DTC P0500:00 [PCM (SKYACTIV-D 2.2)]

id0102j5704800

DTC P0500:00

VSS circuit problem

DETECTION CONDITION

•  With the following conditions met, a condition has continued for 5 s in which an error signal from the DSC HU/CM is received or no signal can be received from the DSC HU/CM.

―  Battery voltage: Exceeds 10 V.

―  1.5 s have elapsed after ignition is switched ON (engine off or on)

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Limits engine torque.

•  Inhibits the automatic diesel particulate filter regeneration control.

•  Inhibits the manual diesel particulate filter regeneration control.

•  Inhibits the EGR control.

•  Stops the G-vectoring control (GVC).

•  Inhibits engine-stop by i-stop control.

POSSIBLE CAUSE

•  Malfunction in CAN communication line between PCM and DSC HU/CM

•  DSC HU/CM malfunction

•  DSC HU/CM connector or terminal malfunction

•  ABS wheel-speed sensor malfunction

•  PCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P0500:00	VSS circuit problem
DETECTION CONDITION	• With the following conditions met, a condition has continued for 5 s in which an error signal from the DSC HU/CM is received or no signal can be received from the DSC HU/CM. ― Battery voltage: Exceeds 10 V. ― 1.5 s have elapsed after ignition is switched ON (engine off or on) Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Limits engine torque. • Inhibits the automatic diesel particulate filter regeneration control. • Inhibits the manual diesel particulate filter regeneration control. • Inhibits the EGR control. • Stops the G-vectoring control (GVC). • Inhibits engine-stop by i-stop control.
POSSIBLE CAUSE	• Malfunction in CAN communication line between PCM and DSC HU/CM • DSC HU/CM malfunction • DSC HU/CM connector or terminal malfunction • ABS wheel-speed sensor malfunction • PCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION

Note

•  Recording can be facilitated using the screen capture function of the PC.

•  Record the freeze frame data/snap shot data.

—

Go to the next step.

2

VERIFY THAT NO DTCs ARE STORED IN DSC HU/CM

•  Verify that no DTCs are stored in the DSC HU/CM.

•  Has any DTC been stored?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

Inspect the DSC HU/CM connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection.

Repair or replace the malfunctioning location, then go to the next step.

3

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC.

•  Leave for 10 s while idling.

•  Display the DTCs using the M-MDS.

•  Has DTC P0500:00 been recorded?

Yes

Replace the PCM, then go to the next step.

No

Go to the next step.

4

VERIFY OTHER DTCs

•  Has any other DTC or pending code been stored?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture function of the PC. • Record the freeze frame data/snap shot data.	—	Go to the next step.
2	VERIFY THAT NO DTCs ARE STORED IN DSC HU/CM • Verify that no DTCs are stored in the DSC HU/CM. • Has any DTC been stored?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
2		No	Inspect the DSC HU/CM connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection. Repair or replace the malfunctioning location, then go to the next step.
3	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC. • Leave for 10 s while idling. • Display the DTCs using the M-MDS. • Has DTC P0500:00 been recorded?	Yes	Replace the PCM, then go to the next step.
3		No	Go to the next step.
4	VERIFY OTHER DTCs • Has any other DTC or pending code been stored?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
4		No	DTC troubleshooting completed.