OBD DRIVE MODE [MZR 2.0, MZR 2.5]

id0102g3815800

•  Performing the Drive Mode inspects the OBD system for proper operation and must be performed to ensure that no additional DTCs are present.
•  During the Drive Mode, the following systems are inspected:
―  Oxygen sensor (A/F sensor, HO2S)
―  Oxygen sensor heater (A/F sensor heater, HO2S heater)
―  Catalytic converter (TWC)
―  Fuel system and Misfire
Caution
•  While performing the Drive Mode, always operate the vehicle in a safe and lawful manner.
•  When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD function and inspect later.
Note
•  Vehicle speed and engine speed detected by the PCM may differ from that indicated by the speedometer and tachometer. Use the M-MDS to monitor vehicle speed.
•  If the OBD system inspection is not completed during the Drive Mode, the following causes are considered:
―  The OBD system detects the malfunction.
―  The Drive Mode procedure is not completed correctly.
•  Disconnecting the battery will reset the memory. Do not disconnect the battery during and after the Drive Mode.
•  The M-MDS can be used at anytime through the course of the Drive Mode to monitor the completion status. Monitoring can be done by viewing the ON BOARD SYSTEM READINESS menu.

Mode 03 (A/F sensor heater, HO2S heater, A/F sensor, HO2S and TWC Repair Verification Drive Mode)

1.  Start the engine and warm it up completely.

2.  Verify that all accessory loads (A/C, headlights, blower fan, rear window defroster) are off.

3.  Drive the vehicle as shown in the graph: first drive in zone 0, then A or B, followed by C or D, finally E or F. The driving conditions before driving at constant speed are not specified.

ATX

am3zzw00005284

Zone

Shift Position

Vehicle Speed

Time
0
N position
0 km/h {0 mph}
T1: 455 s or more
A
M (3rd) range
50—65 km/h {31—41 mph}
T2: 30 s or more
B
M (4th) range
65—100 km/h {41—62 mph}
C
M (2nd) range
65—75 km/h {41—47 mph}
T3: 20 s or more
D
M (3rd) range
75—100 km/h {47—62 mph}
E
M (4th) range
50—75 km/h {31—47 mph}
T4: 120 s or more
F
D range
75—100 km/h {47—62 mph}

MTX

am3zzw00007701

Zone

Shift Position

Vehicle Speed

Time
0
Neutral/Low
0 km/h {0 mph}
T1: 455 s or more
A
3rd
40—50 km/h {25—31 mph}
T2: 30 s or more
B
4th
65—75 km/h {41—46 mph}
C
3rd
60—75 km/h {38—46 mph}
T3: 20 s or more
D
3rd
75—100 km/h {47—62 mph}
E
4th
50—75 km/h {32—46 mph}
T4: 120 s or more
F
5th
70—95 km/h {44—59 mph}

4.  Stop the vehicle and access ON BOARD SYSTEM READINESS to inspect the Drive Mode completion status.

•  If completed, RFC changes from No to Yes.
•  If not completed, switch the ignition to off then go back to Step 3.

5.  Verify that no DTCs are available.