIME

min

Accumulated total elapsed time since vehicle completion until body control module (BCM) detects a DTC

GLOBAL_REAL_TIME

IG_ON_TIMER

min

Elapsed time since ignition was switched ON (engine off or on)

IG_ON_TIMER

POWER_MODE

OFF/ACC/ON/CRANK

Ignition switch status

POWER_MODE

R_WASH_SW

Off/On

•  Off: Rear wiper and washer switch is not in rear washer position.

•  On: Rear wiper and washer switch is in rear washer position.

R_WASH_SW

R_WIP

Off/RearWiperLo/Not defined/WiperINT

•  Off: Rear wiper and washer switch is in the OFF position.

•  RearWiperLo: Rear wiper and washer switch is in the ON position.

•  Not defined: Rear wiper and washer switch position is not determined.

•  WiperINT: Rear wiper and washer switch is in the INT position.

R_WIP

RLS_AMB_TEMP

°C

Rain sensor ambient temperature

RLS_AMB_TEMP

RLS_FAIL_STAT

Faulty(Faulty)/Initialize/Not within specifications/Normal(sensing)

Auto light sensor condition

RLS_FAIL_STAT

RLS_FWD_LGHT_SEN

OK/NG

•  OK: Normal forward brightness can be detected.

•  NG: Normal forward brightness cannot be detected.

RLS_FWD_LGHT_SEN

RLS_I_ILLMI_MODE

Unknown/Off(day_mode)/On(night_mode)

•  Unknown: Panel light illumination request signal is not determined.

•  Off(day_mode): Panel light illumination request signal is not received.

•  On(night_mode): Panel light illumination request signal is received.

RLS_I_ILLMI_MODE

RLS_LGHT_SEN_FAIL

Normal/Fault

•  Normal: Error signals is not received from the auto light sensor.

•  Fault: Error signals is received from the auto light sensor.

RLS_LGHT_SEN_FAIL

RLS_RAIN_SEN_FAIL

Off/On

•  Off: Error signals is not received from the rain sensor.

•  On: Error signals is received from the rain sensor.

RLS_RAIN_SEN_FAIL

RLS_RELAT_HMDTY

%

Relative humidity

RLS_RELAT_HMDTY

RLS_TEMP_SEN_FAIL

Normal/Fault

•  Normal: Error signals is not received from the temperature sensor (built into humidity sensor).

•  Fault: Error signals is received from the temperature sensor (built into humidity sensor) .

RLS_TEMP_SEN_FAIL

RLS_UP_LGHT_SEN

OK/NG

•  OK: Normal upward brightness can be detected.

•  NG: Normal upward brightness cannot be detected.

RLS_UP_LGHT_SEN

RLS_VOLT_FAIL

Normal/Fault

•  Normal: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is normal.

•  Fault: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not normal.

RLS_VOLT_FAIL

RLS_WINDOW_TEMP

°C

Windshield temperature.

RLS_WINDOW_TEMP

RLS_WIP_REQ

WiperOFF/WiperOff_duringAutoINT/Single Wipe/SpeedLow/SpeedHigh/Failure

•  WiperOFF: Wiper operation signal is not received from rain sensor.

•  WiperOff_duringAutoINT: Error signals is received from the auto light sensor.

•  Single Wipe: Signal to operate wiper once is received from rain sensor.

•  SpeedLow: Signal to operate wiper at low speed is received from rain sensor.

•  SpeedHigh: Signal to operate wiper at high speed is received from rain sensor.

•  Failure: Communication with rain sensor is failed.

RLS_WIP_REQ

SHIFT_POS

Parking/Neutral/Parking/Reverse/Neutral/between 2 position/Forward Drive 1/Forward Drive 2/Forward Drive 3/Forward Drive 4/Forward Drive 5/Forward Drive 6/Forward Drive 7/Forward Drive 8/Invalid

Selector lever position status

—

TIRE_PRES_L/F

kPa

Tire pressure (wheel unit (LF))

TIRE_PRES_L/F

TIRE_PRES_L/R

kPa

Tire pressure (wheel unit (LR))

TIRE_PRES_L/R

TIRE_PRES_R/F

kPa

Tire pressure (wheel unit (RF))

TIRE_PRES_R/F

TIRE_PRES_R/R

kPa

Tire pressure (wheel unit (RR))

TIRE_PRES_R/R

TIRE_TEMP_L/F

°C, °F

Tire temperature (wheel unit (LF))

TIRE_TEMP_L/F

TIRE_TEMP_L/R

°C, °F

Tire temperature (wheel unit (LR))

TIRE_TEMP_L/R

TIRE_TEMP_R/F

°C, °F

Tire temperature (wheel unit (RF))

TIRE_TEMP_R/F

TIRE_TEMP_R/R

°C, °F

Tire temperature (wheel unit (RR))

TIRE_TEMP_R/R

TMTR_LO_VOLT

V

Remote transmitter voltage

—

TOTAL_DIST

km

Accumulated total traveled distance from completion of vehicle until body control module (BCM) detects a DTC

TOTAL_DIST

VPWR_CBCM

V

Body control module (BCM) power supply voltage

VPWR_CBCM

VPWR_LIMP_HOME

V

Voltage at body control module (BCM) terminal 1B (power supply)

VPWR_LIMP_HOME

VSS

km/h

Vehicle speed status

VSS

Snapshot data item	Unit	Data contents	Corresponding data monitor items
AMB_TEMP	°C	Ambient temperature	AMB_TEMP
APP	%	Accelerator pedal position status	APP
BRK_SW	Not Stepping/Stepping	Brake pedal position status	BRK_SW
ECT	°C	Engine coolant temperature	ECT^*1
ENG_RPM	Rpm	Engine speed status	ENG_RPM^*1
ENG_RUN_TIME	Second	Elapsed time since engine was started	—
F_WASH_CTRL_ALLW	Wash_Allowed/Not_Allowed	• Wash_Allowed: Use of windshield washer is permitted. • Not_Allowed: Use of windshield washer is not permitted.	F_WASH_CTRL_ALLW
F_WASH_SW	Off/On	Windshield washer switch status	F_WASH_SW
F_WIP	OFF/FrontWiper On Lo/FrontWiper On Hi/FrontWiperINT Auto On	Windshield wiper switch status	F_WIP
F_WIP_ANG_SEN_FAIL	Not_Failure/Failure	• Not_Failure: Position sensor in the windshield wiper motor is normal. • Failure: Position sensor in the windshield wiper motor has a malfunction.	F_WIP_ANG_SEN_FAIL
F_WIP_CTRL	F.WiperOff/F.WiperLo/F.WiperHi	• F.WiperOff: Windshield wipers are not operated. • F.WiperLo: Windshield wipers are operated at low speed. • F.WiperHi: Windshield wipers are operated at high speed.	F_WIP_CTRL
F_WIP_FET_FAIL	Not_Failure/Failure	• Not_Failure: FET circuit is normal. • Failure: FET circuit has a malfunction.	F_WIP_FET_FAIL
F_WIP_INT_VOL	%	Windshield wiper INT level signal value	F_WIP_INT_VOL
F_WIP_POS	Unknown/Parking_Position/Not_Parking_Position	Windshield wipers position status	F_WIP_POS
F_WIP_REG_FAIL	Not_Failure/Failure	• Not_Failure: Windshield wiper regulator is normal. • Failure: Windshield wiper regulator is not normal.	F_WIP_REG_FAIL
F_WIP_REQ	Off/Stop(ParkingPosition)/F.WiperLo/F.WiperHi/Stop(ServicePosition)/Stop(CurrentPosition)	• Off: Body control module (BCM) does not operate windshield wipers. • Stop(ParkingPosition): Body control module (BCM) operates to the park position. • F.WiperLo: Body control module (BCM) operates windshield wipers at low speed. • F.WiperHi: Body control module (BCM) operates windshield wipers at high speed. • Stop(ServicePosition): Body control module (BCM) operates to the service position. • Stop(CurrentPosition): Body control module (BCM) operates to the current position.	F_WIP_REQ
F_WIP_ROT_FAIL	Not_Failure/Failure	• Not_Failure: Windshield wiper rotation direction is normal. • Failure: Windshield wiper rotation direction is not normal.	F_WIP_ROT_FAIL
F_WIP_TEACH_STAT_SUB	No_Sub_Status/Detect_jig_out_of_area/Unusually_Mode_Switch/DataFlash_Failure/FrontWipr_Failure/Not_detect_jig	• No_Sub_Status: Body control module (BCM) cannotreceive any signal from windshield wiper arm andblade. • Detect_jig_out_of_area: Windshield wiper arm andblade movement is detected to be outside of specifiedrange. • Unusually_Mode_Switch: Windshield wiper andwasher switch is not normal. • DataFlash_Failure: Data is not normal. • FrontWipr_Failure: Windshield wipers aremalfunctioning.	F_WIP_TEACH_STAT_SUB
F_WIP_THRM_FAIL	Not_Failure/Failure	• Not_Failure: Circuit detecting windshield wiper motor temperature is normal. • Failure: Circuit detecting windshield wiper motor temperature is not normal.	F_WIP_THRM_FAIL
F_WIP_TIME_FAIL	Not_Failure/Failure	• Not_Failure: Windshield wiper is operating normally. • Failure: Windshield wiper operating speed isextremely slow (when the Windshield wiper isoperating).	F_WIP_TIME_FAIL
F_WIP_VOLT_FAIL	Not_Failure/Failure	• Not_Failure: Circuit detecting windshield wiper motor voltage is normal. • Failure: Circuit detecting windshield wiper motor voltage is normal.	F_WIP_VOLT_FAIL
GLOBAL_REAL_TIME	min	Accumulated total elapsed time since vehicle completion until body control module (BCM) detects a DTC	GLOBAL_REAL_TIME
IG_ON_TIMER	min	Elapsed time since ignition was switched ON (engine off or on)	IG_ON_TIMER
POWER_MODE	OFF/ACC/ON/CRANK	Ignition switch status	POWER_MODE
R_WASH_SW	Off/On	• Off: Rear wiper and washer switch is not in rear washer position. • On: Rear wiper and washer switch is in rear washer position.	R_WASH_SW
R_WIP	Off/RearWiperLo/Not defined/WiperINT	• Off: Rear wiper and washer switch is in the OFF position. • RearWiperLo: Rear wiper and washer switch is in the ON position. • Not defined: Rear wiper and washer switch position is not determined. • WiperINT: Rear wiper and washer switch is in the INT position.	R_WIP
RLS_AMB_TEMP	°C	Rain sensor ambient temperature	RLS_AMB_TEMP
RLS_FAIL_STAT	Faulty(Faulty)/Initialize/Not within specifications/Normal(sensing)	Auto light sensor condition	RLS_FAIL_STAT
RLS_FWD_LGHT_SEN	OK/NG	• OK: Normal forward brightness can be detected. • NG: Normal forward brightness cannot be detected.	RLS_FWD_LGHT_SEN
RLS_I_ILLMI_MODE	Unknown/Off(day_mode)/On(night_mode)	• Unknown: Panel light illumination request signal is not determined. • Off(day_mode): Panel light illumination request signal is not received. • On(night_mode): Panel light illumination request signal is received.	RLS_I_ILLMI_MODE
RLS_LGHT_SEN_FAIL	Normal/Fault	• Normal: Error signals is not received from the auto light sensor. • Fault: Error signals is received from the auto light sensor.	RLS_LGHT_SEN_FAIL
RLS_RAIN_SEN_FAIL	Off/On	• Off: Error signals is not received from the rain sensor. • On: Error signals is received from the rain sensor.	RLS_RAIN_SEN_FAIL
RLS_RELAT_HMDTY	%	Relative humidity	RLS_RELAT_HMDTY
RLS_TEMP_SEN_FAIL	Normal/Fault	• Normal: Error signals is not received from the temperature sensor (built into humidity sensor). • Fault: Error signals is received from the temperature sensor (built into humidity sensor) .	RLS_TEMP_SEN_FAIL
RLS_UP_LGHT_SEN	OK/NG	• OK: Normal upward brightness can be detected. • NG: Normal upward brightness cannot be detected.	RLS_UP_LGHT_SEN
RLS_VOLT_FAIL	Normal/Fault	• Normal: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is normal. • Fault: Power supply voltage of humidity sensor/solar radiation sensor/auto light sensor/rain sensor is not normal.	RLS_VOLT_FAIL
RLS_WINDOW_TEMP	°C	Windshield temperature.	RLS_WINDOW_TEMP
RLS_WIP_REQ	WiperOFF/WiperOff_duringAutoINT/Single Wipe/SpeedLow/SpeedHigh/Failure	• WiperOFF: Wiper operation signal is not received from rain sensor. • WiperOff_duringAutoINT: Error signals is received from the auto light sensor. • Single Wipe: Signal to operate wiper once is received from rain sensor. • SpeedLow: Signal to operate wiper at low speed is received from rain sensor. • SpeedHigh: Signal to operate wiper at high speed is received from rain sensor. • Failure: Communication with rain sensor is failed.	RLS_WIP_REQ
SHIFT_POS	Parking/Neutral/Parking/Reverse/Neutral/between 2 position/Forward Drive 1/Forward Drive 2/Forward Drive 3/Forward Drive 4/Forward Drive 5/Forward Drive 6/Forward Drive 7/Forward Drive 8/Invalid	Selector lever position status	—
TIRE_PRES_L/F	kPa	Tire pressure (wheel unit (LF))	TIRE_PRES_L/F
TIRE_PRES_L/R	kPa	Tire pressure (wheel unit (LR))	TIRE_PRES_L/R
TIRE_PRES_R/F	kPa	Tire pressure (wheel unit (RF))	TIRE_PRES_R/F
TIRE_PRES_R/R	kPa	Tire pressure (wheel unit (RR))	TIRE_PRES_R/R
TIRE_TEMP_L/F	°C, °F	Tire temperature (wheel unit (LF))	TIRE_TEMP_L/F
TIRE_TEMP_L/R	°C, °F	Tire temperature (wheel unit (LR))	TIRE_TEMP_L/R
TIRE_TEMP_R/F	°C, °F	Tire temperature (wheel unit (RF))	TIRE_TEMP_R/F
TIRE_TEMP_R/R	°C, °F	Tire temperature (wheel unit (RR))	TIRE_TEMP_R/R
TMTR_LO_VOLT	V	Remote transmitter voltage	—
TOTAL_DIST	km	Accumulated total traveled distance from completion of vehicle until body control module (BCM) detects a DTC	TOTAL_DIST
VPWR_CBCM	V	Body control module (BCM) power supply voltage	VPWR_CBCM
VPWR_LIMP_HOME	V	Voltage at body control module (BCM) terminal 1B (power supply)	VPWR_LIMP_HOME
VSS	km/h	Vehicle speed status	VSS

*1 :PCM PID (See PID/DATA MONITOR TABLE [PCM (SKYACTIV-G (E))].) (See PID/DATA MONITOR TABLE [PCM (SKYACTIV-D)].) (See PID/DATA MONITOR TABLE [PCM (SKYACTIV-X)].)