ON-BOARD DIAGNOSTIC SYSTEM TEST MODE [PCM (SKYACTIV-D 1.5)]


id0102j6142500


Diagnostic Test Mode

•  To match the OBD regulations, the following diagnostic test modes have been supported.

Diagnostic test mode

Item

Mode 01
Sending diagnostic data (PID data monitor/On-board system readiness test)
Mode 02
Sending freeze frame data
Mode 03
Sending emission-related malfunction code (Diagnostic trouble code: DTC)
Mode 04
Clearing/resetting emission-related malfunction information
Mode 07
Sending continuous monitoring system test results (Pending code)
Mode 08
On-board device control (Simulation test, active command mode)
Mode 09
Request vehicle information


Sending Diagnostic Data (Mode 01)


PID data monitor

•  The PID data monitor items are shown below.

PID data monitor table

—: Not applicable

Full names

Unit

Monitor status since DTCs cleared
Undefined/Not Used
LOAD
%
ECT
°C, °F
MAP
kPa, Bar, psi
Engine speed
rpm
Vehicle speed
km/h, mph
IAT
°C, °F
MAF
g/s
Intake shutter valve position
%
OBD requirement according to vehicle design
Time since engine start
sec
Distance travelled while check engine light is activated
km, miles
Common rail pressure
kPa, Bar, psi
Remaining fuel
%
Number of warm-up since DTCs cleared
Count
Distance travelled since DTCs cleared
km, miles
Barometric pressure
kPa, Bar, psi
PCM power supply voltage
V
Relative intake shutter valve position
%
Ambient temperature
°C, °F
Absolute intake shutter valve position
%
Accelerator pedal position No.1
%
Accelerator pedal position No.2
%
Intake shutter valve control desired value
%
External test equipment configuration information #1
Undefined/Not Used
V
mA
kPa, Bar, psi
External test equipment configuration information #2
g/s
Fuel type which is used
Absolute common rail pressure
kPa, Bar, psi
Relative APP
%
Engine oil temperature
°C, °F
Fuel injection timing
°(deg)
MAF sensor
g/s
ECT
°C, °F
IAT sensor No.1
°C, °F
HP-EGR control valve actual opening angle
%
HP-EGR control valve desired value
%
Intake shutter valve control command
%
Common rail pressure control system desired value
kPa, Bar, psi
Common rail temperature
°C, °F
MAP
kPa, Bar, psi
MAP desired value
kPa, Bar, psi
Turbocharger with variable turbine geometry desired position
%
Turbocharger with variable turbine geometry actual position
%
Actuator position sensor (turbocharger with variable turbine geometry) voltage
V
Exhaust gas pressure
kPa, Bar, psi
Turbocharger with variable turbine geometry turbine revolution
rpm
Boost air temperature
°C, °F
Exhaust gas temperature (No.1)
°C, °F
Exhaust gas temperature (No.2)
°C, °F
Exhaust gas temperature (No.3)
°C, °F
Exhaust gas temperature (No.4)
°C, °F
Exhaust gas pressure sensor No.2 value
kPa, Bar, psi


Sending Freeze Frame Data (Mode 02)

Freeze frame data
•  The freeze frame data consists of data for vehicle and engine control system operation conditions when malfunctions in the engine control system are detected and stored in the PCM.
•  Freeze frame data is stored at the instant the check engine light illuminates, and only a part of the DTC data is stored.
•  For the freeze frame data, if there are several malfunctions in the engine control system, the data for the malfunction which occurred initially is stored. Thereafter, if a misfire or fuel injection control malfunction occurs, data from the misfire or fuel injection control malfunction is written over the initially stored data. However, if the initially stored freeze frame data is a misfire or fuel injection control malfunction, it is not overwritten.
Snapshot data
•  The snapshot data stores the currently detected DTC data.
•  The recording timing for the freeze frame data/snapshot data differs depending on the number of DTC drive cycles.
―  For a DTC with a drive cycle number 1, only the malfunction determination data is recorded.
―  For a DTC with a drive cycle number 2, both the malfunction determination and undetermined data is recorded.

Freeze frame data table

—: Not applicable

Freeze frame data item

Unit

Description

Corresponding PID data monitor item

LOAD
%
Engine load
LOAD
ECT
°C, °F
Engine coolant temperature
ECT
RPM
RPM
Engine speed
RPM
VS
KPH
Vehicle speed
VSS
MAF
g/sec
Mass airflow
MAF
TP
%
Intake shutter valve position
ISV_POS
FRP
Pa
Fuel pressure at common rail
FRP
FLI
%
Fuel level in fuel tank
FLI
CLRDIST
km, ft, mi
Mileage after DTC cleared
CLR_DIST
BARO
Pa
Barometric pressure
BARO
VPWR
V
Module supply voltage
VPWR
TP_REL
%
Relative throttle position
TP_REL
AAT
°C, °F
Ambient air temperature
IAT
APP_D
%
Accelerator pedal position No.1
APP1
APP_E
%
Accelerator pedal position No.2
APP2
TAC_PCT
%
Intake shutter valve control desired value
ISV_DSD
EOT
°C, °F
Engine oil temperature
EOT
EGR_A_CMD
%
HP-EGR control valve desired value
HPEGR_DSD
EGR_A_ACT
%
HP-EGR control valve actual value
HPEGR_ACT
FRP_A_CMD
Pa
Commanded fuel pressure at common rail
FRP_DSD
FRT_A
°C, °F
Fuel temperature at common rail
FRT
BP_A_CMD
Pa
Commanded boost air pressure
MAP_DSD
BP_A_ACT
Pa
Actual measured boost air pressure
MAP
VGT_A_CMD
%
Turbocharger with variable turbine geometry position desired value
VGTURB_DSD
VGT_A_ACT
%
Turbocharger with variable turbine geometry position actual value
VGTURB_ACT
EP_1
Pa
Exhaust gas pressure sensor No.1 value
EXHPRES1
TCA_RPM
RPM
Turbocharger with variable turbine geometry turbine speed
VGTURB_RPM
CACT11
°C, °F
Boost air temperature
CACT11
EGT11
°C, °F
Exhaust gas temperature sensor No.1 value
EXHTEMP1
EGT12
°C, °F
Exhaust gas temperature sensor No.2 value
EXHTEMP2
EGT13
°C, °F
Exhaust gas temperature sensor No.3 value
EXHTEMP3
EGT14
°C, °F
Exhaust gas temperature sensor No.4 value
EXHTEMP4
DPF1_DP
Pa
Exhaust gas pressure sensor No.2 value
EXHPRESS_DIF


Snapshot data table

—: Not applicable

Snapshot data item

Definition

Data read/use method

Unit

Corresponding PID data monitor item

AAT
Ambient air temperature
°C, °F
IAT
ALT_CUR_DSD
Generator target generated current
A
ALTT_V
Generator output voltage
V
ALTT_V
APP_R
Relative accelerator pedal position
%
APP1
Accelerator pedal position No.1
%
APP1
APP2
Accelerator pedal position No.2
%
APP2
BARO
Barometric pressure
KPa
BARO
BATT_RES
Battery internal resistance (estimated)
ohm
BATT_RES
BP_A_ACT
Manifold absolute pressure No.2 value
KPa
MAP
BP_A_CMD
Commanded manifold absolute pressure No.2
KPa
MAP_DSD
BP_A_ST
Manifold absolute pressure No.2 control status
Open Loop/Closed Loop/Fault present
CACT11
Boost air temperature sensor No.1 value
°C, °F
CACT11_DSD
Commanded boost air temperature sensor No.1
°C, °F
CLR_CNT
Number of warm-up cycle after DTC cleared
CLR_DIST
Mileage after DTC cleared
Km, ft, mi
CLR_DIST
DPF_REGEN_PCT
Specified value for performing diesel particulate filter regeneration
%
DPF_REGN_AVGD
Average of drive distance from previous diesel particulate filter regeneration to next diesel particulate filter regeneration
Km, ft, mi
DPF_REGN_STAT
Diesel particulate filter regeneration condition
No/Yes
DPF_REGN_TYP
Diesel particulate filter regeneration type
Passive/Active
DTC
DTC causing snap shot data record
ECT
Engine coolant temperature
°C, °F
ECT
ECT1
Engine coolant temperature No.1
°C, °F
ECT1_SUP
Engine coolant temperature No.1 support
No/Yes
ECT2
Engine coolant temperature No.2
°C, °F
ECT2_SUP
Engine coolant temperature No.2 support
No/Yes
EG_RUN_TIME
Time from engine start
hh:mm:ss
EGR_ERR
Percentage of abnormal EGR
%
EGRP
EGR valve position
%
EGRP_ACT
EGR valve actual opening angle
%
EGRP_ACT
EGRT11
Exhaust gas recirculation temperature
°C, °F
EGRT12
Low pressure side exhaust gas recirculation temperature
°C, °F
EOT
Engine oil temperature
°C, °F
EOT
EP_1
Exhaust gas pressure sensor No.1 value
KPa
EXHPRES1
EQ_RAT11_DSD
Target equivalence ratio (lambda)
ETC_DSD
Intake shutter valve control desired value
%
ISV_DSD
EVAPCP
Purge solenoid valve controlled value
%
EXHPRESS_DIF
Exhaust gas pressure sensor No.2 value
KPa
EXHPRESS_DIF
EXHTEMP1
Exhaust gas temperature sensor No.1 value
°C, °F
EXHTEMP
EXHTEMP2
Exhaust gas temperature sensor No.2 value
°C, °F
EXHTEMP1
EXHTEMP3
Exhaust gas temperature sensor No.3 value
°C, °F
EXHTEMP2
FLI
Fuel level in fuel tank
%
FRP
Fuel pressure at common rail (absolute)
KPa
FRP
FRP_A
Fuel pressure at common rail
KPa
FRP_A_CMD
Commanded fuel pressure at common rail
KPa
FRP_DSD
FRT
Fuel temperature at common rail
°C, °F
FRT
FTP
Fuel tank pressure
Pa
FUEL_PRES
Fuel pressure
KPa
FRP
FUEL_RATE
Percentage of fuel consumption
l/min
FUEL_TIMING
Main fuel injection timing related to top dead center
°(deg)
FUEL_TYP
Type of fuel currently being utilized by the vehicle
NONE/Gas/METH/ETH/DSL/ELEC
FUELSYS
Fuel system status
OL/CL/OL-Drive/OL-Fault/CL-Fault
IAT
Intake air temperature No.1
°C, °F
IAT11
Intake air temperature No.1 value
°C, °F
IAT12
Intake air temperature No.2 value
°C, °F
IAT13
Intake air temperature No.3 value
°C, °F
IAT13
LOAD_C
Calculated engine load
%
LOAD
LONGFT12
Long term fuel trim (HO2S)
%
LPEGR_ERR
Percentage of abnormal low pressure side EGR
%
LPEGRP
Low pressure EGR valve position
%
LPEGRP_ACT
Low pressure EGR valve actual opening angle
%
MAF
Mass airflow
g/sec
MAF_A
MAF sensor value
g/sec
MAF
NOX_ADS_DESULF
Desulfuration condition of NOx adsorbent
No/Yes
NOX_ADS_REGEN
Regeneration condition of NOx adsorbent
No/Yes
REGRP
Regulating valve position
%
REGVP
REGVP_DSD
Regulating valve position desired value
%
REGVP_DSD
RPM
Engine speed
RPM
RPM
SEGRP_DSD
Target EGR valve position
%
SHRTFT12
Short term fuel trim (HO2S)
%
TAC_A_CMD
Commanded throttle valve actuator control
%
TCA_CINP
Manifold absolute pressure No.1 value
KPa
TCA_CINP
TCA_RPM
Turbine speed of turbocharger with variable turbine geometry
RPM
TCB_CINP
Manifold absolute pressure No.1 value
km, ft, mi
TOTAL_DIST
Total distance
The distance traveled when the PCM detected a DTC can be calculated by performing the following procedure.
1.  Verify the odometer value in the instrument cluster.
2.  Verify the snapshot data item TOTAL_DIST.
3.  Subtract 2 from 1.
KPa
TOTAL_TIME
Total energization time for module
The elapsed time when the PCM detected a DTC can be calculated by performing the following procedure.
1.  Verify the instrument cluster PID item TOTAL_TIME of the instrument cluster.
2.  Verify the snapshot data item TOTAL_TIME.
3.  Subtract 2 from 1.
hh:mm:ss
TP_A_REL
Relative throttle valve position
%
TP_REL
Relative throttle position
%
TP1
Intake shutter valve position
%
ISV_POS
TP2
Throttle valve position No.2
%
TQ_ACT
Actual engine torque value
%
TQ_DD
Engine torque requested by driver
%
VGT_A_ACT
Actual measured value of turbocharger actuator position control
%
VGT_A_CMD
Target value of turbocharger actuator position control
%
VPWR
Module supply voltage
V
VPWR
VSS
Vehicle speed
KPH
VSS


Status Byte for DTC

•  The two digits (two digits after hyphen (-)) after the 7-digit DTC.
am6zzn00002906
•  A code which indicates the pending code, current/past malfunction status, or warning illumination status.
•  Can be read by performing a CMDTC self-test using the Mazda Modular Diagnostic System (M-MDS).
•  For details on the status byte, refer to the explanation on the Mazda Modular Diagnostic System (M-MDS) when reading the DTC.

Sending Emission-related Malfunction Code (DTC) (Mode 03)

•  The DTCs are shown below.

×: Applicable
—: Not applicable

DTC No.

Check engine light

Master warning light

i-stop warning light (amber)

Charging system warning light

Engine oil warning light

wrench indicator light

Diesel particulate filter indicator light

Condition

Fail-safe function

Drive cycle

Monitor item

Self test type*1

Memory function

B10A2:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Vehicle collision
1
Other
C
×
P0016:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Camshaft position/Crankshaft position correlation problem
×
1
CCM
C, R
×
P0030:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor heater control circuit range/performance problem
×
1
A/F sensor
C
×
P0047:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Turbocharger solenoid valve control circuit low input
×
1
CCM
C, O, R
×
P0048:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Turbocharger solenoid valve control circuit high input
×
1
CCM
C, O, R
×
P0072:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ambient temperature sensor circuit low input
1
Other
C, O, R
×
P0073:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Ambient temperature sensor circuit high input
1
Other
C, O, R
×
P007B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Boost air temperature sensor circuit range/performance problem
×
2
CCM
C
×
P007C:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Boost air temperature sensor circuit low input
×
1
CCM
C, O, R
×
P007D:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Boost air temperature sensor circuit high input
×
1
CCM
C, O, R
×
P0087:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Low fuel pressure malfunction in common rail fuel pressure control system
×
1
CCM
C
×
P0088:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
High fuel pressure malfunction in common rail fuel pressure control system
×
1
CCM
C
×
P0089:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
High fuel pressure malfunction in common rail fuel pressure control system
×
1
CCM
C
×
P0093:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel leakage from fuel pressure control system
×
1
CCM
C
×
P0096:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.2 circuit range/performance problem
×
2
CCM
C
×
P0097:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.2 circuit low input
×
1
CCM
C, O, R
×
P0098:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.2 circuit high input
×
1
CCM
C, O, R
×
P009B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve control circuit open
×
1
CCM
C
×
P009C:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve control circuit low input
×
1
CCM
C, R
×
P009D:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve control circuit high input
×
1
CCM
C, R
×
P009E:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve malfunction (stuck close)
×
1
CCM
C
×
P009F:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure relief valve control circuit (stuck on)
×
1
CCM
C
×
P0101:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAF sensor circuit range/performance problem
×
1
CCM
C, O
×
P0102:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAF sensor circuit low input
×
1
CCM
C, O, R
×
P0103:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAF sensor circuit high input
×
1
CCM
C, O, R
×
P0106:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAP sensor circuit range/performance problem
×
1
CCM
C
×
P0107:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAP sensor circuit low input
×
1
CCM
C, O, R
×
P0108:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
MAP sensor circuit high input
×
1
CCM
C, O, R
×
P0111:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.1 circuit range/performance problem
×
2
CCM
C
×
P0112:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.1 circuit low input
×
1
CCM
C, O, R
×
P0113:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
IAT sensor No.1 circuit high input
×
1
CCM
C, O, R
×
P0116:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
ECT sensor circuit range/performance problem
×
1
CCM
C
×
P0117:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
ECT sensor circuit low input
×
1
CCM
C, O, R
×
P0118:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
ECT sensor circuit high input
×
1
CCM
C, O, R
×
P0122:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve position sensor circuit low input
×
1
CCM
C, O, R
×
P0123:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve position sensor circuit high input
×
1
CCM
C, O, R
×
P0130:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor circuit range/performance problem
×
1
A/F sensor
C, O, R
×
P0131:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor circuit low input
×
1
A/F sensor
C, O, R
×
P0132:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor circuit high input
×
1
A/F sensor
C, O, R
×
P0134:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
A/F sensor circuit no activity detected
×
1
A/F sensor
C
×
P0181:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel temperature sensor circuit range/performance problem
×
2
CCM
C
×
P0182:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel temperature sensor circuit low input
×
1
CCM
C, O, R
×
P0183:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel temperature sensor circuit high input
×
1
CCM
C, O, R
×
P0191:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure sensor circuit range/performance problem
×
1
CCM
C
×
P0192:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure sensor circuit low input
×
1
CCM
C, O, R
×
P0193:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel pressure sensor circuit high input
×
1
CCM
C, O, R
×
P0196:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil temperature sensor circuit range/performance problem
2
CCM
C
×
P0197:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil temperature sensor circuit low input
1
CCM
C, O, R
×
P0198:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil temperature sensor circuit high input
1
CCM
C, O, R
×
P0201:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 circuit open
×
1
CCM
C, R
×
P0202:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 circuit open
×
1
CCM
C, R
×
P0203:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.3 circuit open
×
1
CCM
C, R
×
P0204:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.4 circuit open
×
1
CCM
C, R
×
P0219:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Engine overspeed condition
1
Other
C
×
P0234:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Turbocharger with variable turbine geometry overboost condition
2
Turbo system
C
×
P026A:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Charge air cooler efficiency below threshold
×
1
Other
C
×
P0299:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Turbocharger with variable turbine geometry underboost condition
2
Turbo system
C
×
P02EE:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 circuit: shorted to each other
×
1
CCM
C, R
×
P02EF:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 circuit: shorted to each other
×
1
CCM
C, R
×
P02F0:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.3 circuit: shorted to each other
×
1
CCM
C, R
×
P02F1:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.4 circuit: shorted to each other
×
1
CCM
C, R
×
P0313:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Misfire detected with low fuel
×
1
Other
C
×
P0336:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
CKP sensor circuit range/performance problem
×
2
CCM
C, R
×
P0337:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
CKP sensor circuit problem
×
1
CCM
C, R
×
P0339:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CKP sensor circuit range/performance problem
×
1
Other
C
×
P0341:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
CMP sensor circuit range/performance problem
2
CCM
C, R
×
P0342:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
CMP sensor circuit problem
1
CCM
C, R
×
P0401:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
HP-EGR flow insufficient detected
×
2
EGR system
C
×
P0402:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
HP-EGR flow excessive detected
×
1
EGR system
C
×
P0404:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Circuit malfunction in HP-EGR control valve DC motor control system
×
1
CCM
C, O, R
×
P0405:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
HP-EGR control valve position sensor circuit low input
×
1
CCM
C, O, R
×
P0406:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
HP-EGR control valve position sensor circuit high input
×
1
CCM
C, O, R
×
P0407:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR control valve position sensor circuit low input
×
1
CCM
C, O, R
×
P0408:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR control valve position sensor circuit high input
×
1
CCM
C, O, R
×
P0421:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Catalyst efficiency below threshold
2
Catalyst
C
×
P045B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR control valve control: circuit malfunction
×
1
CCM
C, O, R
×
P0471:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.1 circuit range/performance problem
×
2
CCM
C
×
P0472:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.1 circuit low input
×
1
CCM
C, O, R
×
P0473:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.1 circuit high input
×
1
CCM
C, O, R
×
P0475:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust shutter valve DC motor control circuit problem
×
1
CCM
C, O, R
×
P0476:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust shutter valve control duty signal error
×
1
CCM
C
×
P0480:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Fan control module No.1 control circuit problem
1
Other
C, O
×
P0481:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Fan control module No.2 control circuit problem
1
Other
C, O
×
P0488:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Duty signal error in HP-EGR control valve control system
×
1
CCM
C
×
P048D:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust shutter valve position sensor circuit low input
×
1
CCM
C, O, R
×
P048E:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust shutter valve position sensor circuit high input
×
1
CCM
C, O, R
×
P049B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR flow insufficient detected
×
2
EGR system
C
×
P049C:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LP-EGR flow excessive detected
×
1
EGR system
C
×
P0500:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
VSS circuit problem
×
1
CCM
C, O, R
×
P0504:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Brake switch circuit problem
×
2
Other
C
×
P0522:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil pressure sensor circuit low input
×
1
CCM
C, O, R
×
P0523:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil pressure sensor circuit high input
×
1
CCM
C, O, R
×
P0524:00
ON
OFF
OFF
OFF
ON
OFF
OFF
Engine oil pressure too low
×
1
CCM
C
×
P0532:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Refrigerant pressure sensor circuit low input
×
1
Other
C
×
P0533:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Refrigerant pressure sensor circuit high input
×
1
Other
C
×
P053B:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Blow-by heater relay control circuit low input
1
Other
C, O, R
×
P053C:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Blow-by heater relay control circuit high input
1
Other
C, O, R
×
P0545:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.1 circuit low input
×
1
CCM
C, O, R
×
P0546:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.1 circuit high input
×
1
CCM
C
×
P0555:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Power brake unit vacuum sensor circuit problem
×
1
Other
C, R
×
P055F:00
ON
OFF
OFF
OFF
ON
OFF
OFF
Engine oil pressure control circuit low oil pressure
×
1
CCM
C
×
P057F:00
OFF
ON
Flash
OFF
OFF
OFF
OFF
Power system: Battery deterioration
1
Other
C
×
P058A:00
OFF
OFF
Flash
ON*6
OFF
OFF
OFF
Current sensor: Function malfunction
×
1
Other
C
×
P059F:00*4
OFF
ON
OFF
OFF
OFF
OFF
OFF
Active air shutter: Opening angle abnormality (spinning free)
×
1
Other
C
×
P05A0:00*4
OFF
ON
OFF
OFF
OFF
OFF
OFF
Active air shutter: Opening angle abnormality (sticking)
×
1
Other
C
×
P05A3:00*4
OFF
ON
OFF
OFF
OFF
OFF
OFF
Active air shutter: Actuator internal malfunction
×
1
Other
C
×
P05C0:00*4
OFF
ON
OFF
OFF
OFF
OFF
OFF
Active air shutter: Actuator temperature abnormality
×
1
Other
C
×
P0601:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM memory check sum error
1
CCM
C, O, R
×
P0602:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PCM programming error
×
1
Other
C
×
P0605:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM memory check sum error
×
1
CCM
C
×
P0606:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM processor error
×
1
CCM
C, O, R
×
P0607:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Control module performance problem
×
1
CCM
C, O, R
×
P0610:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PCM vehicle configuration error
×
1
Other
C
×
P0615:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Starter/starter relay operation amount
1
Other
C
×
P062A:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Suction control valve circuit problem
×
1
CCM
C, R
×
P062B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM internal malfunction
×
1
CCM
C, O, R
×
P0642:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply circuit low input
×
1
CCM
C
×
P0643:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply circuit high input
×
1
CCM
C
×
P0646:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
A/C relay circuit low input
×
1
Other
C
×
P0647:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
A/C relay circuit high input
×
1
Other
C
×
P0652:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply control circuit low input
×
1
CCM
C
×
P0653:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply control circuit high input
×
1
CCM
C
×
P0670:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow control module control circuit problem
1
CCM
C, O
×
P0671:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow plug No.1 control circuit problem
1
CCM
C, O
×
P0672:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow plug No.2 control circuit problem
1
CCM
C, O
×
P0673:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow plug No.3 control circuit problem
1
CCM
C, O
×
P0674:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Glow plug No.4 control circuit problem
1
CCM
C, O
×
P0698:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply circuit low input
×
1
CCM
C
×
P0699:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Constant voltage power supply circuit high input
×
1
CCM
C
×
P06B8:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Internal control module non-volatile RAM error
×
1
CCM
C
×
P06DB:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil solenoid valve control circuit low input
×
1
Other
C, O, R
×
P06DC:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Engine oil solenoid valve control circuit high input
×
1
Other
C, O, R
×
P06DD:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Engine oil pressure switch control circuit high input
1
Other
C
×
P06DE:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Engine oil pressure switch control circuit low input
1
Other
C
×
P0703:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Brake switch input circuit problem
×
2
Other
C
×
P0704:00*2
ON
OFF
OFF
OFF
OFF
OFF
OFF
CPP switch input circuit problem
×
2
CCM
C
×
P07BE:00*2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Transmission indeterminate failure (failed to neutral)
1
Other
C
×
P0850:00*2
ON
OFF
OFF
OFF
OFF
OFF
OFF
Neutral switch No.1 input circuit problem
×
2
CCM
C
×
P0A06:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Electric water pump control circuit low input
1
Other
C, O
×
P0A07:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Electric water pump control circuit high input
1
Other
C, O
×
P0A0F:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Engine failed to restart
1
Other
C
×
P0A8D:00
OFF
ON
Flash
ON
OFF
OFF
OFF
Power supply system circuit low input
1
Other
C
×
P0A8F:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
Power system: Low input
1
Other
C
×
P0A94:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
DC-DC converter: control circuit signal error
1
Other
C
×
P0C73:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Electric water pump: abnormal operation
1
Other
C
×
P1051:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too low cylinder No.1
2
Fuel system
C
×
P1052:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too high cylinder No.1
2
Fuel system
C
×
P1053:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too low cylinder No.2
2
Fuel system
C
×
P1054:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too high cylinder No.2
2
Fuel system
C
×
P1055:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too low cylinder No.3
2
Fuel system
C
×
P1056:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too high cylinder No.3
2
Fuel system
C
×
P1057:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too low cylinder No.4
2
Fuel system
C
×
P1058:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Injection quantity too high cylinder No.4
2
Fuel system
C
×
P111A:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Engine coolant temperature is high
1
Other
C
×
P1140:00
OFF
OFF
OFF
OFF
OFF
ON*7
OFF
Sedimentor switch control circuit range/performance problem
1
Other
C
×
P1142:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Fuel Restriction Condition
×
1
Other
C
×
P115A:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Lack of remaining fuel (output restriction)
×
1
Other
C
×
P115B:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Lack of remaining fuel (fuel injection pause)
×
1
Other
C
×
P117A:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Record of torque restriction for piston protection
1
Other
C
×
P1200:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injection amount learning not completed
1
CCM
C
×
P1260:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Immobilizer system problem
1
Other
C
×
P1282:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Common rail control system problem
×
1
CCM
C
×
P1329:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Common rail pressure higher than desired (engine running)
×
1
CCM
C
×
P1336:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
CKP sensor/CMP sensor malfunction
1
Other
C
×
P1378:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector circuit low input
×
1
CCM
C, R
×
P1379:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector circuit high input
×
1
CCM
C, R
×
P1589:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve circuit range/performance problem
×
1
CCM
C
×
P1675:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector code not programmed
×
1
CCM
C
×
P1676:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector code mistakenly programmed
×
1
CCM
C
×
P167B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injection amount learning not completed in fuel injection system
1
CCM
C
×
P176E:00*2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Clutch stroke sensor/CPP switch/starter interlock switch correlation problem
×
1
Other
C
×
P1905:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Check connector circuit low input
1
Other
C
×
P2002:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Diesel particulate filter function decreased
2
Diesel particulate filter system
C
×
P2032:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.2 circuit low input
×
1
CCM
C, O, R
×
P2033:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.2 circuit high input
×
1
CCM
C
×
P2101:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve control circuit overcurrent
×
1
CCM
C, O, R
×
P2104:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve control system: Idle air control
×
1
CCM
C
×
P2105:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve actuator control system malfunction (forced engine shutdown)
1
Other
C
×
P2106:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Throttle Actuator Control System - Forced Limited Power
×
1
CCM
C
×
P2118:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Intake shutter valve control duty signal error
×
1
CCM
C
×
P2122:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.1 circuit low input
×
1
CCM
C, O, R
×
P2123:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.1 circuit high input
×
1
CCM
C, O, R
×
P2127:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.2 circuit low input
×
1
CCM
C, O, R
×
P2128:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.2 circuit high input
×
1
CCM
C, O, R
×
P2138:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
APP sensor No.1/No.2 correlation problem
×
1
CCM
C
×
P213B:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Circuit malfunction in LP-EGR control valve DC motor control system
×
1
CCM
C
×
P2146:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 and No.4 circuit abnormal operation
×
1
CCM
C, R
×
P2147:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 and No.4 circuit low input
×
1
CCM
C, R
×
P2148:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.1 and No.4 circuit high input
×
1
CCM
C, R
×
P2149:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 and No.3 circuit abnormal operation
×
1
CCM
C, R
×
P2150:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 and No.3 circuit low input
×
1
CCM
C, R
×
P2151:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Fuel injector No.2 and No.3 circuit high input
×
1
CCM
C, R
×
P2227:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
BARO sensor circuit range/performance problem
×
1
CCM
C
×
P2228:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
BARO sensor circuit low input
×
1
CCM
C, O, R
×
P2229:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
BARO sensor circuit high input
×
1
CCM
C, O, R
×
P2263:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Turbocharger solenoid valve range/performance problem
×
1
CCM
C
×
P2299:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Accelerator pedal: spring back malfunction
1
Other
C
×
P242C:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.3 circuit low input
×
1
CCM
C, O, R
×
P242D:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.3 circuit high input
×
1
CCM
C
×
P242F:00
ON
OFF
OFF
OFF
OFF
OFF
Flash
Diesel particulate filter excess accumulation (exceeded acceptable amount)
×
1
CCM
C
×
P243C:00
OFF
OFF
OFF
OFF
OFF
OFF
Flash
Abnormal diesel particulate filter regeneration interval short distance
1
Other
C
×
P244A:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.2 range/performance problem
×
1
Diesel particulate filter system
C
×
P2452:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Signal malfunction in exhaust gas pressure sensor No.2
1
Other
C
×
P2454:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.2 circuit low input
×
1
CCM
C, O, R
×
P2455:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas pressure sensor No.2 circuit high input
×
1
CCM
C, O, R
×
P2456:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Characteristic malfunction in exhaust gas pressure sensor No.2
×
1
CCM
C
×
P2458:00
OFF
OFF
OFF
OFF
OFF
OFF
Flash
Diesel particulate filter excess accumulation (mid)
×
1
Other
C
×
P2463:00
ON
OFF
OFF
OFF
OFF
OFF
Flash
Diesel particulate filter excess accumulation (large)
×
1
CCM
C
×
P246C:00
OFF
OFF
OFF
OFF
ON
OFF
OFF
Engine oil dilution, oil pressure decreased
1
Other
C
×
P2470:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.4 circuit low input
×
1
CCM
C, O, R
×
P2471:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Exhaust gas temperature sensor No.4 circuit high input
×
1
CCM
C
×
P2502:00
OFF
OFF
Flash
ON*6
OFF
OFF
OFF
Generator system: Malfunction in voltage generated by generator
×
1
Other
C
×
P2503:00
OFF
OFF
Flash
ON*6
OFF
OFF
OFF
Generator system: Voltage generated by generator is low
×
1
Other
C
×
P2504:00
OFF
OFF
Flash
ON*6
OFF
OFF
OFF
Generator system: Voltage generated by generator is high
×
1
Other
C
×
P2507:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
PCM battery voltage low input
×
1
CCM
C
×
P250A:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Engine oil level signal: engine oil level sensor malfunction
1
Other
C
×
P250C:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Engine oil level sensor power supply circuit malfunction
1
Other
C
×
P250F:00
OFF
OFF
OFF
OFF
OFF
ON
OFF
Engine oil level signal: engine oil level low
1
Other
C
×
P252F:00
OFF
OFF
OFF
OFF
OFF
ON
OFF
Engine oil level signal: engine oil level high
1
Other
C
×
P253F:00
OFF
OFF
OFF
OFF
ON
OFF
OFF
Engine oil deteriorated
1
Other
C
×
P2564:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Actuator position sensor (turbocharger with variable turbine geometry) circuit low input
×
1
CCM
C, R
×
P2565:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Actuator position sensor (turbocharger with variable turbine geometry) circuit high input
×
1
CCM
C, O, R
×
P2579:00
OFF
ON
OFF
OFF
OFF
OFF
OFF
Speed sensor assy (turbocharger with variable turbine geometry) range/performance problem
×
1
Other
C
×
P2580:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Speed sensor assy (turbocharger with variable turbine geometry) circuit low input
×
1
CCM
C
×
P2581:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Speed sensor assy (turbocharger with variable turbine geometry) circuit high input
×
1
CCM
C
×
P2610:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Malfunction in instrument cluster
×
2
CCM
C
×
P2681:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Circuit malfunction in coolant control valve control system
×
1
CCM
C, O, R
×
P2682:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Coolant control valve position sensor circuit low input
1
CCM
C, O, R
×
P2683:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Coolant control valve position sensor circuit high input
1
CCM
C, O, R
×
P26A3:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Coolant control valve control: high duty malfunction
×
1
CCM
C, O
×
P2A00:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
Atmosphere learning malfunction in A/F sensor circuit
×
1
A/F sensor
C
×
U0073:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CAN system communication error (HS CAN)
Other
C, O, R
×
U0074:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CAN system communication error (local CAN between PCM and TCM)
Other
C
×
U0101:00
ON
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error with TCM
×
1
CCM
C
×
U0104:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CAN communication: communication error to radar unit
×
1
Other
C
×
U0106:00
ON
OFF
OFF
OFF
OFF
OFF
OFF
LIN communication system: glow control module information communication error with PCM
×
1
CCM
C, O
×
U0121:00
ON
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error with DSC HU/CM
×
1
CCM
C
×
U0131:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error with EPS control module
1
Other
C
×
U0140:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error with front body control module (FBCM)
1
Other
C
×
U0151:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error with SAS control module
1
Other
C
×
U0155:00
ON
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error with instrument cluster
×
1
CCM
C
×
U0214:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN communication: communication error with start stop unit
1
Other
C
×
U023A:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
CAN communication: communication error with forward sensing camera (FSC)
1
Other
C
×
U0284:00*4
OFF
ON
OFF
OFF
OFF
OFF
OFF
LIN communication system: Communication error between active air shutter and PCM
×
1
Other
C
×
U0298:00
OFF
OFF
Flash
OFF
OFF
OFF
OFF
CAN/LIN communication system: DC-DC converter information communication error with front body control module (FBCM)
1
Other
C
×
U0302:00*3
ON
OFF
OFF
OFF
OFF
OFF
OFF
TCM processor error
×
1
CCM
C
×
U0305:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Radar unit error
1
Other
C
×
U0315:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DSC HU/CM error
1
Other
C
×
U0320:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
EPS control module error
1
Other
C
×
U0323:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Instrument cluster error
1
Other
C
×
U0336:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SAS control module error
1
Other
C
×
U0338:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Start stop unit error
1
Other
C
×
U053B:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Abnormal message from forward sensing camera (FSC)
1
Other
C
×
U1100:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
LIN communication: communication error to engine oil level sensor
1
Other
C
×
U2300:00
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Global central configuration error
1
Other
C
×
U3000:41
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PCM processor error
1
Other
C
×

*1  :C: CMDTC self test, O: KOEO self test, R: KOER self test
*2  :MTX
*3  :ATX
*4  :Vehicles with active air shutter
*5  :Displays a message related to a vehicle system malfunction in the display. (With center display or type B instrument cluster)
*6  :Displays a message related to a charge system malfunction in the display. (With center display or type B instrument cluster)
*7  :Displays a message related to a sedimentor in the display. (With center display or type B instrument cluster)
*8  :Displays a message related to a diesel particulate filter malfunction in the display. (With center display or type B instrument cluster)
*9  :Displays a message related to an engine hydraulic pressure malfunction in the display. (With center display or type B instrument cluster)

Sending Continuous Monitoring System Test Results (pending code) (Mode 07)

•  These appear when a problem is detected in a monitored system.

1-drive cycle type

•  If any problems are detected in the first drive cycle, pending codes will be stored in the PCM memory, as well as DTCs.
•  After pending codes are stored, if the PCM determines that the system is normal in any future drive cycle, the PCM deletes the pending codes.


2-drive cycle type

•  The code for a failed system is stored in the PCM memory in the first drive cycle. If the PCM determines that the system returned to normal or the problem was mistakenly detected, and deletes the pending code. If the problem is found in the second drive cycle too, the PCM determines that the system has failed, and stores the pending codes, and the DTCs.
•  After pending codes are stored, if the PCM determines that the system is normal in any future drive cycle, the PCM deletes the pending codes.