DTC B11DB:86 [FRONT BODY CONTROL MODULE (FBCM)]

id0902p2007900

Description

Error signal received from current sensor

Detection condition

•  Front body control module (FBCM) receives the error signals from the current sensor for 5 s or more with the ignition switched ON (engine off or on).

Fail-safe function

Not applicable

Possible cause

•  Current sensor connector or terminal malfunction

•  Front body control module (FBCM) connector or terminal malfunction

•  Current sensor malfunction

•  Front body control module (FBCM) malfunction

System wiring diagram

Not applicable

Description	Error signal received from current sensor
Detection condition	• Front body control module (FBCM) receives the error signals from the current sensor for 5 s or more with the ignition switched ON (engine off or on).
Fail-safe function	Not applicable
Possible cause	• Current sensor connector or terminal malfunction • Front body control module (FBCM) connector or terminal malfunction • Current sensor malfunction • Front body control module (FBCM) malfunction
System wiring diagram	Not applicable

Diagnostic Procedure

Step	Inspection		Action
1	VERIFY FRONT BODY CONTROL MODULE (FBCM) DTCs AGAIN • Clear the DTC for the front body control module (FBCM) using the M-MDS. (See CLEARING DTC [FRONT BODY CONTROL MODULE (FBCM)].) • Switch the ignition ON (engine off or on) and wait for 5 s or more. • Retrieve the front body control module (FBCM) DTCs using the M-MDS. (See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)].) • Is the same DTC displayed?	Yes	Go to the next step.
1		No	Go to Step 6.
2	INSPECT CURRENT SENSOR CONNECTOR CONDITION • Switch the ignition off. • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Disconnect the current sensor connector. • Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. • Is the connector normal?	Yes	Go to the next step.
2		No	Repair or replace the connector, then go to Step 5.
3	INSPECT FRONT BODY CONTROL MODULE (FBCM) CONNECTOR CONDITION • Disconnect the front body control module (FBCM) connector. • Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. • Is the connector normal?	Yes	Go to the next step.
3		No	Repair or replace the connector, then go to Step 5.
4	INSPECT CURRENT SENSOR • Inspect the current sensor. (See CURRENT SENSOR INSPECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See CURRENT SENSOR INSPECTION [SKYACTIV-D 1.5].) (See CURRENT SENSOR INSPECTION [SKYACTIV-D 2.2].) • Is the current sensor normal?	Yes	Go to the next step.
4		No	Replace the current sensor, then go to the next step. (See CURRENT SENSOR REMOVAL/INSTALLATION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See CURRENT SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 1.5].) (See CURRENT SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
5	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Always reconnect all disconnected connectors. • Reconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Clear the DTC for the front body control module (FBCM) using the M-MDS. (See CLEARING DTC [FRONT BODY CONTROL MODULE (FBCM)].) • Switch the ignition ON (engine off or on) and wait for 5 s or more. • Retrieve the front body control module (FBCM) DTCs using the M-MDS. (See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)].) • Is the same DTC displayed?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the front body control module (FBCM). (See FRONT BODY CONTROL MODULE (FBCM) REMOVAL/INSTALLATION.) Go to the next step.
5		No	Go to the next step.
6	VERIFY IF OTHER DTCs DISPLAYED • Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [FRONT BODY CONTROL MODULE (FBCM)].)
6		No	DTC troubleshooting completed.