ON-BOARD DIAGNOSTIC TEST [LF, L5]

id0102c8801000

DTC Reading Procedure

1. Connect the M-MDS to the DLC-2.

am3uuw00003405

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

• When using the IDS (laptop PC)

1. Select “Self Test”.

2. Select “Modules”.

3. Select “PCM”.

• When using the PDS (Pocket PC)

1. Select “Module Tests”.

2. Select “PCM”.

3. Select “Self Test”.

3. Then, select the “Retrieve CMDTCs” and perform procedures according to directions on the M-MDS screen.

4. Verify the DTC according to the directions on the M-MDS screen.

• If any DTCs are displayed, perform troubleshooting according to the corresponding DTC inspection.

5. After completion of repairs, clear all DTCs stored in the PCM, while referring to “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [LF, L5].)

Pending Trouble Code Access Procedure

1. Connect the M-MDS to the DLC-2.

am3uuw00003405

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

• When using the IDS (laptop PC)

1. Select “Self Test”.

2. Select “Modules”.

3. Select “PCM”.

• When using the PDS (Pocket PC)

1. Select “Module Tests”.

2. Select “PCM”.

3. Select “Self Test”.

3. Then, select the “Retrieve CMDTCs” and perform procedures according to directions on the M-MDS screen.

4. Retrieve the pending trouble codes according to the directions on the M-MDS screen.

Freeze Frame PID Data Access Procedure

1. Connect the M-MDS to the DLC-2.

am3uuw00003405

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

• When using the IDS (laptop PC)

1. Select “Self Test”.

2. Select “Modules”.

3. Select “PCM”.

• When using the PDS (Pocket PC)

1. Select “Module Tests”.

2. Select “PCM”.

3. Select “Self Test”.

3. Then, select the “Retrieve CMDTCs” and perform procedures according to directions on the M-MDS screen.

4. Retrieve the freeze frame PID data according to the directions on the M-MDS screen.

Note

• Freeze frame data/snapshot data appears at the top of the help screen when the displayed DTC is selected.

Freeze frame data

• The freeze frame data consists of data for vehicle and engine control system operation conditions when malfunctions in the engine control system are detected and stored in the PCM.

• Freeze frame data is stored at the instant the malfunction indicator lamp illuminates, and only a part of the DTC data is stored.

• For the freeze frame data, if there are several malfunctions in the engine control system, the data for the malfunction which occurred initially is stored. Thereafter, if a misfire or fuel injection control malfunction occurs, data from the misfire or fuel injection control malfunction is written over the initially stored data. However, if the initially stored freeze frame data is a misfire or fuel injection control malfunction, it is not overwritten.

Snapshot data

• The snap shot data stores the currently detected DTC data.

• The recording timing for the freeze frame data/snap shot data differs depending on the number of DTC drive cycles.

― For a DTC with a drive cycle number 1, only the malfunction determination data is recorded.

― For a DTC with a drive cycle number 2, both the malfunction determination and undetermined data is recorded.

Freeze frame data table

Note

• Refer to PID monitor table for confirm the engine control system operation status while the PCM does not store the DTC. (See PCM INSPECTION [LF, L5].)

• Freeze frame data items are not displayed, according to detected DTC.

Freeze frame data item

Unit

Description

Corresponding PID data monitor item

FUELSYS1

Open Loop/Closed Loop/OL-Drive/OL-Fault/CL-Fault

Fuel system status

FUELSYS

LOAD

%

Calculated engine load

—

ECT

°C

Engine coolant temperature

ECT

SFT1

%

Short term fuel trim

SHRTFT1

LFT1

%

Long term fuel trim

LONGFT1

MAP

Pa

Manifold absolute pressure

MAP

RPM

RPM

Engine speed

RPM

VS

KPH

Vehicle speed

VSS

SPARKADV

°

Ignition timing

SPARKADV

IAT

°C

Intake air temperature

IAT

MAF

g/sec

Mass airflow

MAF

TP

%

Throttle valve position No.1

TP1

RUNTM

hh:mm:ss

Time from engine start

—

EGRPCT

%

Target EGR valve position

SEGRP_DSD

EVAPPCT

%

Purge solenoid valve controlled value

EVAPCP

WARMUPS

—

Number of warm-up cycle after DTC cleared

—

CLRDIST

Km

Mileage after DTC cleared

—

CATTEMP11

°C

Estimated catalytic converter temperature

CATT11_DSD

VPWR

V

Module supply voltage

VPWR

ALV

%

Engine load

LOAD

TP_REL

%

Relative throttle position

TP REL

TP_B

%

Throttle valve position No.2

TP2

APP_D

%

Accelerator pedal position No.1

APP1

APP_E

%

Accelerator pedal position No.2

APP2

TAC_PCT

%

Target throttle valve position

ETC_DSD

Freeze frame data item	Unit	Description	Corresponding PID data monitor item
FUELSYS1	Open Loop/Closed Loop/OL-Drive/OL-Fault/CL-Fault	Fuel system status	FUELSYS
LOAD	%	Calculated engine load	—
ECT	°C	Engine coolant temperature	ECT
SFT1	%	Short term fuel trim	SHRTFT1
LFT1	%	Long term fuel trim	LONGFT1
MAP	Pa	Manifold absolute pressure	MAP
RPM	RPM	Engine speed	RPM
VS	KPH	Vehicle speed	VSS
SPARKADV	°	Ignition timing	SPARKADV
IAT	°C	Intake air temperature	IAT
MAF	g/sec	Mass airflow	MAF
TP	%	Throttle valve position No.1	TP1
RUNTM	hh:mm:ss	Time from engine start	—
EGRPCT	%	Target EGR valve position	SEGRP_DSD
EVAPPCT	%	Purge solenoid valve controlled value	EVAPCP
WARMUPS	—	Number of warm-up cycle after DTC cleared	—
CLRDIST	Km	Mileage after DTC cleared	—
CATTEMP11	°C	Estimated catalytic converter temperature	CATT11_DSD
VPWR	V	Module supply voltage	VPWR
ALV	%	Engine load	LOAD
TP_REL	%	Relative throttle position	TP REL
TP_B	%	Throttle valve position No.2	TP2
APP_D	%	Accelerator pedal position No.1	APP1
APP_E	%	Accelerator pedal position No.2	APP2
TAC_PCT	%	Target throttle valve position	ETC_DSD

Snapshot data table

Note

• Refer to PID monitor table for confirm the engine control system operation status while the PCM does not store the DTC. (See PCM INSPECTION [LF, L5].)

• Snapshot data items are not displayed, according to detected DTC.

Snapshot data item

Unit

Definition

Corresponding PID data monitor item

FUELSYS

OL/CL/OL-Drive/OL-Fault/CL-Fault

Fuel system status

FUELSYS

LOAD_C

%

Calculated engine load

—

ECT

°C

Engine coolant temperature

ECT

SHRTFT1

%

Short term fuel trim

SHRTFT1

LONGFT1

%

Long term fuel trim

LONGFT1

MAP

Pa

Manifold absolute pressure

MAP

RPM

RPM

Engine speed

RPM

VSS

KPH

Vehicle speed

VSS

SPARKADV

°

Ignition timing

SPARKADV

IAT

°C

Intake air temperature

IAT

MAF

g/sec

Mass airflow

MAF

TP1

%

Throttle valve position No.1

TP1

EG_RUN_TIME

—

Time from engine start

—

SEGRP_DSD

%

Target EGR valve position

SEGRP DSD

EVAPCP

%

Purge solenoid valve controlled value

EVAPCP

FLI

%

Fuel level in fuel tank

—

CLR_CNT

—

Number of warm-up cycle after DTC cleared

—

CLR_DIST

km

Mileage after DTC cleared

—

FTP

Pa

Fuel tank pressure

—

BARO

Pa

Barometric pressure

—

CATT11_DSD

°C

Estimated catalytic converter temperature

CATT11_DSD

VPWR

V

Module supply voltage

VPWR

LOAD

%

Engine load

LOAD

EQ_RAT11_DSD

—

Target equivalence ratio (lambda)

EQ_RAT11_DSD

TP REL

%

Relative throttle position

TP REL

AAT

°C

Ambient air temperature

—

TP2

%

Throttle valve position No.2

TP2

APP1

%

Accelerator pedal position No.1

APP1

APP2

%

Accelerator pedal position No.2

APP2

ETC_DSD

%

Target throttle valve position

ETC_DSD

Snapshot data item	Unit	Definition	Corresponding PID data monitor item
FUELSYS	OL/CL/OL-Drive/OL-Fault/CL-Fault	Fuel system status	FUELSYS
LOAD_C	%	Calculated engine load	—
ECT	°C	Engine coolant temperature	ECT
SHRTFT1	%	Short term fuel trim	SHRTFT1
LONGFT1	%	Long term fuel trim	LONGFT1
MAP	Pa	Manifold absolute pressure	MAP
RPM	RPM	Engine speed	RPM
VSS	KPH	Vehicle speed	VSS
SPARKADV	°	Ignition timing	SPARKADV
IAT	°C	Intake air temperature	IAT
MAF	g/sec	Mass airflow	MAF
TP1	%	Throttle valve position No.1	TP1
EG_RUN_TIME	—	Time from engine start	—
SEGRP_DSD	%	Target EGR valve position	SEGRP DSD
EVAPCP	%	Purge solenoid valve controlled value	EVAPCP
FLI	%	Fuel level in fuel tank	—
CLR_CNT	—	Number of warm-up cycle after DTC cleared	—
CLR_DIST	km	Mileage after DTC cleared	—
FTP	Pa	Fuel tank pressure	—
BARO	Pa	Barometric pressure	—
CATT11_DSD	°C	Estimated catalytic converter temperature	CATT11_DSD
VPWR	V	Module supply voltage	VPWR
LOAD	%	Engine load	LOAD
EQ_RAT11_DSD	—	Target equivalence ratio (lambda)	EQ_RAT11_DSD
TP REL	%	Relative throttle position	TP REL
AAT	°C	Ambient air temperature	—
TP2	%	Throttle valve position No.2	TP2
APP1	%	Accelerator pedal position No.1	APP1
APP2	%	Accelerator pedal position No.2	APP2
ETC_DSD	%	Target throttle valve position	ETC_DSD

On-Board System Readiness Tests Access Procedure

1. Connect the M-MDS to the DLC-2.

am3uuw00003405

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

• When using the IDS (laptop PC)

1. Select “Powertrain”.

2. Select “OBD Test Modes”.

3. Select “Mode 1 Powertrain Data”.

4. Select “PCM”.

• When using the PDS (Pocket PC)

1. Select “OBDII Modes”.

2. Select “Mode 1 Powertrain Data”.

3. Select “PCM”.

3. Then, select the “***SUP” and “**EVAL” PIDs in the PID selection screen.

4. Monitor those PIDs and check it system monitor is completed.

PID/DATA Monitor and Record Procedure

Note

• The PID data screen function is used for monitoring the calculated value of input/output signals in the module. Therefore, if the monitored value of the output parts is not within the specification, it is necessary to inspect the monitored value of input parts corresponding to the applicable output part control. In addition, because the system does not display an output part malfunction as an abnormality in the monitored value, it is necessary to inspect the output parts individually.

1. Connect the M-MDS to the DLC-2.

am3uuw00003405

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

• When using the IDS (laptop PC)

1. Select “DataLogger”.

2. Select “Modules”.

3. Select “PCM”.

• When using the PDS (Pocket PC)

1. Select “Module Tests”.

2. Select “PCM”.

3. Select “DataLogger”.

3. Select the applicable PID from the PID table.

4. Verify the PID data according to the detections on the screen.

Diagnostic Monitoring Test Results Access Procedure

1. Connect the M-MDS to the DLC-2.

am3uuw00003405

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

• When using the IDS (laptop PC)

1. Select “Powertrain”.

2. Select “OBD Test Modes”.

3. Select “Mode 6 On-Board Test Results”.

• When using the PDS (Pocket PC)

1. Select “OBDII Modes”.

2. Select “Mode 6 On-Board Test Results”.

3. Verify the diagnostic monitoring test result according to the directions on the screen.

Active Command Modes Procedure

1. Connect the M-MDS to the DLC-2.

am3uuw00003405

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

• When using the IDS (laptop PC)

1. Select “DataLogger”.

2. Select “Modules”.

3. Select “PCM”.

• When using the PDS (Pocket PC)

1. Select “Module Tests”.

2. Select “PCM”.

3. Select “DataLogger”.

3. Select the simulation items from the PID table.

4. Perform the simulation function, inspect the operations for each parts.

• If the operation of output parts cannot be verified after the active command mode inspection is performed, this could indicate the possibility of an open or short circuit, sticking, or operation malfunction in the output parts.