DTC P2122:00 [MZR 2.3 DISI Turbo]

id0102g4326500

DTC P2122:00

APP sensor No.1 circuit low input

DETECTION CONDITION

•  The PCM monitors the APP sensor No.1 signal. If the PCM detects that the APP sensor No.1 voltage is below 0.12 V, the PCM determines that the APP sensor No.1 circuit has a malfunction.

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The MIL illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

•  The DTC is stored in the PCM memory.

POSSIBLE CAUSE

•  APP sensor connector or terminals malfunction

•  Short to ground in wiring harness between the following terminals:

―  APP sensor terminal A—PCM terminal 1Q

―  APP sensor terminal B—PCM terminal 1Y

•  PCM connector or terminals malfunction

•  APP sensor No.1 signal circuit and ground circuit are shorted to each other.

•  Open circuit in wiring harness between the following terminals:

―  APP sensor terminal A—PCM terminal 1Q

―  APP sensor terminal B—PCM terminal 1Y

•  APP sensor No.1 malfunction

•  PCM malfunction

DTC P2122:00	APP sensor No.1 circuit low input
DETECTION CONDITION	• The PCM monitors the APP sensor No.1 signal. If the PCM detects that the APP sensor No.1 voltage is below 0.12 V, the PCM determines that the APP sensor No.1 circuit has a malfunction. Diagnostic support note • This is a continuous monitor (CCM). • The MIL illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • The DTC is stored in the PCM memory.
POSSIBLE CAUSE	• APP sensor connector or terminals malfunction • Short to ground in wiring harness between the following terminals: ― APP sensor terminal A—PCM terminal 1Q ― APP sensor terminal B—PCM terminal 1Y • PCM connector or terminals malfunction • APP sensor No.1 signal circuit and ground circuit are shorted to each other. • Open circuit in wiring harness between the following terminals: ― APP sensor terminal A—PCM terminal 1Q ― APP sensor terminal B—PCM terminal 1Y • APP sensor No.1 malfunction • PCM malfunction

Diagnostic procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT APP SENSOR CONNECTOR CONDITION • Switch the ignition to off. • Disconnect the APP sensor connector. • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
3		No	Go to the next step.
4	INSPECT APP SENSOR NO.1 CIRCUIT FOR SHORT TO GROUND • APP sensor connector is disconnected. • Inspect for continuity between the following terminals (wiring harness-side) and body ground: ― APP sensor terminal A ― APP sensor terminal B • Is there continuity?	Yes	If the short to ground circuit could be detected: • Repair or replace the wiring harness for a possible short to ground. If the short to ground circuit could not be detected: • Replace the PCM (short to ground in PCM internal circuit). (See PCM REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].) Go to Step 9.
4		No	Go to the next step.
5	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
5		No	Go to the next step.
6	INSPECT APP SENSOR NO.1 SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER • APP sensor and PCM connectors are disconnected. • Inspect for continuity between APP sensor terminals B and C (wiring harness-side). • Is there continuity?	Yes	Repair or replace the wiring harness for a possible short to each other, then go to Step 9.
6		No	Go to the next step.
7	INSPECT APP SENSOR NO.1 CIRCUIT FOR OPEN CIRCUIT • APP sensor and PCM connectors are disconnected. • Inspect for continuity between the following terminals (wiring harness-side): ― APP sensor terminal A—PCM terminal 1Q ― APP sensor terminal B—PCM terminal 1Y • Is there continuity?	Yes	Go to the next step.
7		No	Repair or replace the wiring harness for a possible open circuit, then go to Step 9.
8	INSPECT APP SENSOR NO.1 • Reconnect all disconnected connectors. • Inspect the APP sensor No.1. (See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION [MZR 2.3 DISI Turbo].) • Is there any malfunction?	Yes	Replace the accelerator pedal, then go to the next step. (See ACCELERATOR PEDAL REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].)
8		No	Go to the next step.
9	VERIFY DTC TROUBLESHOOTING COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [MZR 2.3 DISI Turbo].) • Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST [MZR 2.3 DISI Turbo].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].) Go to the next step.
9		No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [MZR 2.3 DISI Turbo].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [MZR 2.3 DISI Turbo].)
10		No	DTC troubleshooting completed.