REAR MAP LIGHT REMOVAL/INSTALLATION


id091800810500

Note
•  The rear map light can be removed without having to remove the headliner from the vehicle.

1.  Perform the following procedure.

4SD
1.  Set the wheel blocks for both the front and rear wheels.
3.  Shift the selector lever from the P position to the D position (ATX).
4.  Remove the sunroof seaming welt. (with sunroof system)
5.  Remove the following parts:
1.  A-pillar trim (See A-PILLAR TRIM REMOVAL/INSTALLATION.)
2.  Sunvisor (See SUNVISOR REMOVAL/INSTALLATION.)
3.  Front map light (dual light type) (See FRONT MAP LIGHT REMOVAL/INSTALLATION.)
4.  Assist handle (See ASSIST HANDLE REMOVAL/INSTALLATION.)
5.  Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
6.  Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION.)
7.  B-pillar lower trim (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
8.  Adjust anchor cover (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
9.  Upper anchor installation bolt on the seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
10.  B-pillar upper trim (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
6.  Set the tire house trim aside. (See TIRE HOUSE TRIM REMOVAL/INSTALLATION.)
7.  Remove the C-pillar trim. (See C-PILLAR TRIM REMOVAL/INSTALLATION.)
8.  Remove the headliner. (See HEADLINER REMOVAL/INSTALLATION.)
5HB
1.  Set the wheel blocks for both the front and rear wheels.
3.  Shift the selector lever from the P position to the D position (ATX).
4.  Remove the sunroof seaming welt. (with sunroof system)
5.  Remove the following parts:
1.  A-pillar trim (See A-PILLAR TRIM REMOVAL/INSTALLATION.)
2.  Sunvisor (See SUNVISOR REMOVAL/INSTALLATION.)
3.  Front map light (dual light type) (See FRONT MAP LIGHT REMOVAL/INSTALLATION.)
4.  Assist handle (See ASSIST HANDLE REMOVAL/INSTALLATION.)
5.  Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
6.  Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION.)
7.  B-pillar lower trim (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
8.  Adjust anchor cover (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
9.  Upper anchor installation bolt on the seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
10.  B-pillar upper trim (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
6.  Set the tire house trim aside. (See TIRE HOUSE TRIM REMOVAL/INSTALLATION.)
7.  Remove the following parts:
1.  Rear package tray (See REAR PACKAGE TRAY REMOVAL/INSTALLATION.)
2.  Trunk covering (See TRUNK COVERING REMOVAL/INSTALLATION.)
3.  Trunk board (See TRUNK BOARD REMOVAL/INSTALLATION.)
4.  Trunk end trim (See TRUNK END TRIM REMOVAL/INSTALLATION.)
5.  Trunk side upper trim (See TRUNK SIDE UPPER TRIM REMOVAL/INSTALLATION.)
6.  Trunk side trim (LH only) (See TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
7.  C-pillar trim (See C-PILLAR TRIM REMOVAL/INSTALLATION.)
8.  Headliner (See HEADLINER REMOVAL/INSTALLATION.)

2.  Disconnect the connector.

am3uuw00010478

3.  While pressing the hooks of the rear map light in the direction of arrows (1) shown in the figure, pull the rear map light in the direction of arrow (2) to detach the hooks of the rear map light from the bracket.

Caution
•  When removing the rear map light from the bracket, the rear map light may fall off and be damaged. Remove the rear map light from the bracket while holding the rear map light on the lens side by hand.

4.  Remove the rear map light.

am3uuw00010479

5.  Install in the reverse order of removal.