POSITION CANNOT BE PROGRAMMED [POSITION MEMORY SYSTEM]

id0903p5067400

Outline

Description

•  When programming a position, the programming completed sound is not activated.

•  When programming a position, the programming error sound is activated.

Possible cause

•  Position memory switch malfunction

•  Instrument cluster malfunction

•  Notification and warning speaker malfunction

•  Position memory control module malfunction

Diagnostic Procedure

Step

Inspection

Results

Action

1

VERIFY ALL SYSTEM DTCs

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

Go to the next step.

2

INSPECT POSITION MEMORY SWITCH FOR MALFUNCTION

•  Inspect the applicable part.
(See POSITION MEMORY SWITCH INSPECTION.)

•  Is the part normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

(See POSITION MEMORY SWITCH REMOVAL/INSTALLATION.)

3

INSPECT INSTRUMENT CLUSTER FOR MALFUNCTION

•  Inspect the applicable part.
(See INSTRUMENT CLUSTER INSPECTION [(E)].)

•  Is the part normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

(See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)

4

INSPECT NOTIFICATION AND WARNING SPEAKER FOR MALFUNCTION

•  Inspect the applicable part.
(See NOTIFICATION AND WARNING SPEAKER INSPECTION.)

•  Is the part normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

(See NOTIFICATION AND WARNING SPEAKER REMOVAL/INSTALLATION.)

Repair completion verification

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Has the malfunction symptom been eliminated?

Yes

Complete the symptom troubleshooting. (Explain contents of repair to customer)

No

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction is not resolved, replace the position memory control module.
(See POSITION MEMORY CONTROL MODULE REMOVAL/INSTALLATION [(E)].)

Description	• When programming a position, the programming completed sound is not activated. • When programming a position, the programming error sound is activated.
Possible cause	• Position memory switch malfunction • Instrument cluster malfunction • Notification and warning speaker malfunction • Position memory control module malfunction

Step	Inspection	Results	Action
1	VERIFY ALL SYSTEM DTCs • Perform the DTC inspection. (See DTC INSPECTION.) • Are any DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
1		No	Go to the next step.
2	INSPECT POSITION MEMORY SWITCH FOR MALFUNCTION • Inspect the applicable part. (See POSITION MEMORY SWITCH INSPECTION.) • Is the part normal?	Yes	Go to the next step.
2		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See POSITION MEMORY SWITCH REMOVAL/INSTALLATION.)
3	INSPECT INSTRUMENT CLUSTER FOR MALFUNCTION • Inspect the applicable part. (See INSTRUMENT CLUSTER INSPECTION [(E)].) • Is the part normal?	Yes	Go to the next step.
3		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
4	INSPECT NOTIFICATION AND WARNING SPEAKER FOR MALFUNCTION • Inspect the applicable part. (See NOTIFICATION AND WARNING SPEAKER INSPECTION.) • Is the part normal?	Yes	Go to the next step.
4		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See NOTIFICATION AND WARNING SPEAKER REMOVAL/INSTALLATION.)
Repair completion verification	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Has the malfunction symptom been eliminated?	Yes	Complete the symptom troubleshooting. (Explain contents of repair to customer)
Repair completion verification		No	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction is not resolved, replace the position memory control module. (See POSITION MEMORY CONTROL MODULE REMOVAL/INSTALLATION [(E)].)