DTC P02CC:00, P02CE:00, P02D0:00, P02D2:00 [PCM (SKYACTIV-D 2.2)]

id0102j5324300

Note

• To determine the malfunctioning part, proceed with the diagnostics from [Function inspection using M-MDS].

Details on DTCs

System malfunction location

Fuel injector No.1 control system: Correction amount of fuel injection amount and fuel injection timing is too little

Fuel injector No.2 control system: Correction amount of fuel injection amount and fuel injection period is too small

Fuel injector No.3 control system: Correction amount of fuel injection amount and fuel injection timing is too little

Fuel injector No.4 control system: Correction amount of fuel injection amount and fuel injection timing is too little

Detection condition

Determination conditions

•  The PCM determines that the correction amount for the fuel injection amount and the fuel injection timing is too little within the specified time.

Preconditions

•  During fuel injection

Drive Cycle

•  2

Self-test type

•  CMDTC self test

Sensor/unit used

•  Fuel pressure sensor (integrated with fuel injector No.1)

•  Fuel pressure sensor (integrated with fuel injector No.2)

•  Fuel pressure sensor (integrated with fuel injector No.3)

•  Fuel pressure sensor (integrated with fuel injector No.4)

Fail-safe

•  Not applicable

Vehicle status when DTCs are output

•  Not applicable

Possible Cause

•  Fuel injector No.1 malfunction

•  Fuel injector No.2 malfunction

•  Fuel injector No.3 malfunction

•  Fuel injector No.4 malfunction

•  Fuel leakage or clogging in fuel line

•  PCM malfunction

System malfunction location	Fuel injector No.1 control system: Correction amount of fuel injection amount and fuel injection timing is too little Fuel injector No.2 control system: Correction amount of fuel injection amount and fuel injection period is too small Fuel injector No.3 control system: Correction amount of fuel injection amount and fuel injection timing is too little Fuel injector No.4 control system: Correction amount of fuel injection amount and fuel injection timing is too little
Detection condition	Determination conditions	• The PCM determines that the correction amount for the fuel injection amount and the fuel injection timing is too little within the specified time.
Preconditions	• During fuel injection
Drive Cycle	• 2
Self-test type	• CMDTC self test
Sensor/unit used	• Fuel pressure sensor (integrated with fuel injector No.1) • Fuel pressure sensor (integrated with fuel injector No.2) • Fuel pressure sensor (integrated with fuel injector No.3) • Fuel pressure sensor (integrated with fuel injector No.4)
Fail-safe	• Not applicable
Vehicle status when DTCs are output	• Not applicable
Possible Cause	• Fuel injector No.1 malfunction • Fuel injector No.2 malfunction • Fuel injector No.3 malfunction • Fuel injector No.4 malfunction • Fuel leakage or clogging in fuel line • PCM malfunction

System Wiring Diagram

• Not applicable

Function Explanation (DTC detection outline)

• The PCM performs correction learning via the fuel injection amount and the fuel injection timing feedback control. If the condition in which the calculated correction value is the lower limit guard or less exceeds the specified period of time, the PCM determines a fuel injector malfunction and stores DTCs.

Repeatability verification procedure

• Start the engine and warm it up.

― Drive the vehicle on flat roads under the following conditions 4 times repeatedly.

Caution

• Observe legal speed limits when driving the vehicle and perform the procedure in a location where safety can be assured.

1. Accelerate to 15 km/h and decelerate to 0 km/h.

2. Wait for 20 s while idling.

3. Accelerate to 30 km/h, and decelerate to 0 km/h after driving the vehicle while maintaining the speed for 20 s.

4. Wait for 20 s while idling.

5. Accelerate to 50 km/h, and decelerate to 0 km/h after driving the vehicle while maintaining the speed for 20 s.

6. Wait for 20 s while idling.

• Accelerate to 70 km/h and drive the vehicle while maintaining the speed for 60 s.

• Decelerate to 50 km/h and drive the vehicle while maintaining the speed for 60 s.

• Accelerate to 70 km/h and drive the vehicle while maintaining the speed for 60 s.

• Accelerate to 100 km/h and drive the vehicle while maintaining the speed for 30 s.

• Accelerate to 120 km/h and decelerate to 0 km/h.

• Stop the engine.

PID Item/Simulation Item Used in Diagnosis

• Not applicable

Function Inspection Using M-MDS

Step

Inspection

Results

Action

1

PURPOSE: RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION

Note

•  Recording can be facilitated using the screen capture function of the PC.

•  Record the freeze frame data/snap shot data.

—

Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.

2

PURPOSE: DETERMINE INTEGRITY OF FUEL PRESSURE SENSOR

•  Inspect the fuel pressure sensor.

•  Is the fuel pressure sensor normal?

Yes

Go to the next step.

No

Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.

3

PURPOSE: DETERMINE INTEGRITY OF FUEL TEMPERATURE SENSOR

•  Inspect the fuel temperature sensor.

•  Is the fuel temperature sensor normal?

Yes

Go to the next step.

No

Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.

4

PURPOSE: VERIFY OTHER RELATED DTCs

•  Switch the ignition OFF, and then switch it ON (engine off).

•  Display the DTCs using the M-MDS.

•  Have DTCs other than P02CC:00, P02CE:00, P02D0:00, or P02D2:00 been stored, or has pending code been stored?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.

No

Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.

Step	Inspection	Results	Action
1	PURPOSE: RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture function of the PC. • Record the freeze frame data/snap shot data.	—	Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.
2	PURPOSE: DETERMINE INTEGRITY OF FUEL PRESSURE SENSOR • Inspect the fuel pressure sensor. • Is the fuel pressure sensor normal?	Yes	Go to the next step.
No	Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.
3	PURPOSE: DETERMINE INTEGRITY OF FUEL TEMPERATURE SENSOR • Inspect the fuel temperature sensor. • Is the fuel temperature sensor normal?	Yes	Go to the next step.
No	Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.
4	PURPOSE: VERIFY OTHER RELATED DTCs • Switch the ignition OFF, and then switch it ON (engine off). • Display the DTCs using the M-MDS. • Have DTCs other than P02CC:00, P02CE:00, P02D0:00, or P02D2:00 been stored, or has pending code been stored?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.
No	Go to Troubleshooting Diagnostic Procedure to perform the procedure from step 1.

Troubleshooting Diagnostic Procedure

Intention of troubleshooting procedure

• Step 1

― Determine the integrity of the fuel injector.

• Step 2

― Perform the inspection of the fuel system piping.

• Steps 3 to 4

― Verify that the primary malfunction is resolved and there are no other malfunctions.

Step

Inspection

Results

Action

1

PURPOSE: DETERMINE FUEL INJECTOR INTEGRITY

•  Inspect the fuel injector.

•  Are the fuel injectors normal?

Yes

Go to the next step.

No

Replace the fuel injector, then go to the next step.

2

INSPECT FUEL LINE FOR FUEL LEAKAGE OR CLOGGING

•  Inspect the following fuel lines of each cylinder for fuel leakage or clogging.

―  Common rail and fuel injector

•  Is the fuel line normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location, then go to the next step.

3

PURPOSE: VERIFICATION OF VEHICLE REPAIR COMPLETION

•  Reconnect all disconnected connectors and hoses.

•  Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC.

•  Implement the repeatability verification procedure.

•  Display the DTCs using the M-MDS.

•  Is DTC P02CC:00, P02CE:00, P02D0:00, or P02D2:00 displayed?

Yes

Repeat the inspection from Step 1.

•  If the malfunction recurs, replace the PCM, then go to the next step.

No

Go to the next step.

4

PURPOSE: VERIFY IF THERE IS ANY OTHER MALFUNCTION

•  Has any other DTC or pending code been stored?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	PURPOSE: DETERMINE FUEL INJECTOR INTEGRITY • Inspect the fuel injector. • Are the fuel injectors normal?	Yes	Go to the next step.
1		No	Replace the fuel injector, then go to the next step.
2	INSPECT FUEL LINE FOR FUEL LEAKAGE OR CLOGGING • Inspect the following fuel lines of each cylinder for fuel leakage or clogging. ― Common rail and fuel injector • Is the fuel line normal?	Yes	Go to the next step.
2		No	Repair or replace the malfunctioning location, then go to the next step.
3	PURPOSE: VERIFICATION OF VEHICLE REPAIR COMPLETION • Reconnect all disconnected connectors and hoses. • Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC. • Implement the repeatability verification procedure. • Display the DTCs using the M-MDS. • Is DTC P02CC:00, P02CE:00, P02D0:00, or P02D2:00 displayed?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM, then go to the next step.
3		No	Go to the next step.
4	PURPOSE: VERIFY IF THERE IS ANY OTHER MALFUNCTION • Has any other DTC or pending code been stored?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
4		No	DTC troubleshooting completed.