PID/DATA MONITOR TABLE [BODY CONTROL MODULE (BCM) (E)]


id0902r71205s3

PID

Unit/Operation

Data contents

Module control terminal

7GTURN_APPLIED_STAT
Off/On
•  Off: Turn light request signal is not received.
•  On: Turn light request signal is received.
ACC_RLY
Off/On
•  Off: ACC relay drive is off.
•  On: ACC relay drive is on.
AGS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: AGS is not equipped.
•  Node Attached and Communicate correctly: AGS is equipped, communication with AGS is normal.
•  NodeAttached but Not Communicate correctly: AGS is equipped, but communication with AGS is not normal.
AIR_INTAKE_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Air intake actuator is not equipped.
•  Node Attached and Communicate correctly: Air intake actuator is equipped, communication with air intake actuator is normal.
•  NodeAttached but Not Communicate correctly: Air intake actuator is equipped, but communication with air intake actuator is not normal.
ALH_HBC_SW
Note
•  Displays in the M-MDS but it does not operate.
ALH_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Adaptive front lighting system (AFS) control module is not equipped.
•  Node Attached and Communicate correctly: Adaptive front lighting system (AFS) control module is equipped, communication with adaptive front lighting system (AFS) control module is normal.
•  NodeAttached but Not Communicate correctly: Adaptive front lighting system (AFS) control module is equipped, but communication withAdaptive front lighting system (AFS) control module is not normal.
AMB_TEMP
°C
Displays ambient temperature
AMP_CAN_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Audio amplifier is not equipped.
•  Node Attached and Communicate correctly: Audio amplifieris equipped, CAN communication with audio amplifier is normal.
•  NodeAttached but Not Communicate correctly: Audio amplifier is equipped, but CAN communication with audio amplifier is not normal.
AMP_MOST_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Audio amplifier is not equipped.
•  Node Attached and Communicate correctly: Audio amplifieris equipped, MOST communication with audio amplifier is normal.
•  NodeAttached but Not Communicate correctly: Audio amplifier is equipped, but MOST communication with audio amplifier is not normal.
ANTI_THEFT_SYS
OFF/ON
•  OFF: Advanced keyless function is off.
•  ON: Advanced keyless function is on.
APP
%
Accelerator pedal opening angle (relative value) with the fully released status as 0% and fully depressed status as 100%
AT_IND_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Shift position indication is not equipped.
•  Node Attached and Communicate correctly: Shift position indication is equipped, communication with shift position indication is normal.
•  NodeAttached but Not Communicate correctly: Shift position indication is equipped, but communication with shift position indicationis not normal.
AUTO_LGHT_OFF
Off/On
•  Off: TNS (parking lights) or headlight off control by auto light off system is not operated.
•  On: TNS (parking lights) or headlight off control by auto light off system is operated.
BATT_SEN_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
BATT_SOC
Note
•  Displays in the M-MDS but it does not operate.
BBS_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
BECM_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
BGLR_ALRM
NoRequest/RequestControl
Note
•  It is displayed, however, if an accessory part is installed, it cannot be used.
 
BGLR_ALRM_ANS
NoRequest/RequestControl
•  NoRequest: Hazard warning light flashing answer−back signal is not received.
•  RequestControl: Hazard warning light flashing answer−back signal is received.
BGLR_ALRM_REQ
NoRequest/Request
•  NoRequest: Body control module (BCM) does not operate theft-deterrent horn and hazard warning lights on.
•  RequestControl: Body control module (BCM) operates the theft-deterrent horn and hazard warning lights on.
BGLR_BACKUP_SIREN
Off/On
•  Off: Backup siren setting is not turned on.
•  On: Backup siren setting is turned on.
3O
BGLR_CHARGE
Note
•  Displays in the M-MDS but it does not operate.
BGLR_GAIN
Note
•  Displays in the M-MDS but it does not operate.
BGLR_HZRD_REQ
Off/Blink 1 time/Blink 2 times/Blink 3 times
•  Off: Hazard warning lights are not operated to flash.
•  Blink 1 time: Hazard warning lights are operated to flash once.
•  Blink 2 times: Hazard warning lights are operated to flash twice.
•  Blink 3 times: Hazard warning lights are operated to flash three times.
BGLR_IMS
Note
•  Displays in the M-MDS but it does not operate.
BGLR_IS_COMD
Note
•  Displays in the M-MDS but it does not operate.
BGLR_SEN
Off/On
•  Off: Intruder sensor setting is not turned on.
•  On: Intruder sensor setting is turned on.
3O
BGLR_SIREN_COMD
Note
•  Displays in the M-MDS but it does not operate.
BGLR_SIREN_MODE
Note
•  Displays in the M-MDS but it does not operate.
BGLR_STAT
DEAD/INITIAL/PRE-ARMING/ARMING/ARMING STAND BY/ALARM/ALARM STAND BY
•  DEAD: Ignition is in ACC or ON (engine off) and alarm cannot be activated.
•  INITIAL: Ignition is switched OFF and transition to arming stand-by status is possible.
•  PRE-ARMING: Transition period to arming status.
•  ARMING: Alarm can be activated by inputting alarm trigger.
•  ARMING STAND BY: Liftgate is open under arming status.
•  ALARM: Alarm trigger is input and alarm is activated.
•  ALARM STAND BY: After alarm activation finished, standing by for next alarm trigger input.
BGLR_SLEEP_MODE
Note
•  Displays in the M-MDS but it does not operate.
B-ISG_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
BRK_SW
Not Stepping/Stepping
•  Not Stepping: Brake pedal is not depressed.
•  Stepping: Brake pedal is depressed.
BRK_SW_1
Off/On
•  Off: Brake switch (No.1 signal) is off.
•  On: Brake switch (No.1 signal) is on.
C_DOOR_LCK_SW_D
Neutral/Lock/Unlock
•  Neutral: Door lock switch (driver's side) is neither locked nor unlocked.
•  Lock: Door lock switch (driver's side) is in lock.
•  Unlock: Door lock switch (driver's side) is in unlock.
C_DOOR_LCK_SW_P
Neutral/Lock/Unlock
•  Neutral: Door lock switch (passenger's side) is neither locked nor unlocked.
•  Lock: Door lock switch (passenger's side) is in lock.
•  Unlock: Door lock switch (passenger's side) is in unlock.
CBCM_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Body control module (BCM) is not equipped.
•  Node Attached and Communicate correctly: Body control module (BCM) is equipped, communication with body control module (BCM) is normal.
•  NodeAttached but Not Communicate correctly: Body control module (BCM) is equipped, but communication with body control module (BCM) is not normal.
CENTER_DISP_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Center display is not equipped.
•  Node Attached and Communicate correctly:Center display is equipped, communication with center display is normal.
•  NodeAttached but Not Communicate correctly: Center display is equipped, but communication with center display is not normal.
CLTCH_INH_SW
Off/On
•  Off: Starter interlock switch is off.
•  On: Starter interlock switch is on.
CMU_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Connectivity master unit (CMU) is not equipped.
•  Node Attached and Communicate correctly: Connectivity master unit (CMU) is equipped, communication with connectivity master unit (CMU) is normal.
•  NodeAttached but Not Communicate correctly:Connectivity master unit (CMU) is equipped, but communication with connectivity master unit (CMU) is not normal.
COMMANDER_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Commander switch is not equipped.
•  Node Attached and Communicate correctly: Commander switch is equipped, communication with commander switch is normal.
•  NodeAttached but Not Communicate correctly: Commander switch is equipped, but communication with commander switch is not normal.
CRASH_SIG
Off/On
•  Off: Crash signal is not received.
•  On: Crash signalis received.
2J, 2L
Dash-ESU_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Dash-electrical supply unit is not equipped.
•  Node Attached and Communicate correctly: Dash-electrical supply unit is equipped, dash-electrical supply unit is normal.
•  NodeAttached but Not Communicate correctly: Dash-electrical supply unit is equipped, but communication with dash-electrical supply unit is not normal.
DCDC_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
DCDC_PCM_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
DOOR_LCK_ALL
Off/On
•  Off: All door lock signal is not sent from body control module (BCM).
•  On: All door lock signal is sent from body control module (BCM).
2J, 2L
DOOR_LCK_ID_CREATE
Off/On
Displays door lock control ID creation status.
DOOR_SECURITY
Off/On
Displays door lock control security condition.
DOOR_SW_ALL
Close/Open
•  Close: All doors are closed.
•  Open: Any door is open.
DOOR_SW_D
Close/Open
•  Close: Front door (driver's side) is closed.
•  Open: Front door (driver's side) is open.
2J, 2L
DOOR_SW_L/R
Close/Open
•  Close: Rear door (LH) is closed.
•  Open: Rear door (LH) is open.
2J, 2L
DOOR_SW_P
Close/Open
•  Close: Front door (passenger's side) is closed.
•  Open: Front door (passenger's side) is open.
2J, 2L
DOOR_SW_R/R
Close/Open
•  Close: Rear door (RH) is closed.
•  Open: Rear door (RH) is open.
2J, 2L
DOOR_ULCK_ALL
Off/On
•  Off: All door unlock signal is not sent from body control module (BCM).
•  On: All door unlock signal is sent from body control module (BCM).
2J, 2L
DOOR_ULCK_D
Off/On
•  Off: Front door (driver's side) unlock request signal is not sent from body control module (BCM).
•  On: Front door (driver's side) unlock request signal is sent from body control module (BCM).
2J, 2L
Door_ESU_D_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Door-electrical supply unit (driver's side) is not equipped.
•  Node Attached and Communicate correctly: Door-electrical supply unit (driver's side) is equipped, communication with door-electrical supply unit (driver's side) is normal.
•  NodeAttached but Not Communicate correctly: Door-electrical supply unit (driver's side) is equipped, but communication with door-electrical supply unit (driver's side) is not normal.
Door_ESU_P_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Door-electrical supply unit (passenger's side) is not equipped.
•  Node Attached and Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, communication with door-electrical supply unit (passenger's side) is normal.
•  NodeAttached but Not Communicate correctly: Door-electrical supply unit (passenger's side) is equipped, but communication with door-electrical supply unit (passenger's side) is not normal.
DRL
Note
•  Displays in the M-MDS but it does not operate.
DRL_REQ
Off/On
•  Off: Body control module (BCM) does not operate daytime running light (DRL) on.
•  On: Body control module (FBCM) operates the daytime running light (DRL) on.
DSC_PT_BUS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: DSC HU/CM is not equipped.
•  Node Attached and Communicate correctly: DSC HU/CM is equipped, communication via CAN BUS No.2 with DSC HU/CM is normal.
•  NodeAttached but Not Communicate correctly: DSC HU/CM is equipped, but communication via CAN BUS No.2 with DSC HU/CM is not normal.
DSC_VEH_BUS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: DSC HU/CM is not equipped.
•  Node Attached and Communicate correctly: DSC HU/CM is equipped, communication via CAN BUS No.1 with DSC HU/CM is normal.
•  NodeAttached but Not Communicate correctly: DSC HU/CM is equipped, but communication via CAN BUS No.1 with DSC HU/CM is not normal.
DSM_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Position memory control module is not equipped.
•  Node Attached and Communicate correctly: Position memory control module is equipped, communication via CAN BUS No.1 with position memory control module is normal.
•  NodeAttached but Not Communicate correctly: Position memory control module is equipped, but communication via CAN BUS No.1 with position memory control module is not normal.
DVD_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
ENG_RPM_VSPD_RATIO
Rpm/Kph
Displays engine speed
ENG_STARTER_VOLT_1
V
Displays voltage at body control module (BCM) terminal 2T
2T
ENG_STARTER_VOLT_2
V
Displays voltage at body control module (BCM) terminal 2AD
2AD
ENG_STAT
Off/Ready/Cranking/Running/Stalled/Afterrun/Shutdown/Not defined
Displays engine condition
EPS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: EPS control module is not equipped.
•  Node Attached and Communicate correctly: EPS control module is equipped, communication with EPS control module is normal.
•  NodeAttached but Not Communicate correctly: EPS control module is equipped, but communication with EPS control module is not normal.
ESS_HZRD
Note
•  Displays in the M-MDS but it does not operate.
ESU_CAN_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
•  Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, CAN communication with electrical supply unit (ESU) is normal.
•  NodeAttached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but CAN communication with electrical supply unit (ESU) is not normal.
ESU_LIN_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Electrical supply unit (ESU) is not equipped.
•  Node Attached and Communicate correctly: Electrical supply unit (ESU) is equipped, LIN communication with electrical supply unit (ESU) is normal.
•  NodeAttached but Not Communicate correctly: Electrical supply unit (ESU) is equipped, but LIN communication with electrical supply unit (ESU) is not normal.
EXT_T/LGT_REL_SW
Off/On
•  Off: Trunk lid opener switch (exterior) (4SD)/liftgate opener switch (5HB) is not pressed.
•  On: Trunk lid opener switch (exterior) (4SD)/liftgate opener switch (5HB) is pressed.
4J
F_WASH_CTRL_ALLW
Wash_Allowed/Not_Allowed
•  Wash_Allowed: Use of windshield washer is permitted.
•  Not_Allowed: Use of windshield washer is not permitted.
F_WASH_SW
Off/On
•  Off: Windshield washer switch is off.
•  On: Windshield washer switch is on.
F_WIP
OFF/FrontWiper On Lo/FrontWiper On Hi/FrontWiperINT Auto On
•  OFF: Windshield wiper switch is in the OFF position.
•  FrontWiper On Lo: Windshield wiper switch is in the LO position.
•  FrontWiper On Hi: Windshield wiper switch is in the HI position.
•  FrontWiperINT Auto On: Windshield wiper switch is in the INT position.
F_WIP_ANG_SEN_FAIL
Not_Failure/Failure
•  Not_Failure: Position sensor in the windshield wiper motor is normal.
•  Failure: Position sensor in the windshield wiper motor has a malfunction.
F_WIP_CTRL
F.WiperOff/F.WiperLo/F.WiperHi
•  F.WiperOff: Windshield wipers are not operated.
•  F.WiperLo: Windshield wipers are operated at low speed.
•  F.WiperHi: Windshield wipers are operated at high speed.
F_WIP_FET_FAIL
Not_Failure/Failure
•  Not_Failure: FET circuit is normal.
•  Failure: FET circuit has a malfunction.
F_WIP_INT_VOL
%
Displays windshield wiper INT level signal value received
F_WIP_POS
Unknown/Parking_Position/Not_Parking_Position
•  Unknown: Windshield wipers position is not determined.
•  Parking_Position: Windshield wipers in park position.
•  Not_Parking_Position: Windshield wipers in position other than park.
F_WIP_REG_FAIL
Not_Failure/Failure
•  Not_Failure: Windshield wiper regulator is normal.
•  Failure: Windshield wiper regulator is not normal.
F_WIP_REQ
Off/Stop(ParkingPosition)/F.WiperLo/F.WiperHi/Stop(ServicePosition)/Stop(CurrentPosition)
•  Off: Body control module (BCM) does not operate windshield wipers.
•  Stop(ParkingPosition): Body control module (BCM) operates windshield wipers to the park position.
•  F.WiperLo: Body control module (BCM) operates windshield wipers at low speed.
•  F.WiperHi: Body control module (BCM) operates windshield wipers at high speed.
•  Stop(ServicePosition): Body control module (BCM) operates windshield wipers to the service position.
•  Stop(CurrentPosition): Body control module (BCM) operates windshield wipers to the current position.
F_WIP_ROT_FAIL
Not_Failure/Failure
•  Not_Failure: Windshield wiper rotation direction is normal.
•  Failure: Windshield wiper rotation direction is not normal.
F_WIP_TEACH_STAT_SUB
No_Sub_Status/Detect_jig_out_of_area/Unusually_Mode_Switch/DataFlash_Failure/FrontWipr_Failure/Not_detect_jig
•  No_Sub_Status: Body control module (BCM) cannot receive any signal from windshield wiper arm and blade.
•  Detect_jig_out_of_area: Windshield wiper arm and blade movement is detected to be outside of specified range.
•  Unusually_Mode_Switch: Windshield wiper and washer switch is not normal.
•  DataFlash_Failure: Data is not normal.
•  FrontWipr_Failure: Windshield wipers are malfunctioning.
F_WIP_THRM_FAIL
Not_Failure/Failure
•  Not_Failure: Circuit detecting windshield wiper motor temperature is normal.
•  Failure: Circuit detecting windshield wiper motor temperature is not normal.
F_WIP_TIME_FAIL
Not_Failure/Failure
•  Not_Failure: Windshield wiper is operating normally.
•  Failure: Windshield wiper operating speed is extremely slow (when the Windshield wiper is operating).
F_WIP_VOLT_FAIL
Not_Failure/Failure
•  Not_Failure: Circuit detecting windshield wiper motor voltage is normal.
•  Failure: Circuit detecting windshield wiper motor voltage is not normal.
FR_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Front radar sensor is not equipped.
•  Node Attached and Communicate correctly: Front radar sensor is equipped, communication with front radar sensor is normal.
•  NodeAttached but Not Communicate correctly: Front radar sensor is equipped, but communication with front radar sensor is not normal.
FSC_LGHT_REQ
Off/On
•  Off: Headlight HI is turned on.
•  On: Headlight HI is turned off.
FSC_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Forward sensing camera (FSC) is not equipped.
•  Node Attached and Communicate correctly: Forward sensing camera (FSC) is equipped, communication with forward sensing camera (FSC) is normal.
•  NodeAttached but Not Communicate correctly: Forward sensing camera (FSC) is equipped, but communication with forward sensing camera (FSC) is not normal.
FSM_REQ
Off/On
•  Off: TNS (parking lights) signal is not sent from body control module (BCM).
•  On: TNS (parking lights) signal is sent from body control module (BCM).
FSRL_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Front side radar sensor (LH) is not equipped.
•  Node Attached and Communicate correctly: Front side radar sensor (LH) is equipped, communication with front side radar sensor (LH) is normal.
•  NodeAttached but Not Communicate correctly: Front side radar sensor (LH) is equipped, but communication with front side radar sensor (LH) is not normal.
FSRR_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Front side radar sensor (RH) is not equipped.
•  Node Attached and Communicate correctly: Front side radar sensor (RH) is equipped, communication with front side radar sensor (RH) is normal.
•  NodeAttached but Not Communicate correctly: Front side radar sensor (RH) is equipped, but communication with front side radar sensor (RH) is not normal.
FUEL_AMOUNT
L
Displays fuel level detected by the fuel gauge
2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_RES_MAIN
Ohm
Displays fuel gauge sender unit resistance value
2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_RES_SUB
Note
•  Displays in the M-MDS but it does not operate.
FUEL_GAUGE_VOLT_MAIN
V
Displays fuel gauge sender unit voltage value
2A, 2B, 2C, 2D, 2E, 2F, 2G, 2H, 2J, 2L, 3S, 3T, 3U, 3V, 3W, 3X, 4M, 4N, 4Q, 4R
FUEL_GAUGE_VOLT_SUB
Note
•  Displays in the M-MDS but it does not operate.
GLOBAL_REAL_TIME
min
Displays cumulative elapsed time since vehicle completion
GLOWPLUG_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
H/L_CLEAN_RLY
Note
•  Displays in the M-MDS but it does not operate.
H/L_HI
Off/On
•  Off: Headlight HI signal is not sent from body control module (BCM).
•  On: Headlight HI signal is sent from body control module (BCM).
H/L_HI_SW
Off/On
•  Off: Light switch HI signal is not received.
•  On: Light switch HI signal is received.
H/L_LO_REQ
Off/On
•  Off: Body control module (BCM) does not operate the headlight LO off.
•  On:Body control module (BCM) does not operate the headlight LO on.
H/L_LO_SW
Off/On
•  Off: Other than light switch LO position of light switch is received.
•  On: Light switch LO position of light switch is received.
H/L_LVL_CSTMZ
Note
•  Displays in the M-MDS but it does not operate.
H/L_OFF_SW
Off/On
•  Off: Light switch OFF signal is not received.
•  On: Light switch OFF signal is received.
H/L_PASSING_SW
Off/On
•  Off: Light switch FLASH−TO−PASS signal is not received.
•  On: Light switch FLASH−TO−PASS signal is received.
HOOD_SW
Close/Open
•  Close: Hood is closed.
•  Open: Hood is open.
2S
HUD_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Active driving display is not equipped.
•  Node Attached and Communicate correctly: Active driving display is equipped, communication with active driving display is normal.
•  NodeAttached but Not Communicate correctly: Active driving display is equipped, but communication with active driving display is not normal.
HZRD_REQ
NoRequest/RequestControl
•  NoRequest: Body control module (BCM) does not operate the hazard warning light on.
•  RequestControl: Body control module (BCM) operates the hazard warning light on.
HZRD_SW
Off/On/Unknown
•  Off: Hazard warning switch is not pressed.
•  On: Hazard warning switch is pressed.
•  Unknown: Hazard warning switch on/off is not determined.
ICM_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Instrument cluster is not equipped.
•  Node Attached and Communicate correctly: Instrument cluster is equipped, communication with instrument cluster is normal.
•  NodeAttached but Not Communicate correctly: Instrument cluster is equipped, but communication with instrument cluster is not normal.
IG_ON_TIMER
min
Time since engine start
IG1_RLY
Off/On
•  Off: IG1 relay drive is off.
•  On: IG1 relay drive is on.
IMMOBI_IDENTIFY
Note
•  Displays in the M-MDS but it does not operate.
IMMOBI_OPERAT_MODE
Operation Mode 1/Operation Mode 2/Operation Mode 3/Operation Mode 4/Operation Mode 5/Operation Mode 6/Operation Mode 7
Displays immobilizer system operation mode
IMS_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
IND_ASSY_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Indicator unit is not equipped.
•  Node Attached and Communicate correctly: Indicator unit is equipped, communication with indicator unit is normal.
•  NodeAttached but Not Communicate correctly: Indicator unit is equipped, but communication with indicator unit is not normal.
IP-ESU_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Climate control unit is not equipped.
•  Node Attached and Communicate correctly: Climate control unit is equipped, communication with climate control unit is normal.
•  NodeAttached but Not Communicate correctly: Climate control unit is equipped, but communication with climate control unit is not normal.
KEY_ANS_REQ
NoRequest/RequestControl
•  NoRequest: Hazard warning light flashing answer−back signal is not received.
•  RequestControl: Hazard warning light flashing answer−back signal is received.
KEY_BUZZER
Off/On
•  Off: Keyless beeper is not operated to sound.
•  On: Keyless beeper is operated to sound.
2AA, 2AB
KEY_ENA
Disabled/Enabled
•  Disabled: Immobilizer system is disabled.
•  Enabled: Immobilizer system is enabled.
LATCH_IP_SW
Off/On
•  Off: Trunk lid opener switch (interior) is not pressed.
•  On: Trunk lid opener switch (interior) is pressed.
LCML_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Light control module (LH) is not equipped.
•  Node Attached and Communicate correctly: Light control module (LH) is equipped, communication with light control module (LH) is normal.
•  NodeAttached but Not Communicate correctly: Light control module (LH) is equipped, but communication with light control module (LH) is not normal.
LCMR_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Light control module (RH) is not equipped.
•  Node Attached and Communicate correctly: Light control module (RH) is equipped, communication with light control module (RH) is normal.
•  NodeAttached but Not Communicate correctly: Light control module (RH) is equipped, but communication with light control module (RH) is not normal.
LFU_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: LF control unit is not equipped.
•  Node Attached and Communicate correctly: LF control unit is equipped, communication with LF control unit is normal.
•  NodeAttached but Not Communicate correctly: LF control unit is equipped, but communication with LF control unit is not normal.
LLINK_SW_D
Unlock/Neutral/Lock/Failure
•  Unlock: Front door lock−link switch (driver's side) is in unlock.
•  Neutral: Front door lock−link switch (driver's side) is not in lock and unlock.
•  Lock: Front door lock−link switch (driver's side) is in lock.
•  Failure: Front door lock−link switch (driver's side) has a malfunction.
LLINK_SW_P
Unlock/Lock
•  Unlock: Front door lock−link switch (passenger's side) is in unlock.
•  Lock: Front door lock−link switch (passenger's side) is in lock.
LLINK_SW_R
Unlock/Lock
•  Unlock: Rear door lock−link switch (LH), rear door lock−link switch (RH) are in unlock.
•  Lock: Rear door lock−link switch (LH), rear door lock−link switch (RH) are in lock.
4F
LLINK_SW_STAT_R
Off/On
•  Off: Front door lock−link switch (LH) is in unlock.
•  On: Front door lock−link switch (LH) is in lock.
MASTER_KEY
No/Yes
•  No: There is no master key.
•  Yes: There is master key.
MODE_ACTAT_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Airflow mode actuator is not equipped.
•  Node Attached and Communicate correctly: Airflow mode actuator is equipped, communication with airflow mode actuator is normal.
•  NodeAttached but Not Communicate correctly: Airflow mode actuator is equipped, but communication with airflow mode actuator is not normal.
MODE_PS_ACTAT_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
MTTR_TIMER
hour
If the ignition is switched OFF after a specified time has elapsed or the vehicle has been driven for a specified period of time or more while in the fail-safe mode, the ignition will remain switched off and the engine cannot be started. Displays the elapsed time since the engine could no longer be started.
NOX1_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
NOX2_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
OHC_ROOMLAMP_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Front map light is not equipped.
•  Node Attached and Communicate correctly: Front map light is equipped, communication with front map light is normal.
•  NodeAttached but Not Communicate correctly: Front map light is equipped, but communication with front map light is not normal.
OIL_LVL_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Engine oil level sensor is not equipped.
•  Node Attached and Communicate correctly: Engine oil level sensor is equipped, communication with engine oil level sensor is normal.
•  NodeAttached but Not Communicate correctly: Engine oil level sensor is equipped, but communication with engine oil level sensor is not normal.
OMC_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Driver monitoring camera unit is not equipped.
•  Node Attached and Communicate correctly: Driver monitoring camera unit is equipped, communication with driver monitoring camera unit is normal.
•  NodeAttached but Not Communicate correctly: Driver monitoring camera unit is equipped, but communication with driver monitoring camera unit is not normal.
OMM_LGHT_OFF
Off/On
•  Off: Battery discharge suppression signal is not sent from body control module (BCM).
•  On: Battery discharge suppression signal is sent from body control module (BCM).
ONE_TOUCH_TURN
Off/On
•  Off: Turn switch LH signal or the turn switch RH signal is not received.
•  On: Turn switch LH signal or the turn switch RH signal is received.
OUTLET_L1_REQ
Note
•  Displays in the M-MDS but it does not operate.
OUTLET_R1_REQ
Note
•  Displays in the M-MDS but it does not operate.
PARK_RANGE_SW
Off/On
•  Off: NOT P position switch is off.
•  On: NOT P position switch is on.
PCM_PT_BUS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: PCM is not equipped.
•  Node Attached and Communicate correctly: PCM is equipped, communication via CAN BUS No.2 with PCM is normal.
•  NodeAttached but Not Communicate correctly: PCM is equipped, but communication via CAN BUS No.2 with is not normal.
PCM_VEH_BUS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: PCM is not equipped.
•  Node Attached and Communicate correctly: PCM is equipped, communication via CAN BUS No.1 with PCM is normal.
•  NodeAttached but Not Communicate correctly: PCM is equipped, but communication via CAN BUS No.1 with is not normal.
PLG_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
PMS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Position memory control module is not equipped.
•  Node Attached and Communicate correctly: Position memory control module is equipped, communication with position memory control module is normal.
•  NodeAttached but Not Communicate correctly: Position memory control module is equipped, but communication with position memory control module is not normal.
PNC_ALRM_HZRD
NoRequest/RequestControl
•  Off: Hazard warning light flashing request signal is not received.
•  On: Hazard warning light flashing request signal is received.
PNC_ALRM_REQ*5
NoRequest/RequestControl
Note
•  It is displayed, however, if an accessory part is installed, it cannot be used.
POWER_MODE
OFF/ACC/ON/CRANK
•  OFF: Body control module (BCM) controls ignition switch off (lock).
•  ACC: Body control module (BCM) controls ignition switch ACC.
•  ON: Body control module (BCM) controls ignition switch ON (engine off).
•  CRANK: Body control module (BCM) controls cranking at ignition switch ON.
PSM_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Parking assist unit (ultrasonic) is not equipped.
•  Node Attached and Communicate correctly: Parking assist unit (ultrasonic) is equipped, communication with parking assist unit (ultrasonic) is normal.
•  NodeAttached but Not Communicate correctly: Parking assist unit (ultrasonic) is equipped, but communication with parking assist unit (ultrasonic) is not normal.
PTC_HEAT_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
R_FOG_SW_IN
Note
•  Displays in the M-MDS but it does not operate.
R_FOG_SW_OUT
Note
•  Displays in the M-MDS but it does not operate.
R_MIX_ACTAT_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
R_TIMER_MODE
OFF/ON
•  OFF: Intermittent wiper operation of rear wiper is disabled.
•  ON: Intermittent wiper operation of rear wiper is enabled.
R_VENT_ACTAT_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Rear vent actuator is not equipped.
•  Node Attached and Communicate correctly: Rear vent actuator is equipped, communication with rear vent actuator is normal.
•  NodeAttached but Not Communicate correctly: Rear vent actuator is equipped, but communication with rear vent actuator is not normal.
R_WASH_SW
Off/On
•  Off: Rear wiper and washer switch is not in rear washer position.
•  On: Rear wiper and washer switch is in rear washer position.
R_WIP
Off/RearWiperLo/Not defined/WiperINT
•  Off: Rear wiper and washer switch is in the OFF position.
•  RearWiperLo: Rear wiper and washer switch is in the ON position.
•  Not defined: Rear wiper and washer switch position is not determined.
•  WiperINT: Rear wiper and washer switch is in the INT position.
R_WIP_CTRL
Deactivate/Activate/Fail(Circuit Short to Ground)/Fail(Circuit Open)/Fail(Circuit Short to Battery)
Rear wiper operation condition input signal from electrical supply unit (ESU)
•  Deactivate: Rear wiper is not operated.
•  Activate: Rear wiper is operated.
•  Fail(Circuit Short to Ground): Short to ground circuit malfunction is received from rear wiper.
•  Fail(Circuit Open): Open circuit malfunction is received from rear wiper.
•  Fail(Circuit Short to Battery): Short to battery circuit malfunction is received from rear wiper.
R_WIP_POS
Unknown/Parking_Position/Not_Parking_Position/AS_SW_Failure
•  Unknown: Rear wiper position is not determined.
•  Parking_Position: Rear wiper in park position.
•  Not_Parking_Position: Rear wiper in position other than park.
•  AS_SW_Failure: Autostop switch has a malfunction.
R_WIP_REQ
Off/Rear Wiper Low On/Stop
•  Off: Body control module (BCM) does not operate rear wiper.
•  Rear Wiper Low On: Body control module (BCM) operates rear wiper.
•  Stop: Body control module (BCM) operates rear wiper to the park position.
R_WIP_STALL_STAT
OK/Stall
•  OK: Rear wiper motor is nomal.
•  Stall: Rear wiper motor is stalled.
RCM_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: SAS control module is not equipped.
•  Node Attached and Communicate correctly: SAS control module is equipped, communication with SAS control module is normal.
•  NodeAttached but Not Communicate correctly: SAS control module is equipped, but communication with SAS control module is not normal.
REGEN_NETWORK
Note
•  Displays in the M-MDS but it does not operate.
RES
Off/On
Note
•  It is displayed, however, if an accessory part is installed, it cannot be used.
RES_HZRD_ANS
NoRequest/RequestControl
Note
•  It is displayed, however, if an accessory part is installed, it cannot be used.
RF_TMTR
FALSE/TRUE
•  FALSE: Remote transmitter ID information is not programmed in LF control unit.
•  TRUE: Remote transmitter ID information is programmed in LF control unit.
RLS_AMB_TEMP
°C
Displays rain sensor ambient temperature.
RLS_AUTO_LGHT_REQ
TNSOff/Head_Off/TNSOn/HeadOff/TNSOn/HeadOn
Illumination request by receiving TNS or headlight illumination request signal.
•  TNSOff/Head_Off: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
•  TNSOn/HeadOff:Body control module (BCM) operates the TNS (parking lights) on.
•  TNSOn/HeadOn: Body control module (BCM) operates the TNS (parking lights) and headlight on.
RLS_CTRL
OFF/TNS Only ON/Low and TNS/Unknown
Illumination request by receiving auto light signal, TNS or headlight illumination request signal.
•  OFF: Body control module (BCM) does not operate the TNS (parking lights) and headlight on.
•  TNS Only ON:Body control module (BCM) operates the TNS (parking lights) on.
•  Low and TNS: Body control module (BCM) operates the TNS (parking lights) and headlight on.
•  Unknown: TNS (parking lights) condition is not detected.
RLS_FAIL
Normal/Fault
•  Normal: Error signals is not received from the auto light sensor.
•  Fault: Error signals is received from the auto light sensor.
RLS_FAIL_STAT
Faulty(Faulty)/Initialize/Not within specifications/Normal(sensing)
Displays auto light sensor condition input signal
RLS_FWD_LGHT_SEN
OK/NG
•  OK: Normal forward brightness can be detected.
•  NG: Normal forward brightness cannot be detected.
RLS_I_ILLMI_MODE
Unknown/Off(day_mode)/On(night_mode)
•  Unknown: Panel light illumination request signal is not determined.
•  Off(day_mode): Panel light illumination request signal is not received.
•  On(night_mode): Panel light illumination request signal is received.
RLS_LGHT_SEN_FAIL
Normal/Fault
•  Normal: Error signals is not received from the auto light sensor.
•  Fault: Error signals is received from the auto light sensor.
RLS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Humidity sensor /solar radiation sensor /auto light sensor /rain sensor is not equipped.
•  Node Attached and Communicate correctly: Humidity sensor /solar radiation sensor /auto light sensor /rain sensor is equipped, communication with humidity sensor /solar radiation sensor /auto light sensor /rain sensor is normal.
•  NodeAttached but Not Communicate correctly: Humidity sensor /solar radiation sensor /auto light sensor /rain sensor is equipped, but communication with humidity sensor /solar radiation sensor /auto light sensor /rain sensor is not normal.
RLS_RAIN_SEN_FAIL
Off/On
•  Off: Error signals is not received from the rain sensor.
•  On: Error signals is received from the rain sensor.
RLS_RELAT_HMDTY
%
Displays relative humidity.
RLS_STAT
Off/TNS On requested/TNS/Headlight On requested/TNS/Headlight On requested
•  Off: TNS (parking lights) and headlight illumination request signal is not received.
•  TNS On requested: TNS (parking lights) illumination request signal is received.
•  TNS/Headlight On requested: TNS (parking lights) and headlight illumination request signal is received.
•  TNS/Headlight On requested: TNS (parking lights) and headlight illumination request signal is received.
RLS_TEMP_SEN_FAIL
Normal/Fault
•  Normal: Error signals is not received from the temperature sensor (built into humidity sensor).
•  Fault: Error signals is received from the temperature sensor (built into humidity sensor) .
RLS_UP_LGHT_SEN
OK/NG
•  OK: Normal upward brightness can be detected.
•  NG: Normal upward brightness cannot be detected.
RLS_VOLT_FAIL
Normal/Fault
•  Normal: Power supply voltage of humidity sensor /solar radiation sensor /auto light sensor /rain sensor is normal.
•  Fault: Power supply voltage of humidity sensor /solar radiation sensor /auto light sensor /rain sensor is not normal.
RLS_WINDOW_TEMP
°C
Displays windshield temperature.
RLS_WIP_REQ
WiperOFF/WiperOff_duringAutoINT/Single Wipe/SpeedLow/SpeedHigh/Failure
•  WiperOFF: Wiper operation signal is not received from rain sensor.
•  WiperOff_duringAutoINT: Error signals is received from the rain sensor.
•  Single Wipe: Signal to operate wiper once is received from rain sensor.
•  SpeedLow: Signal to operate wiper at low speed is received from rain sensor.
•  SpeedHigh: Signal to operate wiper at high speed is received from rain sensor.
•  Failure: Communication with rain sensor is failed.
RSRL_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Rear side radar sensor (LH) is not equipped.
•  Node Attached and Communicate correctly: Rear side radar sensor (LH) is equipped, communication with rear side radar sensor (LH) is normal.
•  NodeAttached but Not Communicate correctly: Rear side radar sensor (LH) is equipped, but communication with rear side radar sensor (LH) is not normal.
S_BELT_LED_OFF_C/R
Off/On
•  Off: Rear seat belt (center) warning light is not illuminated.
•  On: Rear seat belt (center) warning light is illuminated.
S_BELT_LED_OFF_L/R
Off/On
•  Off: Rear seat belt (LH) warning light is not illuminated.
•  On: Rear seat belt (LH) warning light is illuminated.
S_BELT_LED_OFF_R/R
Off/On
•  Off: Rear seat belt (RH) warning light is not illuminated.
•  On: Rear seat belt (RH) warning light is illuminated.
S_BELT_LED_ON_C/R
Off/On
•  Off: Rear seat belt (center) warning light is not illuminated.
•  On: Rear seat belt (center) warning light is illuminated.
S_BELT_LED_ON_L/R
Off/On
•  Off: Rear seat belt (LH) warning light is not illuminated.
•  On: Rear seat belt (LH) warning light is illuminated.
S_BELT_LED_ON_R/R
Off/On
•  Off: Rear seat belt (RH) warning light is not illuminated.
•  On: Rear seat belt (RH) warning light is illuminated.
S_BELT_LED_P
Off/On
•  Off: Passenger seat belt warning light is not illuminated.
•  On: Passenger seat belt warning light is illuminated.
S_BELT_STAT
Vaild/Unknown
•  Vaild: All rear seat belt warning light signals are normal.
•  Unknown: There is a rear seat belt warning light signal error.
S_BELT_STAT_C/3RD
Note
•  Displays in the M-MDS but it does not operate.
S_BELT_STAT_C/R
RearCenter belt not used (Close)/RearCenter belt used (Open)
•  RearCenter belt not used(Close):Rear center seat belt is not fastened.
•  RearCenter belt used(Open): Rear center seat belt is fastened.
S_BELT_STAT_L/3RD
Note
•  Displays in the M-MDS but it does not operate.
S_BELT_STAT_L/R
RearLeft belt not used(Close)/RearLeft belt used(Open)
•  RearLeft belt not used(Close): Rear left seat belt is not fastened.
•  RearLeft belt used(Open): Rear left seat belt is fastened.
S_BELT_STAT_R/3RD
Note
•  Displays in the M-MDS but it does not operate.
S_BELT_STAT_R/R
RearRight belt not used(Close)/RearRight belt not used(Open)
•  RearRight belt not used(Close): Rear right seat belt is not fastened.
•  RearRight belt used(Open): Rear right seat belt is fastened.
S_BELT_WRNG_D
driver belt not used/driver belt used/fault(hole IC switch)/resrve(mech switch)
•  driver belt not used:Driver seat belt is not fastened.
•  driver belt used: Driver seat belt is fastened.
•  fault(hole IC switch)/resrve(mech switch): Driver seat belt has a malfunction.
S_BELT_WRNG_P
driver belt not used/driver belt used/fault(hole IC switch)/resrve(mech switch)
•  driver belt not used: Passenger seat belt is not fastened.
•  driver belt used: Passenger seat belt is fastened.
•  fault(hole IC switch)/resrve(mech switch): Passenger seat belt has a malfunction.
SAS_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Steering angle sensor is not equipped.
•  Node Attached and Communicate correctly: Steering angle sensor is equipped, communication with steering angle sensor is normal.
•  NodeAttached but Not Communicate correctly: Steering angle sensor is equipped, but communication with steering angle sensor is not normal.
SCR_HZRD_REQ
Note
•  Displays in the M-MDS but it does not operate.
SEAT_LETER_ILLMI
Off/On
•  Off: Passenger air bag deactivation (PAD) lettering illumination is not illuminated.
•  On: Passenger air bag deactivation (PAD) lettering illumination is illuminated.
SEAT_OCS_C/R
Note
•  Displays in the M-MDS but it does not operate.
SEAT_OCS_L/R
Note
•  Displays in the M-MDS but it does not operate.
SEAT_OCS_R/R
Note
•  Displays in the M-MDS but it does not operate.
SEAT_OCS_STAT
Note
•  Displays in the M-MDS but it does not operate.
SHIFT
between 2 positions/P/R/N/D/S(2)/L(1)
•  between 2 positions: Selector lever is between two positions.
•  P: Selector lever is in P position.
•  R: Selector lever is in R position.
•  N: Selector lever is in N position.
•  D: Selector lever is in D position.
•  S(2): Selector lever is in D position 2nd gear.
•  L(1): Selector lever is in D position 1st gear.
SLAM_LCK
Off/On
•  On: With all of the following conditions met, lock knob on door equipped with door lock-link switch is locked and all doors are closed.
―  Ignition is switched OFF
―  Any door is open
•  Off: Conditions other than above
SPARE_KEY_STAT
Off/On
•  Off: There is no spare key.
•  On: There is spare key.
SSB_1
Off/On
•  Off: Push button start switch 1 is off.
•  On: Push button start switch 1 is on.
SSB_2
Off/On
•  Off: Push button start switch 2 is off.
•  On: Push button start switch 2 is on.
SSB_AMBER_REQ
Off/On
•  Off: Push button start indicator light (amber) is turned off.
•  On: Push button start indicator light (amber) is illuminated.
SSB_GREEN_REQ
Off/On
•  Off: Push button start indicator light (green) is turned off.
•  On: Push button start indicator light (green) is illuminated.
SSB_ILLMI_REQ
Off/On
•  Off: START/STOP/ENGINE indicator light is turned off.
•  On: START/STOP/ENGINE indicator light is illuminated.
SSU_RES_NUM
0/1/2/3
Note
•  It is displayed, however, if an accessory part is installed, it cannot be used.
SSU_RES_STAT
Disable/Enable
Note
•  It is displayed, however, if an accessory part is installed, it cannot be used.
STR_ANG
° (deg)
Displays steering angle signal (absolute angle)
•  Steering wheel in neutral position: Near 0 degrees
•  Steering wheel turned to left: Changes from 0 degrees to positive
•  Steering wheel turned to right: Changes from 0 degrees to negative
STR_COLM_LCK_CTRL
Note
•  Displays in the M-MDS but it does not operate.
STR_COLM_LCK_GND
Note
•  Displays in the M-MDS but it does not operate.
STR_COLM_LCK_POWER
Note
•  Displays in the M-MDS but it does not operate.
STR_COLM_LCK_STAT
Note
•  Displays in the M-MDS but it does not operate.
STR_HEAT_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Heated steering wheel control unit is not equipped.
•  Node Attached and Communicate correctly: Heated steering wheel control unit is equipped, communication with heated steering wheel control unit is normal.
•  NodeAttached but Not Communicate correctly: Heated steering wheel control unit is equipped, but communication with heated steering wheel control unit is not normal.
SUPER_LCK_ALL
Off/On
•  Off: Double locking function (With double locking) is not operated.
•  On: Double locking function (With double locking) is operated.
2J, 2L
T/LGT_LCK_SW
Off/On
•  Off: Lock request signal is not received.
•  On: Lock request signal is received.
4I
T/LGT_SW
Close/Open
•  Close: Trunk (4SD)/liftgate is closed.
•  Open: Trunk (4SD)/liftgate (5HB) is open.
2J, 2L
T/LGT_ULCK
Off/On
•  Off: Body control module (BCM) does not operate to unlock.
•  On: Body control module (BCM) operates to unlock.
2J, 2L
TCM_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: TCM is not equipped.
•  Node Attached and Communicate correctly: TCM is equipped, communication with TCM is normal.
•  NodeAttached but Not Communicate correctly: TCM is equipped, but communication with TCM is not normal.
TCM_PT2_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: TCM is not equipped.
•  Node Attached and Communicate correctly: TCM is equipped, communication via CAN BUS No.2 with TCM is normal.
•  NodeAttached but Not Communicate correctly: TCM is equipped, but communication via CAN BUS No.2 with TCM is not normal.
TCU_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Telematics communication unit is not equipped.
•  Node Attached and Communicate correctly: Telematics communication unit is equipped, communication with telematics communication unit is normal.
•  NodeAttached but Not Communicate correctly: Telematics communication unit is equipped, but communication with telematics communication unit is not normal.
TEMP_LH_ACTAT_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Driver-side air mix actuator is not equipped.
•  Node Attached and Communicate correctly: Driver-side air mix actuator is equipped, communication with driver-side air mix actuator is normal.
•  NodeAttached but Not Communicate correctly: Driver-side air mix actuator is equipped, but communication with driver-side air mix actuator is not normal.
TEMP_RH_ACTAT_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Passenger-side air mix actuator is not equipped.
•  Node Attached and Communicate correctly: Passenger-side air mix actuator is equipped, communication with passenger-side air mix actuator is normal.
•  NodeAttached but Not Communicate correctly: Passenger-side air mix actuator is equipped, but communication with passenger-side air mix actuator is not normal.
TGT_VERIFY
Error/OK
Displays immobilizer system condition.
TIRE_PRES_L/F
kPa
Displays tire pressure (wheel unit (LF))
TIRE_PRES_L/R
kPa
Displays tire pressure (wheel unit (LR))
TIRE_PRES_R/F
kPa
Displays tire pressure (wheel unit (RF))
TIRE_PRES_R/R
kPa
Displays tire pressure (wheel unit (RR))
TIRE_TEMP_L/F
°C, °F
Displays tire temperature (wheel unit (LF))
TIRE_TEMP_L/R
°C, °F
Displays tire temperature (wheel unit (LR))
TIRE_TEMP_R/F
°C, °F
Displays tire temperature (wheel unit (RF))
TIRE_TEMP_R/R
°C, °F
Displays tire temperature (wheel unit (RR))
TMTR_NUM
0/1/2/3/4/5/6
Displays registration number of the remote transmitter
TNS_REQ
Off/On
•  Off: Body control module (BCM) does not operate the TNS (parking lights) on.
•  On: Body control module (BCM) operates the TNS (parking lights) on.
TNS_SW
Off/On
•  Off: Light switch TNS (parking lights) signal is not received.
•  On: Light switch TNS (parking lights) signal is received.
TOPOLOGY_ID
Displays topological ID
TOTAL_DIST
km
Displays total traveled distance
TPMS_FAIL
Default/Zero Learnt/One Learnt/Two Learnt/Three Learnt/ABS Error/Maximum speed exceeded/Location not determined/Locate data issue
Displays reason why tire position recognition failed.
TPMS_MODE_L/F
Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode
Displays wheel unit (LF) mode
TPMS_MODE_L/R
Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode
Displays wheel unit (LR) mode
TPMS_MODE_R/F
Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode
Displays wheel unit (RF) mode
TPMS_MODE_R/R
Shipping Mode/Drive Mode/Stationary Mode/Interim Mode/Learn Mode/Alert Mode
Displays wheel unit (RR) mode
TUNER_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Remote tuner (RT) is not equipped.
•  Node Attached and Communicate correctly:Remote tuner (RT) is equipped, communication with remote tuner (RT) is normal.
•  NodeAttached but Not Communicate correctly: Remote tuner (RT) is equipped, but communication with remote tuner (RT) is not normal.
TURN_L
Off/On
•  Off: Turn switch LH signal is not sent from body control module (BCM).
•  On: Turn switch LH signal is sent from body control module (BCM).
TURN_L_INTERIOR
Off/On
•  Off: Turn signal (LH) or hazard warning indicator signal is not sent from body control module (BCM).
•  On: Turn signal (LH) or hazard warning indicator signal is sent from body control module (BCM).
TURN_R
Off/On
•  Off: Turn switch RH signal is not sent from body control module (BCM).
•  On: Turn switch RH signal is sent from body control module (BCM).
TURN_R_INTERIOR
Off/On
•  Off: Turn signal (RH) or hazard warning indicator signal is not sent from body control module (BCM).
•  On: Turn signal (RH) or hazard warning indicator signal is sent from body control module (BCM).
TURN_SW
Turn Off/Turn Right ON/Turn Left ON/Unknown
•  Turn Off: Turn switch is in OFF position.
•  Turn Right ON: Turn switch is in RH position.
•  Turn Left ON: Turn switch is in LH position.
•  Unknown: Turn switch position is not determined.
USBHUB_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Auxiliary jack/usb port/sd card slot hub is not equipped.
•  Node Attached and Communicate correctly: Auxiliary jack/usb port/sd card slot hub is equipped, communication with auxiliary jack/usb port/sd card slot hub is normal.
•  NodeAttached but Not Communicate correctly: Auxiliary jack/usb port/sd card slot hub is equipped, but communication with auxiliary jack/usb port/sd card slot hub is not normal.
VCM_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Vehicle control module (VCM) is not equipped.
•  Node Attached and Communicate correctly: Vehicle control module (VCM) is equipped, communication with vehicle control module (VCM) is normal.
•  NodeAttached but Not Communicate correctly: Vehicle control module (VCM) is equipped, but communication with vehicle control module (VCM) is not normal.
VDT_MODE
Note
•  Displays in the M-MDS but it does not operate.
VMC_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: 360°view monitor control module/parking assist unit (optical) is not equipped.
•  Node Attached and Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, communication with 360°view monitor control module/parking assist unit (optical) is normal.
•  NodeAttached but Not Communicate correctly: 360°view monitor control module/parking assist unit (optical) is equipped, but communication with 360°view monitor control module/parking assist unit (optical) is not normal.
VPWR_ACC
V
Displays voltage at body control module (BCM) terminal 2AE (ACC power supply)
2AE
VPWR_CBCM
V
Displays power supply voltage of body control module (BCM)
VPWR_ESCL
V
Displays voltage at body control module (BCM) terminal 4W (power supply)
4W
VPWR_IG
V
Displays voltage at body control module (BCM) terminal 2AF (ignition power supply)
2AF
VPWR_LIMP_HOME
V
Displays voltage at body control module (BCM) terminal 1B (power supply)
1B
VPWR_ROOM
V
Displays voltage at body control module (BCM) terminal 1D (power supply)
1D
WASH_MOTOR_STAT
Off/Washer_Motor_L/Washer_Motor_R
•  Off: Windshield washer motor relay and rear washer motor relay are off.
•  Washer_Motor_L: Windshield washer motor relay is on.
•  Washer_Motor_R: Rear washer motor relay is on.
WIP_NETWORK
Node is not attached on Vehicle/Node Attached and Communicate correctly/NodeAttached but Not Communicate correctly
•  Node is not attached on Vehicle: Windshield wiper motor is not equipped.
•  Node Attached and Communicate correctly: Windshield wiper motor is equipped, communication with windshield wiper motor is normal.
•  NodeAttached but Not Communicate correctly: Windshield wiper motor is equipped, but communication with windshield wiper motor is not normal.